Orbit-attitude-vibration coupled dynamics of tethered solar power satellite

A new orbit-attitude-vibration coupled dynamic model of the tethered solar power satellite (Tethered SPS) is established based on absolute nodal coordinate formulation. The Hamilton’s equation of the system is derived by introducing generalized momentum through Legendre transformation. The correctness of the proposed model is verified by an example. The dynamic characteristics of the Tethered SPS are studied using the symplectic Runge-Kutta method. Simulation results show that the orbital radius and the total energy of the system are well preserved. The attitude of the system is unstable when the mass of the bus system is small. However, the attitude stability is dependent on some other parameters of the system, which requires further studies. It is also found that the average tether force/deformation can be roughly estimated by simplifying the solar panel as a particle. The proposed model can be used to study the orbit-attitude-vibration coupled dynamics and control problems.     

基于CFD高精度算法的雷电电磁场研究

雷电空间电磁场一直是电磁领域研究的热门，成熟的算法例如有限时域差分法（FDTD），传输线矩阵法（TLM）以及频域的矩量法（MoM）在计算雷电问题方面都有广泛的应用。由于计算流体力学（CFD）中的Euler方程与电磁学中的Maxwell方程有着相同的守恒形式，而且采用间断伽辽金方法（DG）已经在流场问题上得到广泛的尝试，因此引入了基于计算流体力学的DG方法来离散时域Maxwell方程，并采用网格分区并行技术加速计算，使用基于DG的圆球雷达散射截面积（RCS）算例进行测试，数值结果一致表明DG算法在求解电磁场问题上的可行性，之后通过计算一段近场雷电通道的电场分布并与解析解、某算法仿真解对比，数据基本吻合，说明该方法适合于雷电电磁场的计算。     

Cutting path-dependent machinability of SiCp/Al composite under multi-step ultra-precision diamond cutting

Particle-tool interactions, which govern the synergetic deformation of SiC particle reinforced Al matrix composites under mechanical machining, strongly depend on the geometry of particle position residing on cutting path. In the present work, we investigate the influence of cutting path on the machinability of a SiCp/Al composite in multi-step ultra-precision diamond cutting by combining finite element simulations with experimental observations and characterization. Be consistent with experimentally characterized microstructures, the simulated SiCp/Al composite is considered to be composed of randomly distributed polygonally-shaped SiC particles with a volume fraction of 25vol%. A multi-step cutting strategy with depths of cut ranging from 2 to 10 μm is adopted to achieve an ultimate depth of cut of 10 μm. Intrinsic material parameters and extrinsic cutting conditions utilized in finite element simulations of SiCp/Al cutting are consistent with those used in corresponding experiments. Simulation results reveal different particle-tool interactions and failure modes of SiC particles, as well as their correlations with machining force evolution, residual stress distribution and machined surface topography. A detailed comparison between numerical simulation results and experimental data of multi-step diamond cutting of SiCp/Al composite reveals a substantial impact of the number of cutting steps on particle-tool interactions and machined surface quality. These findings provide guidelines for achieving high surface finish of SiCp/Al composites by ultra-precision diamond cutting.     

A novel satellite image encryption algorithm based on hyperchaotic systems and Josephus problem

With the rapid growth of the number of Earth observation satellite (EOS) supporting critical applications, it is required to improve the security techniques to protect the sensitive data and images during the transmission between the satellites and the ground stations. This paper introduces a new satellite image encryption algorithm based on the Linear Feedback Shift Register (LFSR) generator, SHA 512 hash function, hyperchaotic systems, and Josephus problem. LFSR generates a matrix that is used to construct the 512-bits value of the hash function. These bits are used to set the initial values and parameters of the proposed encryption algorithm. Firstly, the six dimensions (6-D) hyperchaotic system is divided into three parts, where every two equations are considered as one part. Secondly, the 1-D hyperchaotic logistic-tent system is considered as the controller to select one part. The selected part is used to generate a matrix that is XORed with the original image. Thirdly, the scrambling operation by Josephus sequences is applied to the output of the previous step by scrambling the rows and the columns according to the selected part to produce the pre-encrypted image. Finally, if the number of iterations is less than the required number which is considered as a parameter of the secret key, the previous operations will be repeated in the pre-encrypted image; otherwise, the pre-encrypted image is considered as the final cipher image. Experimental and analyses results show that the proposed algorithm has good performance in terms of high level of security, large enough key-space, tolerance to Single Event Upsets (SEU) as well as low time complexity.     

