唇口几何参数对短舱进气道性能影响数值研究

针对下一代民用涡扇发动机短舱长径比不断缩小的发展趋势,为改善发动机进口气流参数分布不均、改善进气道的流场结构、提高其气动性能,开展了进气道唇口关键几何参数对短舱进气道流动特性影响的研究。通过CFD数值模拟方法研究了进气道收缩比、唇口超椭圆指数以及唇口超椭圆长短轴比对短舱进气道性能的影响。研究发现,这三个设计参数改变时,均会对进气道性能产生直接的影响,对畸变指数的影响最明显,其中收缩比改变的影响最大,当收缩比每改变0.025,畸变指数的变化率最大可达到50%。进口收缩比的改变影响喉道截面的流动,超椭圆指数变化影响了进口前缘曲率的变化,而超椭圆长短轴比变化影响了进气道唇口内型面的曲率;超椭圆长短轴比越大,超椭圆指数越小,收缩比越大,唇口初始压力损失越大,壁面摩擦损失越大,进气道总压恢复系数越低,畸变程度越高。     

压气机转子叶片的抑颤设计(“两机”专刊)

以一高压压气机转子叶片为对象开展了叶片抑颤工程设计方法研究,采用基于相位延迟边界条件的能量法和特征值法对原转子叶片模型的气动弹性稳定性进行评估,通过分析近失速工况下的非定常气动功密度分布,对叶片安装角沿径向分布、弦长和叶尖间隙等设计参数进行调整,以明确各参数对气动弹性稳定性的影响,最终达到提高气动阻尼的目的。研究结果表明：叶尖间隙对气动阻尼的影响较大,安装角次之,弦长影响相对较小。叶片气动阻尼随叶尖间隙的变化并非单调,而是存在一个叶尖间隙使其气动阻尼最小,即叶片气动弹性稳定性最差。减小进口气流攻角和增加折合频率,能够提高气动阻尼,设计中可以通过调节安装角来减小气流攻角,增加弦长来增大折合频率。     

翼吊短舱形式发动机安装效应的风洞试验研究

为了确定实际飞行使用条件下,发动机状态变化时,进排气系统损失对飞机气动特性的影响,本文针对翼吊短舱形式的发动机开展了缩比模型风洞试验,分别进行了基本构型与起飞构型下,马赫数0.1、0.15、0.2,攻角0°~15°变化,5种不同发动机状态条件下的风洞试验,通过数据分析,明确了该类型发动机推/阻力划分的基本方法,分析了发动机状态变化时飞机气动特性的改变及修正方法。风洞试验结果表明：发动机状态变化对飞机升阻特性影响明显,飞机设计研发阶段不能仅对短舱通流模型,或单一发动机状态下的动力短舱模型进行损失修正,必须建立合理的推/阻划分体系,对实际使用条件下,发动机状态变化引起的进排气损失进行修正。     

Advances in critical technologies for hypersonic and high-enthalpy wind tunnel

Hypersonic and high-enthalpy wind tunnels and their measurement techniques are the cornerstone of the hypersonic flight era that is a dream for human beings to fly faster, higher and further. The great progress has been achieved during the recent years and their critical technologies are still in an urgent need for further development. There are at least four kinds of hypersonic and high-enthalpy wind tunnels that are widely applied over the world and can be classified according to their operation modes. These wind tunnels are named as air-directly-heated hypersonic wind tunnel, light-gas-heated shock tunnel, free-piston-driven shock tunnel and detonation-driven shock tunnel, respectively. The critical technologies for developing the wind tunnels are introduced in this paper, and their merits and weakness are discussed based on wind tunnel performance evaluation. Measurement techniques especially developed for high-enthalpy flows are a part of the hypersonic wind tunnel technology because the flow is a chemically reacting gas motion and its diagnosis needs specially designed instruments. Three kinds of the measurement techniques considered to be of primary importance are introduced here, including the heat flux sensor, the aerodynamic balance, and optical diagnosis techniques. The techniques are developed usually for conventional wind tunnels, but further improved for hypersonic and high-enthalpy tunnels. The hypersonic ground test facilities have provided us with most of valuable experimental data on high-enthalpy flows and will play a more important role in hypersonic research area in the future. Therefore, several prospects for developing hypersonic and high-enthalpy wind tunnels are presented from our point of view.     

Global aerodynamic design optimization based on data dimensionality reduction

In aerodynamic optimization, global optimization methods such as genetic algorithms are preferred in many cases because of their advantage on reaching global optimum. However, for complex problems in which large number of design variables are needed, the computational cost becomes prohibitive, and thus original global optimization strategies are required. To address this need, data dimensionality reduction method is combined with global optimization methods, thus forming a new global optimization system, aiming to improve the efficiency of conventional global optimization. The new optimization system involves applying Proper Orthogonal Decomposition (POD) in dimensionality reduction of design space while maintaining the generality of original design space. Besides, an acceleration approach for samples calculation in surrogate modeling is applied to reduce the computational time while providing sufficient accuracy. The optimizations of a transonic airfoil RAE2822 and the transonic wing ONERA M6 are performed to demonstrate the effectiveness of the proposed new optimization system. In both cases, we manage to reduce the number of design variables from 20 to 10 and from 42 to 20 respectively. The new design optimization system converges faster and it takes 1/3 of the total time of traditional optimization to converge to a better design, thus significantly reducing the overall optimization time and improving the efficiency of conventional global design optimization method.     

