噪声调制连续波雷达信号波形射频隐身特性

雷达信号波形的射频(RF)隐身性能是雷达系统能否适应现代战场环境的重要因素,雷达射频隐身信号波形设计是现代雷达系统设计中的重要课题.首先,在介绍随机噪声信号雷达原理的基础上,基于Schleher截获因子阐述了噪声调制连续波雷达信号波形的射频隐身特性.然后,分析了高斯噪声相位和频率调制连续波雷达输出自相关函数和高斯噪声相...     

Multipath and ground clutter analysis for a UWB noise radar

An ultrawideband (UWB) random-noise radar operating in the 1-2 GHz frequency band has been developed and field-tested up to a 200 m range at the Environmental Remote Sensing Laboratory (ERSL) of the University of Nebraska. A unique heterodyne correlation technique based on a delayed transmitted waveform using a photonic delay line has been used to inject coherence within this system. The performance of this radar in the presence of ground reflections is investigated analytically and experimentally, and the mitigating effects of UWB waveform on multipath-induced interference are analyzed. In addition, the ground clutter statistics, in a look-down mode, are theoretically established and experimentally verified. The performance of this radar in detecting clutter embedded targets with small radar cross section (RCS) is also experimentally examined.     

Ambiguity Functions for Quadratic Phase-Coded Pulse Trains

The matched filter ambiguity function is presented for a burst waveform composed of repeated subbursts, each one of which consists of N pulses in which the phase is varied quadratically from pulse to pulse. The resulting ambiguity function exhibits small residual ambiguities along the delay axis separated by the reciprocal of the pulse repetition frequency (PRF). A cross-ambiguity function is derived which reduces these ambiguities to zero amplitude. A third cross-ambiguity function is presented for a receiver matched to a generalized Hamming weighted repeated quadratic burst. The location in the delay/Doppler plane of the waveform ambiguities for these waveforms is compared with that of an uncoded pulse burst.     

A Simple Method for Sampling In-Phase and Quadrature Components

We present a method of developing in-phase and quadrature samples of a band-limited RF waveform. The problem of matching gain and phase response differences between the two components is avoided by a combination of mixing to an IF frequency, sampling and digitizing, and digital filtering. The novelty of the method is in the design of the digital filter, which is realized as a pair of 900 phase splitting networks with several symmetries which are exploited to save computation.     

基于OTR和SHT的射频隐身雷达信号设计

为了提高雷达的射频(RF)隐身性能,结合最优匹配照射-接收机(OTR)理论与序贯假设检验(SHT)方法,提出了一种新的射频隐身雷达信号设计方法。通过发射信号了解外界环境信息,然后反馈这些信息给雷达系统,系统根据这些信息自适应设计雷达发射信号,形成一个闭环系统。以雷达目标识别为具体应用,实验仿真表明,设计的雷达信号自适应变化,减小了信号间的相关性,并且减少了照射次数,降低了辐射功率,从而实现了雷达系统的射频隐身性能。     

利用脉组间频率步进信号合成UWB距离像及类MUSIC法对速度的高分辨估计(英文)

提出一种称为类多信号分类(CMUSIC)的方法,其利用脉组间频率步进信号,在具有M个脉冲的脉冲串(子带,即窄带)中高分辨估计径向速度。利用此速度估计值补偿距离-多普勒耦合和多普勒色散后,对跨子带进行快速傅里叶变换则可获得合成超宽带高分辨距离像。和其他方法相比,CMUSIC在低信噪比时具有较好的速度估计性能。当M大于具有不同径向速度的目标个数Q时,该方法在小M值下依然有优越的速度估计性能。此外,经过径向速度解模糊后,该方法适应高径向速度运动的目标。随着国防技术的突飞猛进地发展以及高速先进飞行器的涌现,这具有重要的实际价值。仿真结果验证了该方法的可行及有效性。     

A novel range-Doppler imaging algorithm with OFDM radar

Traditional pulse Doppler radar estimates the Doppler frequency by taking advantage of Doppler modulation over different pulses and usually it requires a few pulses to estimate the Doppler frequency. In this paper, a novel range-Doppler imaging algorithm based on single pulse with orthogonal frequency division multiplexing(OFDM) radar is proposed, where the OFDM pulse is composed of phase coded symbols. The Doppler frequency is estimated using one single pulse by utilizing Doppler modulation over different symbols, which remarkably increases the data update rate. Besides, it is shown that the range and Doppler estimations are completely independent and the well-known range-Doppler coupling effect does not exist. The effects of target movement on the performances of the proposed algorithm are also discussed and the results show that the algorithm is not sensitive to velocity. Performances of the proposed algorithm as well as comparisons with other range-Doppler algorithms are demonstrated via simulation experiments.     

