相控阵雷达与第四代战斗机

从第四代战斗机对机载雷达的需求出发,分析和比较了机械扫描雷达与相控阵雷达的系统特性。介绍了美国和欧洲的第四代战斗机雷达。指出相控阵体制是下一代机载雷达主要发展方向。     

雷达空对地测距试飞方法研究

阐述了一种利用GPS作为基准测量设备来鉴定机载雷达空对地测距(AGR)精度的试飞方法。通过试验及系统的分析、研究证明，该方法对解决机载雷达定型试飞中AGR精度在飞机平飞状态下如何验证这一难题和今后雷达定型试飞中其它科目试飞具有指导意义。     

246雷达数据处理机系统软件设计

机载雷达数据处理机（ Ｒ Ｄ Ｐ） 作为现代机载雷达核心之一，向下完成数据处理和协调其它各分机的工作，向上则实现与机载航空电子分系统的通讯，因此数据处理机的软件是整个雷达的灵魂。本文详细介绍为 Ｂｏｍ ｂ 飞机的雷达数据处理机设计的系统软件。     

机载雷达单机价格参数估算方法研究

机载雷达单机价格的控制对于降低现代作战飞机价格至关重要。采用偏最小二乘法建立机载雷达单机价格参数化估算模型。以国外8个雷达型号作为样本,进行估算,结果表明模型对机载雷达研制费的解释能力为0.984,能较准确地对机载雷达单机价格进行估算。该模型已应用于实际,效果较好。     

机载雷达综合显示器的仿真实现

雷达综合显示器是一种能够灵活地把雷达一次信息、二次信息、地图背景和各种表格数据综合在同一个显示界面进行显示的雷达终端系统,可以形象地提供雷达威力范围内比较全面的综合信息。本文对应用Visual C＋＋程序设计来实现航空机载雷达综合显示器的仿真问题进行了探讨。     

机载雷达可靠性设计与试验

在简要说明机载雷达可靠性研究的意义后,详细阐述了对歼击飞机火控雷达开展可靠性设计、可靠性试验、可靠性增长等工作的情况,总结了雷达研制中可靠性设计方法,并给出系统进一步提高可靠性的工作程序。     

机载雷达综合训练模拟器的研制

首先分析机载雷达综合训练模拟器的功能,然后详细论述雷达训练模拟器的软硬件组成,以及系统研制过程中所解决的关键问题。     

中航工业雷达与电子设备研究院

<正>中航工业雷达与电子设备研究院于2004年3月由中国航空工业第六O七研究所和苏州长风有限责任公司整合成立,在无锡和苏州分设研发中心和生产试验基地,是集机载雷达、显示器等航空电子设备研发、试验、制造为一体的科技先导型研究院,业务范围覆盖了政府系统和商用系统两大领域,涉及综合监视系统、机载雷达、座舱显示器、广播电视网络传输设备、专用传感器件等众多产品。     

中航工业雷达与电子设备研究院

<正>中航工业雷达与电子设备研究院于2004年3月由中国航空工业第六○七研究所和苏州长风有限责任公司整合成立,在无锡和苏州分设研发中心和生产试验基地,是集机载雷达、显示器等航空电子设备研发、试验、制造为一体的科技先导型研究院,业务范围覆盖了政府系统和商用系统两大领域,涉及综合监视系统、机载雷达、座舱显示器、广播电视网络传输设备、专用传感器件等众多产品。     

单机空战智能仿真系统的建立

从主要功能、模型建立、主要特点等几个方面介绍了单机空战智能仿真系统。重点介绍神经网络决策模型和飞机、雷达、导弹模型的建立。飞机机动模型采用质点运动方程，选用19个基本机动动作；机载雷达模型着重介绍雷达发现和截获目标以及盲区确定的条件；导弹模型主要介绍导弹发射、跟踪、命中条件的建立和计算；决策模型主要介绍多层前馈反向网络决策模型的输入、输出参烽以及网络拓扑结构。此外还介绍了该仿真系统在实践中的使用情况。     

基于飞机油箱模型形状特征油量测量切片步长选择方法研究

 在分析飞机数字式油量测量过程中目前广泛使用的切片法油量测量原理的基础上,针对现有的定步长切片法无法得到准确、可靠的燃油质量特性数据库的缺陷,结合对飞机油箱模型形状特征的分析,提出了基于飞机油箱模型形状特征的油量测量切片步长选择方法。此方法包括切片步长整体和局部选择两个过程,整体选择以实现相邻两切片平面所夹油箱模型体积近似相等为目的来确定切片步长,以体现油箱模型截面整体变化规律;局部选择以设计切片平面与截面突变平面重合或尽可能接近的方式,突出油箱截面的局部变化特征。实验结果表明：该切片步长选择方法较定步长方法能够建立更为合理、可靠的燃油质量特性数据库,从而提高了油量测量精度。     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

