PANIC – A surface science package for the in situ characterization of a near-Earth asteroid

This paper presents the results of a mission concept study for an autonomous micro-scale surface lander also referred to as PANIC – the Pico Autonomous Near-Earth Asteroid In Situ Characterizer. The lander is based on the shape of a regular tetrahedron with an edge length of 35 cm, has a total mass of approximately 12 kg and utilizes hopping as a locomotion mechanism in microgravity. PANIC houses four scientific instruments in its proposed baseline configuration which enable the in situ characterization of an asteroid. It is carried by an interplanetary probe to its target and released to the surface after rendezvous. Detailed estimates of all critical subsystem parameters were derived to demonstrate the feasibility of this concept. The study illustrates that a small, simple landing element is a viable alternative to complex traditional lander concepts, adding a significant science return to any near-Earth asteroid (NEA) mission while meeting tight mass budget constraints.     

Investigation of the steam-cooled blade in a steam turbine cascade

With the increasing demand for electricity,an efficiency improvement and thereby reduced CO2 emissions of the coal-fired plants are expected in order to reach the goals set in the Kyoto protocol.It can be achieved by a rise of the process parameters.Currently,live steam pressures and temperatures up to 300 bars and 923 K are planned as the next step.Closed circuit steam cooling of blades and vanes in modern steam turbines is a promising technology in order to establish elevated live steam temperatures in future steam turbine cycles.In this paper,a steam-cooled test vane in a cascade with external hot steam flow is analyzed numerically with the in-house code CHTflow.A parametric analysis aiming to improve the cooling effectiveness is carried out by varying the cooling mass flow ratio.The results from two investigated cases show that the steam cooling technique has a good application potential in the steam turbine.The internal part of the vane is cooled homogeneously in both cases.With the increased cooling mass flow rate,there is a significant improvement of cooling efficiency at the leading edge.The results show that the increased cooling mass flow ratio can enhance the cooling effectiveness at the leading edge.With respect to trailing edge,there is no observable improvement of cooling effectiveness with the increased cooling mass flow.This implies that due to the limited dimension at the trailing edge,the thermal stress cannot be decreased by increasing the cooling mass flow rate.Therefore,impingement-cooling configuration at the trailing edge might be a solution to overcome the critical thermal stress there.It is also observed that the performance of the cooling effective differs on pressure side and suction side.It implicates that the equilibrium of the cooling effectiveness on two sides are influenced by a coupled relationship between cooling mass flow ratio and hole geometry.In future work,optimizing the hole geometry and cooling steam supply conditions might be the solutions for an equivalent cooling effectiveness along whole profile.      

A small mission for in situ exploration of a primitive binary near-Earth asteroid

We present a concept for a challenging in situ science mission to a primitive, binary near-Earth asteroid. A sub-400-kg spacecraft would use solar electric propulsion to rendezvous with the C-class binary asteroid (175706) 1996 FG3. A campaign of remote observations of both worlds would be followed by landing on the ∼1 km diameter primary to perform in situ measurements. The total available payload mass would be around 34 kg, allowing a wide range of measurement objectives to be addressed. This mission arose during 2004 from the activities of the ad-hoc Small Bodies Group of the DLR-led Planetary Lander Initiative. Although the particular mission scenario proposed here was not studied further per se, the experience was carried over to subsequent European asteroid mission studies, including first LEONARD and now the Marco Polo near-Earth asteroid sample return proposal for ESA’s Cosmic Vision programme. This paper may thus be of interest as much for insight into the life cycle of mission proposals as for the concept itself.     

边界层吸气对压气机叶栅角区分离损失的控制

压气机角区的大范围回流通常会引起叶片通道中的三维阻塞现象,并伴随有强烈的掺混流动损失。采用德国航空航天中心(DLR)开发的TRACE程序,在其推进技术研究所的高速压气机叶栅试验台(包含5个NACA65K48直叶片)上,研究了位于端壁上的边界层吸气措施——叶片弦中近尾缘吸气槽(MTE)对该直压气机叶栅通道的角区分离进行控制,减小二次流动损失,进而削弱其对总损失的影响。通过基于定常雷诺平均Navier-Stokes(RANS)方法的数值模拟研究与相应的试验研究对比,端壁边界层吸气能够较好地重新组织角区气流流动,减弱附着于叶片吸力面尾缘的集中脱落涡,使得角区分离涡强度显著降低,由此引起的二次流损失也明显降低,与无吸气状态相比最大降幅可达81.2%;在设计状态下采用吸气流量率为1%的MTE,总压损失有很大程度的降低:在数值计算中,降幅为15.2%;试验测量中为9.7%。     

Mupus – A Thermal and Mechanical Properties Probe for the Rosetta Lander Philae

MUPUS, the multi purpose sensor package onboard the Rosetta lander Philae, will measure the energy balance and the physical parameters in the near-surface layers – up to about 30 cm depth- of the nucleus of Rosetta’s target comet Churyumov-Gerasimenko. Moreover it will monitor changes in these parameters over time as the comet approaches the sun. Among the parameters studied are the density, the porosity, cohesion, the thermal diffusivity and conductivity, and temperature. The data should increase our knowledge of how comets work, and how the coma gases form. The data may also be used to constrain the microstructure of the nucleus material. Changes with time of physical properties will reveal timescales and possibly the nature of processes that modify the material close to the surface. Thereby, the data will indicate how pristine cometary matter sampled and analysed by other experiments on Philae really is.     

Measurement and stability of the pointing of the BepiColombo Laser Altimeter under thermal load

The BepiColombo Laser Altimeter (BELA) has been selected to fly on ESA?s BepiColombo mission to Mercury. The instrument will be the first European laser altimeter designed for interplanetary flight. This paper describes the setup used to characterize the angular movements of BELA under the simulated environmental conditions that the instrument will encounter when orbiting Mercury. The system comprises a laser transmitter and a receiving telescope, which can move with respect to each other under thermal load. Tests performed using the Engineering Qualification Model show that the setup is accurate enough to characterize angular movements of the instrument components to an accuracy of ≈10 μrad. The qualification instrument is thermally stable to operate during all mission phases around Mercury proving that the transmitter and receiver sections will remain within the alignment requirements during its mission.