Aerodynamic optimization design for high pressure turbines based on the adjoint approach

A first study on the continuous adjoint formulation for aerodynamic optimization design of high pressure turbines based on S2surface governed by the Euler equations with source terms is presented.The objective function is defined as an integral function along the boundaries,and the adjoint equations and the boundary conditions are derived by introducing the adjoint variable vectors.The gradient expression of the objective function then includes only the terms related to physical shape variations.The numerical solution of the adjoint equation is conducted by a finitedifference method with the Jameson spatial scheme employing the first and the third order dissipative fluxes.A gradient-based aerodynamic optimization system is established by integrating the blade stagger angles,the stacking lines and the passage perturbation parameterization with the quasi-Newton method of Broyden–Fletcher–Goldfarb–Shanno(BFGS).The application of the continuous adjoint method is validated through a single stage high pressure turbine optimization case.The adiabatic efficiency increases from 0.8875 to 0.8931,whilst the mass flow rate and the pressure ratio remain almost unchanged.The optimization design is shown to reduce the passage vortex loss as well as the mixing loss due to the cooling air injection.     

变形飞行器建模及控制方法研究综述

针对变形飞行器的发展现状、气动建模、动力学建模以及控制方法研究进行了综述。首先阐述了变形飞行器的定义及变形需求,再从四个方面梳理了变形飞行器的技术优势。针对不同的机翼变形方式,对飞行器各种变形技术的特点及发展现状进行了详细的分析与总结;将变形飞行器与固定外形飞行器的气动机理进行了对比分析,并对变形飞行器的动力学建模方法进行了梳理,总结了各种方法的特点;结合变形飞行器自身特性分析了飞行控制的特点及难点,并详细阐述了各类变形飞行器的控制研究进展。最后总结分析了变形飞行器的发展趋势：深化基础理论与技术研究,从材料、结构及控制等领域全方面朝着智能化方向发展,最终实现变形飞行器的工程化、自主化、智能化应用。     

高超声速飞行器气动热耗散、输运及转换技术研究进展

针对高超声速飞行器面临的严重气动热集中、累积和时变问题,从气动热耗散、输运和转换三个方面,分别论述了被动热耗散材料、结构和主动热耗散技术,基于高导热材料、热管和工质对流的热输运技术,以及再生转换和热电转换技术的研究现状及其在高超声速飞行器上的应用案例,提出了上述技术在面临高超声速气动热时存在的问题。最后,针对高超声速飞行器气动热耗散、输运和转换技术的发展趋势进行了展望。     

静子叶栅安装角异常非定常流场数值研究

为了研究静子叶栅安装角异常对叶栅通道流场的影响,利用商业软件NUMECA对二维叶栅某个叶片安装角增加5°不同攻角进行非定常流场数值模拟,得到了因安装角异常导致叶栅通道堵塞时对叶栅通道内的流场结构及叶片载荷的影响。结果表明,安装角调节5°时,在正攻角下,随着攻角的增大叶栅通道内流动不断恶化,吸力面出现大面积的附面层分离;负攻角时,气流比较平稳,但是漩涡脱落频率高达3500Hz。分析发现,安装角异常时攻角对漩涡尺度和脱落频率影响较大,其中叶片动态气动力脉动量迅速增大,可能是导致发动机叶片疲劳破坏的原因之一。     

An artificial neural network approach for aerodynamic performance retention in airframe noise reduction design of a 3D swept wing model

With the progress of high-bypass turbofan and the innovation of silencing nacelle in engine noise reduction, airframe noise has now become another important sound source besides the engine noise. Thus, reducing airframe noise makes a great contribution to the overall noise reduction of a civil aircraft. However, reducing airframe noise often leads to aerodynamic perfor-mance loss in the meantime. In this case, an approach based on artificial neural network is intro-duced. An established database serves as a basis and the training sample of a back propagation (BP) artificial neural network, which uses confidence coefficient reasoning method for optimization later on. Then the most satisfactory configuration is selected for validating computations through the trained BP network. On the basis of the artificial neural network approach, an optimization pro-cess of slat cove filler (SCF) for high lift devices (HLD) on the Trap Wing is presented. Aerody-namic performance of both the baseline and optimized configurations is investigated through unsteady detached eddy simulations (DES), and a hybrid method, which combines unsteady DES method with acoustic analogy theory, is employed to validate the noise reduction effect. The numerical results indicate not merely a significant airframe noise reduction effect but also excel-lent aerodynamic performance retention simultaneously.