导航卫星中断频次的分析方法

面向导航卫星中断频次的定量分析需求,该文分析导航卫星中断产生的主要原因,给出中断频次分析的流程,并针对分析过程中的三个关键问题,研究提出具体实施方法,包括通过相关性分析快速定位底层中断事件,通过中断树建立指标分析模型,并融合在轨数据、地面试验数据快速预估得到底层功能异常率等。最后通过示例进一步说明中断频次分析过程。该文方法已应用于北斗导航卫星工程。     

Orbit-attitude-vibration coupled dynamics of tethered solar power satellite

A new orbit-attitude-vibration coupled dynamic model of the tethered solar power satellite (Tethered SPS) is established based on absolute nodal coordinate formulation. The Hamilton’s equation of the system is derived by introducing generalized momentum through Legendre transformation. The correctness of the proposed model is verified by an example. The dynamic characteristics of the Tethered SPS are studied using the symplectic Runge-Kutta method. Simulation results show that the orbital radius and the total energy of the system are well preserved. The attitude of the system is unstable when the mass of the bus system is small. However, the attitude stability is dependent on some other parameters of the system, which requires further studies. It is also found that the average tether force/deformation can be roughly estimated by simplifying the solar panel as a particle. The proposed model can be used to study the orbit-attitude-vibration coupled dynamics and control problems.     

一种基于OPTICS聚类的仅测角导航目标检测算法

仅测角自主导航方法具有设备简单、复杂度低，功耗低的优点，在空间任务中具有广泛的应用前景.针对中远距离下空间目标特征少的特点，提出了一种利用基于OPTICS聚类算法的空间目标检测方法，可用于仅测角导航过程中的目标检测.对原始星图进行预处理提取星点及目标点，并结合星图识别的结果选择部分帧，使用经过改进的OPTICS聚类方法获得目标运动轨迹.最后，使用本文中的算法对软件仿真出的含有目标的高精度星图进行处理验证了算法的可行性.在卫星相对于空间目标抵近过程中，目标检测的水平误差及垂直误差小于0.15°的帧数分别占到了85.4%以及99.6%.相比AVANTI实验中的目标检测方法，减少了在轨任务中相关参数的调节，进一步提升了算法的自主性.     

联邦学习安全与隐私保护综述

联邦学习是一种新型的分布式学习框架，它允许在多个参与者之间共享训练数据而不会泄露其数据隐私。但是这种新颖的学习机制仍然可能受到来自各种攻击者的前所未有的安全和隐私威胁。本文主要探讨联邦学习在安全和隐私方面面临的挑战。首先，本文介绍了联邦学习的基本概念和威胁模型，有助于理解其面临的攻击。其次，本文总结了由内部恶意实体发起的3种攻击类型，同时分析了联邦学习体系结构的安全漏洞和隐私漏洞。然后从差分隐私、同态密码系统和安全多方聚合等方面研究了目前最先进的防御方案。最后通过对这些解决方案的总结和比较，进一步讨论了该领域未来的发展方向。     

先进战斗机过失速机动大气数据融合估计方法

可控的过失速机动是先进战斗机超机动性能的重要标志，飞机飞行包线的扩大已超出传统的大气数据系统测量范围，可靠的迎角、侧滑角、总压、静压等飞行大气数据是制约先进战斗机过失速机动中飞行控制的关键因素。以中国推力矢量验证机为对象，基于过失速机动飞行试验的数据，开展大气参数估计与验证研究。结合过失速机动的时间与空间特性，研究了基于风速、地速、空速矢量和惯性姿态、导航参数的大气参数融合计算方法；针对过失速大迎角状态下飞机周围气流非定常、模型非线性导致的融合大气参数误差的复杂特性，进一步构建深度神经网络，对机动状态融合迎角、侧滑角的强非线性误差进行拟合。仿真和飞行试验表明：该方法可在大迎角飞行状态下实现主要大气参数的融合估计，过失速机动过程中融合迎角误差优于2.3°，融合得到的大气参数可为过失速大迎角机动飞行控制提供可靠的大气参数状态反馈。     

A survey of safety separation management and collision avoidance approaches of civil UAS operating in integration national airspace system

Recent years have witnessed a booming of the industry of civil Unmanned Aircraft System (UAS). As an emerging industry, the UAS industry has been attracting great attention from governments of all countries and the aviation industry. UAS are highly digitalized, informationized, and intelligent; therefore, their integration into the national airspace system has become an important trend in the development of civil aviation. However, the complexity of UAS operation poses great challenges to the traditional aviation regulatory system and technical means. How to prevent collisions between UASs and between UAS and manned aircraft to achieve safe and efficient operation in the integrated operating airspace has become a common challenge for industry and academia around the world. In recent years, the international community has carried out a great amount of work and experiments in the air traffic management of UAS and some of the key technologies. This paper attempts to make a review of the UAS separation management and key technologies in collision avoidance in the integrated airspace, mainly focusing on the current situation of UAS Traffic Management (UTM), safety separation standards, detection system, collision risk prediction, collision avoidance, safety risk assessment, etc., as well as an analysis of the bottlenecks that the current researches encountered and their development trends, so as to provide some insights and references for further research in this regard. Finally, this paper makes a further summary of some of the research highlights and challenges.     