Nullifying ACF grating lobes in stepped-frequency train of LFM pulses

An effective way to increase the bandwidth of a coherent pulse-train is to add a frequency step /spl Delta/f between consecutive pulses. A large /spl Delta/f implies a large total bandwidth, hence improved range resolution. However, when the product of the frequency step times the pulse-duration t/sub p/, is larger than one (t/sub p/ /spl Delta/f > 1), the autocorrelation function (ACF) of the stepped-frequency pulse-train suffers from ambiguous peaks, known as "grating lobes." It is well known that replacing the fixed-frequency pulses with linear FM (LFM) pulses of bandwidth B can reduce those grating lobes. We present a simple analytic expression for the ambiguity function (AF) and ACF of such a signal and derive from it very simple relationships between /spl Delta/f, B, and t/sub p/ that will place s exactly where the grating lobes are located, and thus remove them completely.     

High-Resolution, Radar Coherent Linear FM Microwave Source

The microwave CLFM study was directed to generating 14 ?s S-band pulses of 1000 MHz bandwidth and an rms phase error of a few degrees. Over 972 MHz bandwidth, the sampled phase error relative to the reference was 7 degrees rms and 17 degrees peak, with a maximum Fourier component of 4 degrees. The FM pulse train is generated by a gated BWO driven by a stable linearizing waveform. Phase coherency during each pulse is obtained by a sampling technique, where the phase is corrected at intervals of 1/6 ?s, the RF phase having changed an integral number of cycles in each interval. Multiplication of the BWO signal by the sampling pulse train results in band-limited phase error pulses which are applied in a feedback loop. Pulse-to-pulse coherency is obtained by phase lock of the BWO starting frequency to the crystal reference. Feedback leveling holds the output constant to 0.3 dB. The basic MITRE technique was originally demonstrated at 10 MHz in 1964. Range results measured with the X-band model radar using the CLFM generator are given and confirm the phase errors of the CLFM.     

Doppler visibility of coherent ultrawideband random noise radar systems

Random noise radar has recently been used in a variety of imaging and surveillance applications. These systems can be made phase coherent using the technique of heterodyne correlation. Phase coherence has been exploited to measure Doppler and thereby the velocity of moving targets. The Doppler visibility, i.e., the ability to extract Doppler information over the inherent clutter spectra, is constrained by system parameters, especially the phase noise generated by microwave components. Our paper proposes a new phase noise model for the heterodyne mixer as applicable for ultrawideband (UWB) random noise radar and for the local oscillator in the time domain. The Doppler spectra are simulated by including phase noise contamination effects and compared with our previous experimental results. A genetic algorithm (GA) optimization routine is applied to synthesize the effects of a variety of parameter combinations to derive a suitable empirical formula for estimating the Doppler visibility in dB. According to the phase noise analysis and the simulation results, the Doppler visibility of UWB random noise radar depends primarily on the following parameters: 1) the local oscillator (LO) drive level of the receiver heterodyne mixer, 2) the saturation current in the receiver heterodyne mixer, 3) the bandwidth of the transmit noise source, and 4) the target velocity. Other parameters such as the carrier frequency of the receiver LO and the loaded quality factor of the LO have a small effect over the range of applicability of the model and are therefore neglected in the model formulation. The Doppler visibility curves generated from this formula match the simulation results very well over the applicable parameter range within 1 dB. Our model may therefore be used to quickly estimate the Doppler visibility of random UWB noise radars for trade-off analysis     

