共查询到20条相似文献,搜索用时 93 毫秒
1.
钛酸钾晶肽/A—90橡胶复合材料的研究 总被引:3,自引:0,他引:3
本文研究了钛酸钾晶须对氯丁橡胶复合材料物理机械性能的影响,研究结果表明,对钛酸钾晶须进行偶联处理能显著提高橡胶复合材料的撕裂强度和耐溶剂性能。 相似文献
2.
3.
简要介绍了国内外复合材料修理技术现状和国内复合材料技术研究存在的主要问题,有针对性地提出了机体复合材料修理技术研究的基本要求和方法,并介绍了复合材料修复金属结构等技术,对复合材料修理技术的发展趋势进行了预测。 相似文献
4.
对缝合复合材料的性能测试方法及应变计尺寸的选取进行了研究,初步确定了适用于缝合复合材料力学性能测试的最小应变计尺寸,并且初步给出了缝合参数对复合材料基本力学性能的影响趋势,为今后进行纺织复合材料的研究提供了必要的技术储备。 相似文献
5.
对碳纤维/氰酸酯复合材料的吸湿、空间放气、吸湿变形性能进行了研究,并与传统碳纤维/环氧复合材料的性能进行对比。研究表明:氰酸酯基复合材料的吸湿性能优于碳纤维/环氧树脂复合材料,且其各项空间环境性能均与环氧树脂基复合材料相当。 相似文献
6.
赵伟栋%张宗强%耿东兵%熊玉峰%王文虎 《宇航材料工艺》2003,33(5):21-25
对耐低温树脂基复合材料的研究背景及国内外研究现状进行了概述,并对聚合物基纳米复合材料,特别是插层复合材料的性能作了介绍。提出了解决液氢贮箱耐低温、防渗漏关键技术的研究设想。 相似文献
7.
复合材料应用研究项目的系统工程管理(下)航空工业总公司王慧杰三、“复合材料应用研究”系统的分析与模型根据上述对复合材料应用研究系统的分析,提出图2所示的复合材料应用研究系统,它表达了系统的层次和子系统结构及其相互的关系,并作为系统结构层次和相互关系的... 相似文献
8.
9.
10.
11.
Based on study of strain distribution in whisker reinforced metal matrix composites, an explicit precise stiffness tensor is derived. In the present theory, the effect of whisker orientation on the macro property of composites is considered, but the effect of random whisker position and the complicated strain field at whisker ends are averaged. The derived formula is able to predict the stiffness modulus of composites with arbitrary whisker orientation under any loading condition. Compared with the models of micro-mechanics, the present theory is competent for modulus prediction of actual engineering composites. The verification and application of the present theory are given in a subsequent paper published in the same issue. 相似文献
12.
PREDICTION OF MECHANICAL PROPERTY OF WHISKER REINFORCED METAL MATRIX COMPOSITE: PART-I. MODEL AND FORMULATION 总被引:1,自引:0,他引:1
Whisker reinforced metal matrix compositespossess good transverse strength,low cost,high workability and other properties over unre-inforced alloys.They are applied increasingly inaerospace,automotive,electronics,sportinggoods and many other areas.Creation of thosecomposites has led to the development of newtest methods,manufacturing techniques,predic-tion theory and design practices[1,2 ] . The pioneer works on prediction of the elas-tic moduli of composite were traced back toVoigt[3] and … 相似文献
13.
硼酸铝晶须增强氰酸酯树脂/玻璃布复合材料的研究 总被引:7,自引:0,他引:7
为了改善氰酸酯树脂基复合材料的层间性能,加入硼酸铝(AlBw)晶须制得晶须/氰酸酯树脂/玻璃布复合材料。研究了晶须对氰酸酯树脂的反应活性、工艺性的影响以及对复合材料力学性能的改善效果,并分析了复合材料断裂的SEM照片。凝胶时间和差示扫描量热(DSC)分析表明,晶须的加入对树脂体系反应性影响较小。晶须的加入增大了氰酸酯树脂的粘度,但增加幅度不大,当晶须加入质量为20%时树脂粘度仍小于8Pa·s,具有良好的工艺性。随晶须加入量的增加,复合材料的层间剪切强度(ILSS)和弯曲强度增大,晶须质量占10%时,4%硼酸酯处理的晶须使ILSS和弯曲强度分别提高45%和32%。晶须的加入使复合材料耐湿热性提高,水煮100h后,吸水率降为1.09%,力学强度保持率高于85%。 相似文献
14.
以不同界面层厚度的SiC纤维为增强相,采用先驱体浸渍裂解工艺(PIP)制备SiCf(PyC)/SiC复合材料,并在复合材料基体中引入SiC晶须,对其性能进行研究。结果表明:热解碳(PyC)界面层厚度约为230 nm时,SiC纤维拔出明显,SiCf/SiC复合材料拉伸强度、弯曲强度和断裂韧度分别达到192.3 MPa、446.9 MPa和11.4 MPa?m1/2;在SiCf/SiC复合材料基体中引入SiC晶须后,晶须的拔出、桥连及裂纹偏转等增韧机制增加了裂纹在基体中传递时的能量消耗,使复合材料的断裂韧度和弯曲强度分别提高了22.9%和9.1%。 相似文献
15.
16.
17.
应用扫描电镜-图像仪联机系统,定量测量压铸态SiCW/6061Al材料中晶须取向分布。借助X射线应力仪,测定复合材料中的残余应力。结果表明,晶须在垂直压铸方向有择优性,残余应力在垂直压铸方向的分量较大。随温度升高,残科应力的变化为:拉应力,零应力-压应力,各应力分量具有相近的零应力温度。 相似文献
18.
胡晓兰%朱光明%梁国正 《宇航材料工艺》2002,32(2):12-17
主要介绍了硼酸铝晶须的特性、制备方法及其在热固性树脂与热塑性树脂和医学中的应用研究概况,以及硼酸铝晶须的表面处理对复事材料性能的影响,并提出晶须的表面改性、材料的加工工艺及降低制造成本是今后发展的主要方向。 相似文献
19.
The present paper continues the discussion in Part-I. Model and Formulation. Based on the theory proposed in Part-I, the formulae predicting stiffness moduli of the composites in some typical cases of whisker orientations and loading conditions are derived and compared with theoretical representatives in literatures, experimental measurement and commonly-used empirical formulae. It seems that (1) with whisker reinforcing and matrix-hardening considered, the present prediction is in well agreement with the experimental measurement; (2) the present theory can predict accurate moduli with the proper pre-calculated parameters; (3) the upper-bound and lower-bound of the present theory are just the predictions of equal strain theory and equal stress theory; (4) the present theory provides a physical explanation and theoretical base for the present commonly-used empirical formulae. Compared with the microscopic mechanical theories, the present theory is competent for modulus prediction of practical engineering composite in accuracy and simplicity. 相似文献