短螺旋型燃烧室旋流结构及气动边界发展规律数值模拟研究

短螺旋型燃烧室的头部轴线沿发动机周向与发动机轴线偏转一定角度,可以在保证燃烧效率不变的条件下有效缩短燃烧室轴向长度。短螺旋型燃烧室流场的最大特点是旋流流动单侧受限。为了研究头部安装角α变化对燃烧室旋流流动特性的影响,基于数值方法对短螺旋型燃烧室进行了计算分析。结果表明:随着α变化,旋流器下游旋涡依次出现对称环状、马蹄状、环状结构;随着α增加,气动边界逐渐出现并抑制旋流的周向扩张,导致流场出现不同的旋涡结构;不同α下的切向角动量随轴向距离增加而衰减,但α为35°和45°时,气动边界在非受限侧出现并对旋流产生约束,角动量衰减变慢;当α为0°,15°,35°,45°时,燃油液滴依次集中分布在旋流器下游两旋涡边缘、侧壁面和头部端壁、非受限旋涡边缘。本文研究了不同α下的旋涡结构及气动边界沿轴向的演化过程,为短螺旋型燃烧室进一步的设计与优化提供基础。     

Application of a PCA-DBN-based surrogate model to robust aerodynamic design optimization

An efficient method employing a Principal Component Analysis (PCA)-Deep Belief Network (DBN)-based surrogate model is developed for robust aerodynamic design optimization in this study. In order to reduce the number of design variables for aerodynamic optimizations, the PCA technique is implemented to the geometric parameters obtained by parameterization method. For the purpose of predicting aerodynamic parameters, the DBN model is established with the reduced design variables as input and the aerodynamic parameters as output, and it is trained using the k-step contrastive divergence algorithm. The established PCA-DBN-based surrogate model is validated through predicting lift-to-drag ratios of a set of airfoils, and the results indicate that the PCA-DBN-based surrogate model is reliable and obtains more accurate predictions than three other surrogate models. Then the efficient optimization method is established by embedding the PCA-DBN-based surrogate model into an improved Particle Swarm Optimization (PSO) framework, and applied to the robust aerodynamic design optimizations of Natural Laminar Flow (NLF) airfoil and transonic wing. The optimization results indicate that the PCA-DBN-based surrogate model works very well as a prediction model in the robust optimization processes of both NLF airfoil and transonic wing. By employing the PCA-DBN-based surrogate model, the developed efficient method improves the optimization efficiency obviously.     

火箭发动机超声速过膨胀射流气动噪声特性研究

采用大涡模拟LES方法计算了火箭发动机超声速过膨胀射流形态及近场声压分布,研究了入口温度与环境温度的比值(温度比)对声场的影响;将声源分解,基于Ffowcs Williams-Hawkings (FW-H)方程获取了不同位置噪声源的远场噪声,并根据声压级频谱和湍流形态分析了超声速射流噪声的产生机理。研究表明,超声速过膨胀射流气动噪声由湍流混合噪声和宽频激波噪声组成,近场噪声源以马赫波形式向大方位角辐射中高频噪声,下游大尺度湍流向低方位角范围辐射低频噪声,声压级峰值频率随观测角度增大而升高;随温度比升高,马赫波辐射角度增大,噪声指向性发生改变。该研究可为运载火箭发动机地面试车或火箭发射段声学环境设计提供参考。     

Assessment on critical technologies for conceptual design of blended-wing-body civil aircraft

Civil aviation faces great challenges because of its robust projected future growth and potential adverse environmental effects. The classical Tube-And-Wing(TAW) configuration following the Cayley's design principles has been optimized to the architecture's limit, which can hardly satisfy the further requirements on green aviation. By past decades' investigations the BlendedWing-Body(BWB) concept has emerged as a potential solution, which can simultaneously fulfill metrics of noise, emission and fuel burn. The purpose of the present work is to analyze the developments of critical technologies for BWB conceptual design from a historical perspective of technology progress. It was found that the high aerodynamic efficiency of BWB aircraft can be well scaled by the mean aerodynamic chord and wetted aspect ratio, and should be realized with the trade-offs among stability and control and low-speed performance. The structure concepts of non-cylinder pressurized cabin are of high risks on weight prediction and weight penalty. A static stability criterion is recommended and further clear and adequate criteria are required by the evaluations of flying and handling qualities. The difficulties of propulsion and airframe integration are analyzed. The energy to revenue work ratios of well-developed BWB configurations are compared,which are 31.5% and 40% better than that of TAW, using state-of-art engine technology and future engine technology, respectively. Finally, further study aspects are advocated.     

Aerodynamic optimization design for high pressure turbines based on the adjoint approach

A first study on the continuous adjoint formulation for aerodynamic optimization design of high pressure turbines based on S2surface governed by the Euler equations with source terms is presented.The objective function is defined as an integral function along the boundaries,and the adjoint equations and the boundary conditions are derived by introducing the adjoint variable vectors.The gradient expression of the objective function then includes only the terms related to physical shape variations.The numerical solution of the adjoint equation is conducted by a finitedifference method with the Jameson spatial scheme employing the first and the third order dissipative fluxes.A gradient-based aerodynamic optimization system is established by integrating the blade stagger angles,the stacking lines and the passage perturbation parameterization with the quasi-Newton method of Broyden–Fletcher–Goldfarb–Shanno(BFGS).The application of the continuous adjoint method is validated through a single stage high pressure turbine optimization case.The adiabatic efficiency increases from 0.8875 to 0.8931,whilst the mass flow rate and the pressure ratio remain almost unchanged.The optimization design is shown to reduce the passage vortex loss as well as the mixing loss due to the cooling air injection.     

