Influence of thickness and initial groove angle in M–K model on limit strain of 7B04 by considering through-thickness stress

Marciniack–Kuczinski (M–K) model is widely used to predict material’s forming limit curve (FLC). The prediction of FLC traditionally neglected through-thickness normal stress. However, it cannot be neglected in some forming processes. Much work has been done to study the effect of through-thickness normal stress on FLC with constant through-thickness normal stress or constant ratio of through-thickness normal stress and maximum principal stress. In addition, based on Nakazima test process, the ratio of through-thickness normal stress and maximum principal stress has been derived, which was a function of instantaneous thickness and loading path. Here, initial groove angle in M–K model was not considered. In this paper, uniaxial tension tests and Nakazima tests were performed on 7B04 aluminum alloy. Based on Hill 48 yield criterion and M–K model, the prediction model of FLC was established. The increase of thickness can enhance FLC. Meanwhile, it is necessary to consider through-thickness normal stress and initial groove angle in prediction model. On the left side of FLC, the effect of initial groove angle on FLC is weakened by increasing sheet thickness. On the right side of FLC, the effect of initial groove angle on FLC is strengthened by increasing sheet thickness. On the right side of FLC, the relation between limit strain points with different thicknesses is linear under one certain loading path. Thickness has decisive effect on through-thickness normal stress level and the changing trendy of through-thickness normal stress during calculation is different under different stress condition.     

一种基于OPTICS聚类的仅测角导航目标检测算法

仅测角自主导航方法具有设备简单、复杂度低，功耗低的优点，在空间任务中具有广泛的应用前景.针对中远距离下空间目标特征少的特点，提出了一种利用基于OPTICS聚类算法的空间目标检测方法，可用于仅测角导航过程中的目标检测.对原始星图进行预处理提取星点及目标点，并结合星图识别的结果选择部分帧，使用经过改进的OPTICS聚类方法获得目标运动轨迹.最后，使用本文中的算法对软件仿真出的含有目标的高精度星图进行处理验证了算法的可行性.在卫星相对于空间目标抵近过程中，目标检测的水平误差及垂直误差小于0.15°的帧数分别占到了85.4%以及99.6%.相比AVANTI实验中的目标检测方法，减少了在轨任务中相关参数的调节，进一步提升了算法的自主性.     

Fault mode probability factor based fault-tolerant control for dissimilar redundant actuation system

This paper presents a Fault Mode Probability Factor (FMPF) based Fault-Tolerant Control (FTC) strategy for multiple faults of Dissimilar Redundant Actuation System (DRAS) composed of Hydraulic Actuator (HA) and Electro-Hydrostatic Actuator (EHA). The long-term service and severe working conditions can result in multiple gradual faults which can ultimately degrade the system performance, resulting in the system model drift into the fault state characterized with parameter uncertainty. The paper proposes to address this problem by using the historical statistics of the multiple gradual faults and the proposed FMPF to amend the system model with parameter uncertainty. To balance the system model precision and computation time, a Moving Window (MW) method is used to determine the applied historical statistics. The FMPF based FTC strategy is developed for the amended system model where the system estimation and Linear Quadratic Regulator (LQR) are updated at the end of system sampling period. The simulations of DRAS system subjected to multiple faults have been performed and the results indicate the effectiveness of the proposed approach.     

PBT弹性体微相分离及对其力学性能的影响研究

为了获得微相分离对宽温PBT叠氮聚醚弹性体力学性能的影响规律,用红外光谱分析法(FT-IR)和动态热力学分析法(DMA)研究了PBT叠氮聚醚弹性体产生微相分离的机理和影响因素。用调节硬段含量、交联参数的方法调控其微相分离,控制适当的微相分离程度可显著改善推进剂的力学性能。研究结果表明:在二元醇扩链的弹性体体系中,当硬段含量约为15%时,弹性体发生相对最大比例的微相分离,体现出较佳的综合力学性能。通过微相分离的调控可获得宽温范围内综合力学性能较好的叠氮聚醚推进剂用粘合剂基体材料。     

紧缩场测试扫描架平面度控制系统研制

扫描架是紧缩场现场校准系统的关键测试设备。扫描架扫描平面度是影响校准准确度的关键指标。本文针对自研的扫描区域为φ6m的大型极化扫描架，设计了一套扫描架平面度实时补偿系统。该实时补偿系统可以实时检测扫描架扫描平面相对于基准平面的位置偏差，并通过伺服补偿机构完成补偿。测试结果表明该实时补偿系统可以准确、快速完成平面度的补偿，与半实时补偿方式相比具有更高的效率及精度。目前，该系统已成功应用于紧缩场现场校准。     

一种基于多点测距信息的复合制导方法

分析探讨了一种用于提高弹道式导弹对目标命中精度的复合制导方案，提出了通过进行多点测距，利用状态转移矩阵方法，来估计导弹落点偏差和末修级起控点飞行状态参数，然后再按照需要的速度进行末修级导引控制的复合制导方案，并通过仿真计算分析论证了该方法的可行性。     

含有任意多个椭圆孔弹性板的应力场计算

本文应用弹性力学的复变函数理论,用多保角变换的方法,导出了含有任意多个椭圆孔的无限大弹性板多复变量应力函数的表达式。每个孔的大小、位置和孔边作用的载荷均为任意指定。板的无限远处作用有和坐标轴方向一致的均匀拉压载荷P_x,P_y和均匀剪切载荷P_(xy)。并在孔边进行复Fourier级数展开,用待定系数法确定应力函数的未知系数,从而计算弹性板的应力场。编制了相应的FORTRAN77标准化程序,进行了考题和算例分析,给出了级数的收敛状况和孔边周向应力的分布图。     

HML系统在商店偏好决策模型中的应用研究

对混合式机器学习系统（HML）进行了全面系统的介绍，并将其运用于服装消费商店偏好决策行为的研究中。采用上海统计局家庭调查网络，对300户家庭进行抽样分析后发现，服装消费商店偏好的主要影响因素是地区、季节、丈夫和妻子的学历、职业以及子女性别。在此基础上，将HML分析所得的结论与传统的研究方法和结果进行了系统比较：从方法上来看，因为属性变量包含间断变量和连续变量两种，因此传统统计分析要运用两种不同的检测方法对影响因素的相关性作出判断，结果需要经过统计学分析，才能得到结论；而HML分析结果比较直观和简单，便于理解。     

利用热源温度场迭加法诊断持续点热源的强度及位置

可重复使用运载器的防热瓦故障会使航天器的局部结构产牛热源，并在结构中形成温度场。应用热源温度场迭加法的解函数，解得结构温度历程，然后据此温度的变化率趋势判断出热源位置，在此基础上依据多点测最值构造出辨识参数用于热强度识别，通过对一薄壁结构模型算例的计算仿真，证明了本文所提方法的有效性。论文工作为进一步开展热源诊断技术研究，提供了可资工程实践应用的数值算法体系以及有益的数值计算结论。     

美国MTS公司应用软件在测试上的应用

介绍了用美国ＭＴＳ公司的平面应变断裂韬度测试软件，对ＴＣ４合金进行ＫＩＣ测试的过程及结果。