散射对高温气体-碳黑颗粒混合物辐射传输的影响

基于全光谱k分布(Full spectrum k distribution,FSK)模型、MIE理论和有限体积法(Finite volume method,FVM),构建了均温、均质辐射参与性气体-碳黑颗粒混合物介质热辐射传输模型,并分析了碳黑不同尺寸、不同体积浓度以及介质不同路径长度和不同温度条件下,因忽略碳黑颗粒散射所导致的介质热辐射传输特性(如辐射热流、辐射源项)的计算误差。研究结果表明:体积分数不变,增大粒径,计算误差呈现出先增大后减小的趋势;数密度不变,增大粒径,或者粒径不变,增大体积分数,均将使得计算误差相应增大;粒径、体积分数不变,增大路径长度,或者升高介质温度,均将增大计算误差。通常对于含有大颗粒、高碳黑浓度的辐射参与性气体-碳黑颗粒混合物介质,碳黑颗粒散射不能忽略。     

Topology optimization in lightweight design of a 3D-printed flapping-wing micro aerial vehicle

Topology optimization is an effective method to obtain a lightweight structure that meets the requirements of structural strength. Whether the optimization results meet the actual needs mainly depends on the accuracy of the material properties and the boundary conditions, especially for a tiny Flapping-wing Micro Aerial Vehicle (FMAV) transmission system manufactured by 3D printing. In this paper, experimental and numerical computation efforts were undertaken to gain a reliable topology optimization method for the bottom of the transmission system. First, the constitutive behavior of the ultraviolet (UV) curable resin used in fabrication was evaluated. Second, a numerical computation model describing further verified via experiments. Topology optimization modeling considering nonlinear factors, e.g. contact, friction and collision, was presented, and the optimization results were verified by both dynamic simulation and experiments. Finally, detailed discussions on different load cases and constraints were presented to clarify their effect on the optimization. Our methods and results presented in this paper may shed light on the lightweight design of a FMAV.     

AP聚类改进免疫算法用于航空发动机故障诊断

在免疫算法训练过程中引入近邻传播(AP)聚类与熵权法,对训练样本进行聚类与权值计算,将权值引入免疫算法中样本选择阈值的计算,以解决训练过程采用固定选择阈值所造成的检测器在部分区域过拟合,部分区域欠拟合的问题。结果表明:改进的免疫算法用于典型非线性函数的寻优时,迭代性能均优于传统免疫算法,并在大部分情况下优于粒子群算法与量子遗传算法,在进行某型发动机故障诊断的实例实验时,改进后的算法的诊断准确率达到98.06%,高于传统免疫算法的92.60%。      

涡轮基组合循环发动机分布式控制系统通信网络混合拓扑结构优化方法

涡轮机组合循环(Turbine based combined cycle,TBCC)发动机控制系统通信网络拓扑结构是其分布式控制系统方案设计的重要部分,优化网络拓扑结构可提高发动机推重比和控制系统可靠性。本文基于智能优化算法提出TBCC分布式控制系统网络拓扑结构优化方法。基于图论建立TBCC几何模型和网格模型,以重量和可靠性为优化性能指标,同时考虑发动机表面高温区域以及控制节点的工作可靠性,分别采用粒子群算法和遗传算法优化星形结构中智能中央节点位置、中央节点的环形拓扑结构,获得星形-环形混合拓扑结构。仿真实例表明,基于本文方法优化所得的混合拓扑结构相较于星形集中式控制结构,系统重量降低了51.9%。     

An innovative approach for integrated airline network and aircraft family optimization

The determination of optimal aerial transport networks and their associated flight frequencies is crucial for the strategic planning of airlines, as well as for carrying out market research, to establish target markets, and for aircraft and crew rostering. In addition, optimum airplane types for the selected networks are crucial to improve revenue and to provide reduced operating costs. The present study proposes an innovative approach to determine the optimal aerial transport network simultaneously with the determination of the optimum fleet for that network, composed of three types of airplanes (network and vehicle integrated design). The network profit is maximized. The passenger’s demands between the airports are determined via a gravitational model. An embedded linear programming solution is responsible for obtaining potential optimal network configurations. The optimum fleet combination is determined from a database of candidate aircraft designs via genetic algorithm. A truly realistic airplane representation is made possible thanks to accurate surrogate models for engine and aerodynamics is adopted. An accurate engine deck encompassing a compression map and an innovative engine weight calculation besides an aerodynamical artificial neural network module enable a high degree of accuracy for the mission analysis. The proposed methodology is applied to obtain the optimum network comprised of twenty main Brazilian airports and corresponding fleet.     

对策论在雷达电子战效能评估中的应用

介绍了对策论的基本内容和分析方法,包括对策论所涉及问题的要素和分类.指出了对策论在雷达电子战效能评估中应用的可行性和必要性.分析了电子对抗博弈双方采取不同对抗技术措施的得益矩阵,并在此得益矩阵的基础上,重点研究了对策论在电子对抗效能评估过程中的应用.     

含有任意多个椭圆孔弹性板的应力场计算

本文应用弹性力学的复变函数理论,用多保角变换的方法,导出了含有任意多个椭圆孔的无限大弹性板多复变量应力函数的表达式。每个孔的大小、位置和孔边作用的载荷均为任意指定。板的无限远处作用有和坐标轴方向一致的均匀拉压载荷P_x,P_y和均匀剪切载荷P_(xy)。并在孔边进行复Fourier级数展开,用待定系数法确定应力函数的未知系数,从而计算弹性板的应力场。编制了相应的FORTRAN77标准化程序,进行了考题和算例分析,给出了级数的收敛状况和孔边周向应力的分布图。     

关于疲劳裂纹扩展数学模型的参数寻优

本文通过引入工程设计中的优化方法，分别对室内空气环境下铝合金（ＬＹ１２－ＣＺ）材料疲劳裂纹扩展的数学模型，以及环境条件下（３．５％ＮａＣｌ水溶液浸泡）该材料腐蚀疲劳裂纹扩展的数学模型进行了探讨。在已知标准试样在不同的环境下疲劳裂纹扩展实验ｄａｄＮｉ，ΔＫｉ的条件下，采用优化方法进行参数寻优，可方便地得到与其对应的疲劳裂纹扩展的ｄａｄＮ～ΔＫ最优数学模型     

现代激励理论在规范地方政府行为中的作用研究

分析现代激励理论在研究地方政府行为中的作用，并运用现代激励理论提出了规范地方政府经济行为的若干建议。     

波导分支线定向耦合器计算方法

利用模匹配方法和网络理论分析计算了一种卫星天线系统中常用的波导分支线定向耦合器,计算结果与实验结果非常吻合。该方法为波导分支线定向耦合器提供一种有力的设计手段。它可直接用于设计Ku 波段通信卫星天线的波束形成网络,也可以用来设计各种耦合度的波导分支线定向耦合器。