Estimating inter-system biases for tightly combined Galileo/BDS/GPS RTK

The overlapping carrier frequencies L1/E1, L5/E5a and B2/E5b from GPS/Galileo/BDS allow inter-system double-differencing of observations, which shows a clear advantage over differencing of the observations of each constellation independently. However, the inter-system biases destroy the integer nature of the inter-system double-differencing ambiguities. Two methods of direct rounding and parameter estimation are used to determine the ISB value. By analyzing data collected from Curtin University from 2015 to 2018, the phase and code inter-system bias (ISB) are related to the receiver type, firmware version and the selected overlapping frequency. Upgrade of receiver firmware version results in changes of ISB values. For example, the upgrade of Javad firmware in Dec, 15, 2017 causes the difference of 0.5 cycles ISB between BDS GEO and non-GEO satellites. By comparing the three dynamic models which include white noise process, random walk process, and random constant in the parameter estimation method, the ISB determined by the random constant model is consistent with the value obtained by the direct rounding method. After the calibration of ISBs, the performances of tightly combined positioning are assessed. The success rate of ambiguity resolution and accuracy of positioning for the tight combination (TC) are significantly improved in comparison with that for the loose combination (LC) over short baselines. For L5/E5a, on which only few satellites can be observed, the maximum increase in success rates of ambiguity resolution can reach 31.7%, i.e., from 54.9% of LC to larger than 86.6% of TC, and the positioning accuracies can even be increased by 0.13 m, i.e., from 0.208 of LC to 0.074 m of TC in East direction for the mix-receiver TRIMBLE NETR9-SEPT POLARX4 in 2018.     

Fault mode probability factor based fault-tolerant control for dissimilar redundant actuation system

This paper presents a Fault Mode Probability Factor (FMPF) based Fault-Tolerant Control (FTC) strategy for multiple faults of Dissimilar Redundant Actuation System (DRAS) composed of Hydraulic Actuator (HA) and Electro-Hydrostatic Actuator (EHA). The long-term service and severe working conditions can result in multiple gradual faults which can ultimately degrade the system performance, resulting in the system model drift into the fault state characterized with parameter uncertainty. The paper proposes to address this problem by using the historical statistics of the multiple gradual faults and the proposed FMPF to amend the system model with parameter uncertainty. To balance the system model precision and computation time, a Moving Window (MW) method is used to determine the applied historical statistics. The FMPF based FTC strategy is developed for the amended system model where the system estimation and Linear Quadratic Regulator (LQR) are updated at the end of system sampling period. The simulations of DRAS system subjected to multiple faults have been performed and the results indicate the effectiveness of the proposed approach.     

Implementation of tactical maneuvers with maneuver libraries

This study creates and combines the general maneuver libraries for fixed-wing aircraft to implement tactical maneuvers. First, the generalized maneuver libraries are established by analyzing the characteristics of tactical maneuvers required in battlefields. The 7th order polynomial is applied to both the creation of the maneuver libraries and the generation of the trajectories or flight paths for modal inputs. To track the desired trajectory, we design the Attitude Command Attitude Hold (ACAH) system and the Rate Command Rate Hold (RCRH) system using Model Following Controller (MFC). Moreover, the Line-of-Sight (LOS) guidance law is designed. In particular, the CONDUIT® is employed to optimize the gains so that the control systems meet the aircraft Handling Qualities (HQ) criteria. Finally, flight simulations are performed for the longitudinal loop, immelmann-turn, and climb-slalom-descent maneuvers to verify that tactical aggressive maneuvers are realizable via the combination of maneuver libraries. This study can contribute to the development of flight techniques for aircraft tactical maneuvers and to the revision of air force operational manuals.     

Topology optimization in lightweight design of a 3D-printed flapping-wing micro aerial vehicle

Topology optimization is an effective method to obtain a lightweight structure that meets the requirements of structural strength. Whether the optimization results meet the actual needs mainly depends on the accuracy of the material properties and the boundary conditions, especially for a tiny Flapping-wing Micro Aerial Vehicle (FMAV) transmission system manufactured by 3D printing. In this paper, experimental and numerical computation efforts were undertaken to gain a reliable topology optimization method for the bottom of the transmission system. First, the constitutive behavior of the ultraviolet (UV) curable resin used in fabrication was evaluated. Second, a numerical computation model describing further verified via experiments. Topology optimization modeling considering nonlinear factors, e.g. contact, friction and collision, was presented, and the optimization results were verified by both dynamic simulation and experiments. Finally, detailed discussions on different load cases and constraints were presented to clarify their effect on the optimization. Our methods and results presented in this paper may shed light on the lightweight design of a FMAV.