Localization performance of arrays subject to phase errors

The passive localisation of radiating sources using an array subject to random perturbations in sensor phases is presented. All source signals as well as additive noises observed at the sensors are assumed to be independent identically distributed zero-mean Gaussian random processes. Cramer-Rao bounds are derived for source bearings and ranges for the phase errors at each sensor. It is shown that accurate phase calibration can be achieved when the number of sources exceeds a certain minimum. The locations of the calibrating sources need not be known a priori and need only satisfy mild regularity conditions. A calibration procedure is proposed which uses maximum-likelihood techniques     

超宽带电磁脉冲天线阵互耦效应研究

将超宽带电磁脉冲天线组阵后可提高主射方向的峰值功率及增益。但由于非线性阵元因素,必须考虑阵元间互耦效应。以恒阻抗TEM喇叭天线为阵元,通过仿真和实验研究了超宽带天线阵的互耦效应,研究表明,耦合强弱与阵元间距及频段有关,互耦增强了超宽带天线阵的低频辐射能力,使远场主射方向脉冲峰峰值有所增加。上述结论对于超宽带电磁脉冲天线阵的应用具有参考价值。     

基于PSWF 的TH-PPM超宽带系统优化设计与仿真

在分析PSWF脉冲的最佳时域能量聚集性和频谱灵活可控性的基础上,提出了满足FCC(FederalCommunications Commission)频谱掩膜要求的UWB脉冲波形优化设计方法,并将该方法应用于多进制TH-PPM超宽带系统中,理论计算了基于PSWF脉冲的多进制PPM-UWB系统的符号差错率公式。与高斯脉冲进行比较,采用Systemview可视化仿真平台进行了仿真。仿真结果表明,基于PSWF脉冲的UWB系统符号差错率性能要明显优于Gauss脉冲。在给定SER的前提下,使用PSWF脉冲的UWB系统能够容纳更多的用户。     

一种步进频率信号认知雷达波形优化设计方法

认知雷达常用于完成探测、跟踪、成像及识别等多重任务,为提高其综合性能,需兼顾多方面因素研究其波形优化设计问题。基于此,提出一种基于压缩感知（CS）RIPless准则的步进频率信号认知雷达波形优化设计方法。首先,建立了目标回波信号稀疏模型,分析了其与发射信号模糊函数之间的关系。其次,根据模型中观测矩阵的构造,基于RIPless准则,将波形设计问题转化为概率分布的互相干参数及其协方差矩阵的条件数的优化问题,从而通过自适应寻优算法,获得优化的步进频率信号脉冲重复时间间隔序列和子脉冲频率序列。相较于传统方法,所提方法在信号发射与接收之间形成了信息实时反馈和信号优化重构的闭环,在高概率准确重构目标径向一维距离像的同时,也实现了发射信号模糊函数的优化。最后,仿真计算验证了所提方法的有效性。     

A novel target detection approach based on adaptive radar waveform design

To resolve problems of complicated clutter, fast-varying scenes, and low signal-clutterratio (SCR) in application of target detection on sea for space-based radar (SBR), a target detection approach based on adaptive waveform design is proposed in this paper. Firstly, complicated sea clutter is modeled as compound Gaussian process, and a target is modeled as some scatterers with Gaussian reflectivity. Secondly, every dwell duration of radar is divided into several sub-dwells. Regular linear frequency modulated pulses are transmitted at Sub-dwell 1, and the received signal at this sub-dwell is used to estimate clutter covariance matrices and pre-detection. Estimated matrices are updated at every following sub-dwell by multiple particle filtering to cope with fast-varying clutter scenes of SBR. Furthermore, waveform of every following sub-dwell is designed adaptively according to mean square optimization technique. Finally, principal component analysis and generalized likelihood ratio test is used for mitigation of colored interference and property of constant false alarm rate, respectively. Simulation results show that, considering configuration of SBR and condition of complicated clutter, 9 dB is reduced for SCR which reliable detection requires by this target detection approach. Therefore, the work in this paper can markedly improve radar detection performance for weak targets.     

