天基轻气炮发射清除低轨碎片方案及关键技术分析

文章分析了现有的空间碎片清除方式,并以800~1200 km低地球轨道高度上1~10 cm量级的空间碎片为清除目标,提出了天基轻气炮清除碎片的新方法。首先分析了轻气炮有效载荷在典型参数下的弹丸加速能力;之后根据将碎片降轨使其坠入大气层烧毁的设想,提出天基轻气炮共面清除碎片的方式,并选择轨道高度800 km的圆轨道作为碎片运行轨道进行可行性分析。计算表明,对半径10 cm、厚度1 cm的铝合金圆板碎片(质量211.95 g),使用初速1 km/s、重10 g的黏性弹丸可按任务方案达到清除效果。此外,计算出该参数弹丸对轨道高度800~1200 km的圆轨道上可清除的最大碎片质量为500~825 g,证明轻气炮弹丸对1~10 cm的碎片具有较强的清除能力。最后,分析了以轻气炮为有效载荷的航天器在完成清除碎片任务时的关键技术。     

煤粉粒径分布在气固两相流场中的测试技术研究

针对输送管道内煤粉颗粒的粒径分布宽的特点，用侧向接收散射光的Mie散射方法和Fraunhofer衍射方法作了理论分析和实际测试。利用分子筛和显微镜对被测粒子进行了静态测量，其结果可以作为相对准确的测量标准。研究结果表明，针对细粉分离器内煤粉颗粒的形状、浓度和粒径的分布规律，用衍射测试方法可以达到较高的测试精度，取得较好的测试效果。     

提高电铸局部电沉积速率试验研究

电铸成型是采用离子沉积的方法制造复制件，具有很好的复制精度，因此电铸技术得到了广泛的应用。但由于受极限电流密度等多方面因素的影响，电铸速率一直是制约电铸技术发展的一个瓶颈，许多学者为此做了大量的理论和试验研究，但对如何提高极限电流密度还没有提供一个比较满意的答案，为提高电铸局部电沉积速率，本文在前人工作的基础上，讨论了影响电铸速率的因素，提出了一种新型的电铸方法－喷射式电铸，并通过两组试验分析了局部电沉积速率怀电铸液流量的关系以及局部铸速率与喷嘴口径的关系，试验结果表明，采用喷射式电铸可以大大提高局部极限电流密度，从而使电铸局部电沉积速率有一个较大范围的提高，为将电铸与快速成型结合奠定了试验基础。     

Study on the breakup lengths of free round liquid jets

IntroductionBreakup and atomization of roundliquidjetshad been widely used in internal combustion en-gines,gas turbines,and liquid rocket engines.Recently,with the development of scramjet en-gines and the deepening of fuel atomization re-search,it attract…     

大量程纳米分辨率超精密测径仪

提出了一种新型可以测量孔和轴直径的超精密测量仪，该超精密测径仪主要由炫耀光栅和气浮导轨及红宝石探头组成，采用接触式绝对测量方法。介绍了环境温度的控制和减小环境振动的手段，以保证测量的精度和重复性。这种新型测径系统分辨率可以达到1nm,量程范围可达 0～100mm。     

二次点火发动机最优增程设计与分析

研究了采用二次点火发动机对火箭弹进行增程的最优设计方法与设计原理，用罚函数法把约束条件构成统一的目标函数，再用直接寻优法进行计算，分析了火箭弹倾角、再点火时间及总冲分配等因素对射程的影响。结果表明，二次点火发动机技术可以实现远程火箭弹增程最大的设计要求，且最优发射角对射程影响极大；总冲分配最佳时，总的阻力消耗最小，增程率越大；再点火时间的影响相对较弱。同时还比较了二次点火发动机工作时的火箭弹弹道与一般弹道的区别，及其对阻力和射程的影响。     

Effects of Mach numbers on Magnus induced surface pressure

Experimental and numerical methods were used to investigate the Magnus phenomena over a spinning projectile. The pressure force acting on the surface of a spinning projectile was measured for various cases by employing a relatively novel experimental technique. A set of miniature pressure sensors along with a data acquisition board, battery and storage memory were placed inside a spinning model and the surface pressure were obtained through a remotely controlled system. Circumferential pressures of the model for both rotational and static conditions were obtained at two different free stream Mach numbers of 0.4 and 0.8 and at different angles of attack. The results showed the ability of this new test method to measure the very small Magnus force via surface pressures over the projectile. The results provide a deep insight into the flow structure and illustrate changes in the cross-flow separation locations as a result of rotation. Similar results were obtained by the numerical simulations and were compared with the experimental data.     

Effect of tube-electrode inner diameter on electrochemical discharge machining of nickel-based superalloy

Nickel-based superalloys are widely employed in modern aircraft engines because of their excellent material characteristics, particularly in the fabrication of film cooling holes. How-ever, the high machining requirement of a large number of film cooling holes can be extremely chal-lenging. The hybrid machining technique of tube electrode high-speed electrochemical discharge drilling (TEHECDD) has been considered as a promising method for the production of film cooling holes. Compared with any single machining process, this hybrid technique requires the removal of more complex machining by-products, including debris produced in the electrical discharge machin-ing process and hydroxide and bubbles generated in the electrochemical machining process. These by-products significantly affect the machining efficiency and surface quality of the machined prod-ucts. In this study, tube electrodes in different inner diameters are designed and fabricated, and the effects of inner diameter on the machining efficiency and surface quality of TEHECDD are inves-tigated. The results show that larger inner diameters could effectively improve the flushing condi-tion and facilitate the removal of machining by-products. Therefore, higher material removal efficiency, surface quality, and electrode wear rate could be achieved by increasing the inner diam-eter of the tube electrode.     

正十七烷与正十八烷对航空煤油理化性能及液滴平均直径的影响

讨论了正十七烷与正十八烷(C₁₇,C₁₈)对燃料运动黏度、密度、表面张力理化性能的影响,探究了直链烷烃对SMD(Sauter mean diameter)的影响.将Key's混合规律、Tat混合规律和多项式拟合应用于密度公式的拟合,并将Key's混合规律与对数拟合应用于运动黏度公式的拟合,得出的理化性能拟合公式精度较高;通过测量纯煤油及C₁₇,C₁₈混合油雾化的SMD,实验发现随着直链烷烃的质量分数的增加,混合油的运动黏度增加,SMD也随之增加,雾化效果与纯航空煤油的相比较差,而C₁₈混合油的SMD要比C₁₇混合油要大,并且利用密度、运动黏度的拟合公式对SMD进行预测的偏差小于0.3%.      

大直径螺纹数控加工工艺研究与应用

针对形状结构复杂的某产品上34个M36×3-6H内螺纹加工进行了工艺攻关,提出采用旋风铣的方法,并编制数控加工程序,有效解决了难加工材料大直径内螺纹的加工难题,在此基础上实现了数控加工程序的参数化,理论上可以实现任意直径、任意螺距、任意深度螺纹的加工,并在其他型号产品上得到应用。