捷联惯导系统中陀螺的初始测漂

本文介绍捷联惯导系统中多个陀螺初始常值漂移的测定和补偿。所谓“常值漂移”是指固定不变的漂移和一部分在各次启动时都不相同的并随时间缓慢变化的“随机常值”。本文采用“双位置(测漂)法”可以测出两个角速度陀螺沿载体系X_b,y_b和z_b测量轴的常值漂移。经过仿真证明,这一方法是完全可行的。     

基于四元数估计角速率的陀螺故障定位

当卫星速率积分陀螺的配置冗余度不满足一致性检验条件时，不能单纯利用硬件冗余实现陀螺的故障定位。鉴于角度和角速度敏感器的输出通过卫星运动学相关，本文利用姿态测量敏感器的输出来诊断陀螺故障。首先根据姿态测量敏感器的输出得到卫星姿态四元数，进而根据四元数动力学方程得到粗略的姿态角速度信息，并将此角速度作为输出信息用于对卫星动力学方程的滤波，从而得到较精确的角速度信息，为单冗余度陀螺组件的故障定位提供解析冗余信息。利用四元数方法可以避免出现奇点。仿真结果证明了该方法的有效性。     

电离层峰区的等离子体漂移

根据垂测数据、利用伺服模式讨论了中低纬上空电离层峰区等离子体垂直漂移速度的日变化形态及其随不同季节和不同纬度等的变化规律。揭示了漂移速度的凌晨凹陷与日出凸起现象,指出了可能的形成机制。     

Periodic Error Compensation for Quartz MEMS Gyroscope Drift of INS

In order to improve the navigation accuracy of an inertial navigation system （INS）, composed of quartz gyroscopes, the existing real-time compensation methods for periodic errors in quartz gyroscope drift and the periodic error term relationship between sampled original data and smoothed data are reviewed. On the base of the results, a new compensation method called using former period characteristics to compensate latter smoothness data （UFCL for short） method is proposed considering the INS working characteristics. This new method uses the original data without smoothing to work out an error conversion formula at the INS initial alignment time and then compensate the smoothed data errors by way of the formula at the navigation time. Both theoretical analysis and experimental results demonstrate that this method is able to cut down on computational time and raise the accuracy which makes it a better real-time compensation approach for periodic error terms of quartz micro electronic mechanical system （MEMS） gyroscope＇s zero drift.     

惯组中光纤陀螺温度漂移的二维插值建模研究

光纤陀螺对温度较为敏感,输出受温度及温度变化率影响严重,在实际工作中需要对温度漂移误差进行建模补偿。传统多项式拟合方法如最小二乘法,无法很好地满足精度要求。因此,首先对光纤陀螺工作原理与温度漂移误差产生原理进行分析,得出光纤陀螺温度漂移误差特性。利用传统多项式模型对不同温度下启动的光纤陀螺进行建模补偿,得到补偿后的精度并不理想。利用新的二维插值模型对上述试验重新进行建模补偿,结果表明二维插值模型明显优于多项式模型,光纤陀螺的零偏稳定性由补偿前的0.0153(°)/h提高到0.0051(°)/h,有利于工程上应用。     

新型磁悬浮振动陀螺的设计与分析研究

振动陀螺是一种利用哥氏效应检测角速度的传感器,其谐振子的结构精度和阻尼均匀性限制了陀螺性能的提升。为减小谐振子结构与支撑锚点的影响,提出了一种全新概念的磁悬浮振动陀螺。该陀螺利用电磁悬浮的方法将谐振子悬空,从而简化了谐振子为无支撑锚点的集中质量块,降低了其结构精度要求,消除了机械结构阻尼,最终达到提升陀螺性能的目的。基于经典振动陀螺模型,理论分析了磁悬浮振动陀螺的基本工作原理,并说明了谐振子误差对陀螺性能的影响规律,设计了新型磁悬浮振动陀螺的结构,并对该结构的磁感应强度进行了仿真分析。仿真结果证明,悬浮质量块振动稳定,具有较好的磁场均匀性。最后对陀螺样机进行了测试,其固有频率为20Hz,标度因子约为1.6mV/[(°)/s],测试结果验证了所提磁悬浮振动结构的陀螺效应。     

Application of small-size antennas for estimation of angles of arrival of HF signals scattered by ionospheric irregularities

A modification of the Doppler Interferometry Technique is suggested to enable estimating angles of arrival of comparatively broadband HF signals scattered by random irregularities of the ionospheric plasma with the use of small-size weakly directional antennas. The technique is based on the measurements of cross-spectra phases of the probe radiation recorded at least in three spatially separated points. The developed algorithm has been used to investigate the angular and frequency-time characteristics of HF signals propagating at frequencies above the maximum usable one (MUF) for the direct radio path Moscow-Kharkiv. The received signal spectra show presence of three families of spatial components attributed, respectively, to scattering by plasma irregularities near the middle point of the radio path, ground backscatter signals and scattering of the sounding signals by the intense plasma turbulence associated with auroral activations. It has been shown that the regions responsible for the formation of the third family components are located well inside the auroral oval. The drift velocity and direction of the auroral ionosphere plasma have been determined. The obtained estimates are consistent with the classical conception of the ionospheric plasma convection at high latitudes and do not contradict the results of investigations of the auroral ionosphere dynamics using the SuperDARN network.     

光纤陀螺仪中尖峰脉冲引起漂移 的误差分析及其抑制

首次分析了光纤陀螺仪探测器输出信号中频率固定的尖峰脉冲对光纤陀螺 仪零偏漂移的影响机理,给出了尖峰脉冲影响光纤陀螺仪零偏漂移的误差模型;根据干 涉式数字闭环光纤陀螺仪探测器输出信号的特点,提出了一种基于高速集成模拟开关的 时域选通尖峰脉冲抑制具体实现方法,实验验证了尖峰脉冲引起的零偏漂移大小和理论 分析接近,表明了误差模型的正确性,同时表明该方法能够有效降低尖峰脉冲引起的光 纤陀螺仪零偏漂移。     

一种加速度环境下的温度测量方法

温度-加速度复合环境试验是考察武器、飞行器产品飞行过程中发射、再入等阶段环境适应性能的重要手段.介绍了温度-加速度复合环境试验系统的设计方法,针对高加速度环境下温度采集系统可能出现的温度漂移现象,进行了故障分析,并给出了解决方案.验证试验表明,设计方案可行,相关方法可为复合环境试验可靠性设计提供技术支持.