Digital beamforming calibration for FMCW radar

Three sources of beamforming deterioration are identified for an FMCW radar. These all relate to time-of-arrival and cable delays. There are small range-dependent phase errors at the receiver outputs. The delays cause frequency shifts, which produce phase errors at the discrete Fourier transform (DFT) outputs after ranging. These frequency shifts cause amplitude errors when the signals are resolved into the same range bin. Two methods of compensating for phase and amplitude errors are proposed. The first corrects for phase errors prior to beamforming. Amplitude errors are ignored but the residual error is usually small. The second method aligns the receiver frequencies digitally before ranging. This eliminates the phase errors and the amplitude errors at the DFT range estimates     

Software approach to access UWB interference on GPS receivers

Ever since the FCC approved the use of UWB devices in commercial and federal bands, various agencies whose operations and/or products rely on the integrity of signals within certain "restricted" radio frequency bands have voiced concerns over the potential impact of the UWB interference. GPS signals are among these "restricted" bands. Several groups in the GPS community have conducted experimental studies concerning the impact of UWB interference on the performance of various grades of commercial and aviation GPS receivers. In this paper, we present a software approach to simulate and evaluate UWB interference on GPS receivers. The software approach provides greater flexibility in the design of testing scenarios, such as the inclusion of a large number of aggregated UWB devices, the generation of new UWB signals and modulation schemes, and the possibility of extending the study to new GPS signals. The paper discusses a general framework for developing algorithms to evaluate UWB and GPS interference under a wide variety of hardware and software conditions. This framework consists of three classes of components: input, processing, and analysis. The input components are responsible for the generation of UWB signal waveforms and modulation schemes, and GPS signals. The processing components include a simulated model of GPS RF front end and software implementation of GPS processing blocks, such as acquisition, tracking, and post-processing. The analysis components focus on the study of specific receiver processing component outputs. Both real and simulated UWB signals can be used in the study. The real UWB signals are primarily used to validate the simulation procedure, whereas the simulated UWB signals are used to allow the immediate incorporation of new UWB waveforms and modulations in the evaluations. This paper presents details of the software components developed and the preliminary results achieved     

Conopulse Radar Angle Tracking Accuracy

An analysis is given of the tracking accuracy of a conopulse radar that angle-tracks on target echo pulses. The analysis includes effects of noises in both sum and difference channels, the effect of the tracking range gate's duration, and applies to any shape of radio frequency (RF) pulse envelope. For large single-pulse signalto-noise ratio and any shape of RF pulse envelope, accuracy approaches the theoretical accuracy of a conopulse system when a short-duration range gate is used. The inportant case of rectangular RF pulses is solved in detail.     

Sparse frequency transmit-and-receive waveform design

A computationally efficient algorithm derives complex digital transmit and receive ultra-wideband radar and communication waveforms with excellent arbitrary frequency band suppression and range sidelobe minimization. The transmit waveform minimizes a scalar function penalizing weighted spectral energy in arbitrary frequency bands. Near constant power results from another penalty function for deviations from constant power, or constant power is enforced by a phase-only formulation. Next, a least squares solution for the receive waveform minimizes a weighted sum of suppressed band spectral energy and range sidelobes (for pulse and continuous wave operation), with a mainlobe response constraint. Both waveforms are calculated by iterative algorithms whose updates require only linear order in memory and computation, permitting quick calculation of long pulses with thousands of samples.     

一种孔径和频率二维稀疏的步进频SAR成像方法

 步进频率信号(SFWs)在不增加雷达系统瞬时带宽的情况下能够获得高的距离向分辨率的同时,也存在着抗干扰能力较差及其等效重复频率较低的问题,并且在方位向积累时间内由于雷达载机工作状态的变化,会导致方位向的数据录取不完整。针对上述问题,提出一种孔径和频率二维稀疏的步进频合成孔径雷达(SAR)成像方法。首先,分析了稀疏步进频率信号(SSFWs)的SAR成像模型,然后基于压缩感知理论完成距离向成像处理。其次,针对稀疏孔径的回波数据,通过构造成像算子和压缩感知重建模型的方法实现其距离徙动校正和方位压缩处理,进而获得二维成像结果。相比于传统的步进频率信号SAR成像,利用所提方法能够在少量的频率资源和雷达回波数据情况下实现准确的SAR成像。最后,通过对仿真和实测的步进频率雷达数据进行成像处理,验证了所提方法的有效性和可行性。