二维翼段颤振的μ控制

 采用超声电机作为作动器来实现含控制面的翼段颤振鲁棒抑制。针对作者设计的二维翼段颤振主动抑制系统，通过理论与实验相结合的方法，建立了考虑沉浮方向阻尼和作动器模型参数不确定性的控制系统模型，设计了μ控制器，并对控制器做了降阶处理。数值仿真和风洞试验表明，μ控制器可有效地抑制颤振的发生，将颤振临界速度提高23.4%。相对于H_∞控制器，μ控制器的控制效果和鲁棒性更好。     

Abnormal Shape Mould Winding

为解决网格化芯模的缠绕问题,本文提出了复合材料面片缠绕机理;接着详细分析了面片缠绕过程中的芯模凹曲面上纤维滑线和架空现象,应用微分几何曲面理论和空间几何理论,提出判据及其解决方案;最后,针对飞机发动机进气道的缠绕成型,编制缠绕控制程序并进行相应的实验,验证了面片缠绕方法的可行性。     

基于H∞性能指标的质量矩拦截弹鲁棒控制

 以所建立的质量矩拦截弹数学模型为基础，利用微分几何的反馈线性化理论，得到一个解耦线性系统，考虑到拦截弹的鲁棒性要求和3个滑块的协调控制问题，提出采用双回路的设计方法，内回路采用线性二次调节器（LQR），外回路采用考虑混合灵敏度问题的H_∞控制设计。仿真结果证明了该方法动态性能满足设计要求，同时对系统参数的不确定性具有较强的鲁棒性。     

航天器返回地球的气动特性综述

航天器返回地球的飞行过程中,气动特性是实现将宇宙飞行速度减到落地前速度、保证再入飞行得到有效控制以及再入防热安全可靠的关键因素。针对简单旋成体气动外形、半弹道式再入控制、烧蚀防热类返回航天器,综述了返回地球过程中变化的空气流域特性、航天器周围的气体绕流环境、空气与航天器作用产生的动力学与热效应等。系统地给出了该类航天器的再入气动特性参数与飞行性能的共性规律,包括:气动阻力与再入减速、气动升力与再入轨迹控制、配平攻角与飞行稳定性、气动加热与防热,以及再入过程中不同气动特性航天器、气象条件变化等对再入飞行性能的影响规律。为航天器开展返回飞行过程的跨流域气动性能工程研制提供设计参考。     

Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis

Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.     

Effects of Mo on the Microstructure and Hydrogen Sorption Properties of Ti-Mo Getters

The effects of Mo on the microstructure evolution, porosity and hydrogen sorption properties of Ti-Mo getters are investigated in this work. The results show that the addition of Mo prolongs the densification process of Ti-Mo getters and results in a significant amount of sintered pores. With the Mo content increasing, the porosity of getters firstly increases reaching the maximum value as it at- tains about 7.5wt.%, and then drops. At the room temperature, the hydrogen sorption property of getters increases progressively with the Mo content increasing, but the tendency is not very clear before its content lies below 2.5wt.%. When the Mo content achieves about 7.5wt.%, the hydrogen sorption property proves to be the best. The discussion is made about the above mentioned phenomena inclusive of hydrogen sorption properties of getters under different activation conditions (from 500-750 ℃).     

Preparation of Highly Dispersed Antimony-doped Tin Oxide Nano-powder via Ion-exchange Hydrolysis of SnCl4 and SbCl3 and Azeotropic Drying

Antimony-doped tin hydroxide colloid precipitates have been synthesized by hydrolysis of SnCl4 and SbCl3 using: (1) an ion-exchange hydrolysis to remove chlorine ions, and (2) isoamyl acetate as an azeotropic solvent to obviate water. The obtained dried powder is of high dispersivity without any need for further grinding. The size and dispersivity of the final particles are investigated with the aid of TG-DTA, BET, XRD and TEM. After having calcined, the antimony-doped tin oxide nanopowder possesses a tetragonal rutile structure with high dispersivity, uniform particles and low hard agglomeration.