A novel framework for liquid propellant engine’s cooling system design by sensitivity analysis based on RSM and multi-objective optimization using PSO

One of the challenges of combustion chamber and nozzle design in a Liquid Propellant Engine (LPE) is to predict the behavior and performance of the cooling system. Therefore, while designing, the optimization of the cooling system is always of great importance. This paper presents the multi-objective optimization of the LPE’s cooling system. To this end, a novel framework has been developed, resulting from the application of the Response Surface Method (RSM) and the correlation coefficients matrix, sensitivity analysis and the The Particle Swarm Optimization (PSO). based on this method, the input variables, constraints, objective functions, and their surfaces were identified. In terms of multi-optimization algorithms, RSM and PSO are utilized to get global optimum. In conclusion, the methodology capability is to optimize the LPE’s cooling system, 6 percentage increase in total heat transfer and 7 bar decrease cooling system pressure loss, which resulted in a 1.2-seconds increase in the specific impulse of the engine.     

导航卫星中断频次的分析方法

面向导航卫星中断频次的定量分析需求,该文分析导航卫星中断产生的主要原因,给出中断频次分析的流程,并针对分析过程中的三个关键问题,研究提出具体实施方法,包括通过相关性分析快速定位底层中断事件,通过中断树建立指标分析模型,并融合在轨数据、地面试验数据快速预估得到底层功能异常率等。最后通过示例进一步说明中断频次分析过程。该文方法已应用于北斗导航卫星工程。     

Solar sailing in realistic mode,based on a locally-optimal control laws

Ballistic design of solar sailing missions in the solar system is composed of defining the design parameters, the control programs, and the trajectories that provide performance goals of a flight. The use of a solar sail spacecraft imposes specific restrictions on mission parameters that include the degradation limit on the flight duration, the maximum temperature of solar sail's surface, the minimum distance from the Sun, the maximum angular velocity of the spacecraft's rotation and others.Many authors considered the impact of these restrictions on the design of the mission separately, but they used a sophisticated method of finding the exact optimal motion control or applied the most straightforward laws of motion control. This paper uses local-optimal control laws at the complete mathematical models of motion and functioning of solar sail spacecraft to describe a technique of designing interplanetary missions. The described method avoids the need to obtain an accurate optimal solution to the control problem and does not cause significant computational difficulties.     

详细化学反应机理对预混丙烷钝体熄火模拟影响

航空发动机熄火预测是重要关键问题之一，湍流和化学反应的非线性相互作用使预测非常困难。本文采用大涡模拟（LES）对湍流进行高精度模拟，采用概率密度函数输运方程湍流燃烧模型（TPDF）耦合JL4、Z66和H73三种化学反应机理，对预混丙烷钝体熄火现象和规律进行研究。JL4的反应机理最简单，反应释热快，局部放热高，火焰宽度大，火焰两侧温度梯度大，燃烧更加趋于稳定，无法模拟出熄火状态。H73机理绝热火焰温度低，火焰温度低，回流区中部OH含量高；在近熄火状态，大量CO被氧化，释放热量过高导致无法模拟出熄火现象。Z66机理可以模拟出火焰正常状态，在低当量比下也可以模拟出熄火状态。本文算例中，局部Da数大于1的区域超过35%则会发生熄火。     

Initiation characteristics of oblique detonation waves from a finite wedge under argon dilution

In this paper, the flow field characteristics of Oblique Detonation Waves (ODWs) induced by a finite wedge under argon dilution are studied by solving the Euler equations with a detailed chemical model of hydrogen and air. First, the effects of the expansion waves, argon concentration, geometric parameters, and Mach number on the ODW are discussed. The results show that the changes of these parameters may make the oblique detonation not be initiated. Then, the ODW initiation criterion of the finite wedge is summarized, as the characteristic length of the induction zone L_C and the characteristic length of the oblique wedge L_W meet the condition L_C/L_W < 1, the initiation of the ODW occurs; otherwise, it does not occur. What’s more, the Constant Volume Combustion (CVC) theory is applied to study the characteristic length of induction zone. It is found that CVC theory is more suitable for the “smooth transition” type of ODW flow field, the theoretical and numerical characteristic length in induction regions are in good agreement. This work is of great significance for the design of oblique detonation engines for hypersonic vehicles.     

固体运载火箭级间热分离仿真气体模型研究

目前,计算流体力学和飞行力学耦合仿真是模拟运载火箭级间分离较为流行的方法,而发动机内外流动建模则是运用该方法的关键。工程上,常用的方法是将发动机燃气与外部大气当作同一种气体组分处理,未考虑内外流动的多组分与燃烧效应。分析了化学非平衡流模型、双组分气体模型和常规单组分气体模型在火箭级间热分离流场计算中的适用性。化学非平衡流模型由于过高的计算消耗,不适用于火箭研制工程中大规模的参数化研究。而热化学等级较低的双组分气体和单组分气体模型由于计算量较低,具有较好的工程适用性。双组分气体模型计入了火箭燃气的特性,计算消耗远低于化学非平衡计算,且能够较好地预测火箭级间段的流动分离,在计算效率和计算保真度之间做出了较好的平衡,未来在工程研究中有较大的应用潜力。