冲压发动机气膜冷却分析模型

本文建立了冲压发动机燃烧室气膜冷却传热分析程序。根据燃烧室设计的技术要求,从冷却性能角度完成气膜冷却系统的气动性能和传热特性分析,提供冷却结构优化所需的信息。     

A surface parametric control and global optimization method for axial flow compressor blades

An aerodynamic optimization method for axial flow compressor blades available for engineering is developed in this paper. Bezier surface is adopted as parameterization method to control the suction surface of the blades, which brings the following advantages:(A) significantly reducing design variables;(B) easy to ensure the mechanical strength of rotating blades;(C) better physical understanding;(D) easy to achieve smooth surface. The Improved Artificial Bee Colony(IABC) algorithm, which significantly increases the convergence speed and global optimization ability, is adopted to find the optimal result. A new engineering optimization tool is constructed by combining the surface parametric control method, the IABC algorithm, with a verified Computational Fluid Dynamics(CFD) simulation method, and it has been successfully applied in the aerodynamic optimization for a single-row transonic rotor(Rotor 37) and a single-stage transonic axialflow compressor(Stage 35). With the constraint that the relative change in the flow rate is less than0.5% and the total pressure ratio does not decrease, within the acceptable time in engineering, the adiabatic efficiency of Rotor 37 at design point increases by 1.02%, while its surge margin 0.84%,and the adiabatic efficiency of Stage 35 0.54%, while its surge margin 1.11% after optimization, to verify the effectiveness and potential in engineering of this new tool for optimization of axial compressor blade.     

Aerodynamic performance enhancement for flapping airfoils by co-flow jet

Introducing active flow control into the design of flapping wing is an effective way to enhance its aerodynamic performance. In this paper, a novel active flow control technology called Co-Flow Jet (CFJ) is applied to flapping airfoils. The effect of CFJ on aerodynamic performance of flapping airfoils at low Reynolds number is numerically investigated using Unsteady Reynolds Averaged Navier-Stokes (URANS) simulation with Spalart-Allmaras (SA) turbulence model. Numerical methods are validated by a NACA6415-based CFJ airfoil case and a S809 pitching airfoil case. Then NACA6415 baseline airfoil and NACA6415-based CFJ airfoil with jet-off and jet-on are simulated in flapping motion, with Reynolds number 70,000 and reduced frequency 0.2. As a result, CFJ airfoils with jet-on generally have better lift and thrust characteristics than baseline airfoils and jet-off airfoil when C_μ is greater than 0.04, which results from the CFJ effect of reducing flow separation by injecting high-energy fluid into boundary layer. Besides, typical kinematic and geometric parameters, including the reduced frequency and the positions of the suction and injection slot, are systematically studied to figure out their influence on aerodynamic performance of the CFJ airfoil. And a variable C_μ jet control strategy is proposed to further improve effective propulsive efficiency. Compared with using constant C_μ, an increase of effective propulsive efficiency by 22.6% has been achieved by using prescribed variable C_μ for NACA6415-based CFJ airfoil at frequency 0.2. This study may provide some guidance to performance enhancement for Flapping wing Micro Air Vehicles (FMAV).     

Aerodynamics of smart flap under ground effect

Aerodynamic characteristics of two-dimensional smart flap under the ground effect have been assessed by a numerical simulation. In this process, a pressure-based implicit procedure to solve Navier–Stokes equations on a nonorthogonal mesh with collocated finite volume formulation is used. The boundedness criteria for this procedure are determined from the Normalized Variable Diagram (NVD) scheme. The procedure incorporates the k–ε eddy–viscosity turbulence model. Cantilever beam with uniformly varying load with roller support at the free end is considered for the configuration of the smart flap. The method is first validated against experimental data. Then, the algorithm is applied for turbulent aerodynamic flows around airfoil with smart and conventional flaps for different attack angle, flap angle and ground clearance where the results of two flaps are compared. The comparisons show that the quality of the solution is considerable.     

唇口几何参数对短舱进气道性能影响数值研究

针对下一代民用涡扇发动机短舱长径比不断缩小的发展趋势,为改善发动机进口气流参数分布不均、改善进气道的流场结构、提高其气动性能,开展了进气道唇口关键几何参数对短舱进气道流动特性影响的研究。通过CFD数值模拟方法研究了进气道收缩比、唇口超椭圆指数以及唇口超椭圆长短轴比对短舱进气道性能的影响。研究发现,这三个设计参数改变时,均会对进气道性能产生直接的影响,对畸变指数的影响最明显,其中收缩比改变的影响最大,当收缩比每改变0.025,畸变指数的变化率最大可达到50%。进口收缩比的改变影响喉道截面的流动,超椭圆指数变化影响了进口前缘曲率的变化,而超椭圆长短轴比变化影响了进气道唇口内型面的曲率;超椭圆长短轴比越大,超椭圆指数越小,收缩比越大,唇口初始压力损失越大,壁面摩擦损失越大,进气道总压恢复系数越低,畸变程度越高。