弹载变转速定量泵高动态压力控制特性分析

传统弹载电液伺服系统的液压能源采用有刷直流电机驱动恒压变量泵的方式，泵源压力在导弹飞行过程中设定值恒定，但在平飞段过程长、负载小，对能源压力需求低，造成弹上能源总利用率不高的问题，提出无刷直流电机驱动小排量液压泵的压力控制泵源的设计，在低气动负载阶段适当降低系统压力，进而降低节流损失与泄漏量，提高能量利用率。分析了变转速定量泵的流量压力特性曲线，通过建立基于变转速压力控制泵源的位置电液伺服系统数学模型与仿真模型，分析了变转速定量泵压力控制系统在典型工况下的位置跟踪、系统压力变化与能量利用效率，验证了压力控制系统能够在导弹平飞段保证位置伺服系统跟踪正常的前提下，能有效提高系统效率，证明了变转速定量泵压力控制系统的有效性与可行性。     

高背压等离子点火器及其液体燃料点火特性实验研究

航天应用的液体火箭发动机及燃烧型加热器燃烧室室压高、燃料流量大、温度低、有重复启动需求，实现安全可靠点火的难度较大。针对这些需求，研究了一种采用高背压设计的电弧等离子体点火器。实验研究了Ar，N₂气体工质在高进气压力下的伏安特性，发现N₂在宽压力范围内适用于点火。发射光谱分析表明，在高达数MPa的进气压力下，Ar，N₂等离子体射流电子密度符合局部热力学平衡判据（LTE判据），点火能量集中。N₂等离子体整体温度低于Ar，但阳极喷口附近温度高于Ar，N₂等离子体射流火焰长，卷吸沿程空气造成射流平均温度偏低，但有助于低温液体推进剂的蒸发混合和强化点火。等离子体射流引起了臭氧和氮氧化物的形成，具有促进点火和化学反应的作用。背压提高引起电源输出电压升高，提高供气压力和电流，有助于点火器在高背压环境中稳定电压。燃烧型空气加热器燃烧室的点火实验发现，采用N₂等离子体喷注面中心点火，可以在短时间内完成酒精-空气和酒精-液氧-空气的点火，最高燃烧室室压接近5MPa时，点火器仍能稳定工作，多次使用电极烧蚀不明显，在液体火箭发动机的重复可靠点火方面具有很好的应用前景。     

An empirical solar radiation pressure model for satellites moving in the orbit-normal mode

We present a family of empirical solar radiation pressure (SRP) models suited for satellites orbiting the Earth in the orbit normal (ON) mode. The proposed ECOM-TB model describes the SRP accelerations in the so-called terminator coordinate system. The choice of the coordinate system and the SRP parametrization is based on theoretical assumptions and on simulation results with a QZS-1-like box-wing model, where the SRP accelerations acting on the solar panels and on the box are assessed separately. The new SRP model takes into account that in ON-mode the incident angle of the solar radiation on the solar panels is not constant like in the yaw-steering (YS) attitude mode. It depends on the elevation angle of the Sun above the satellite’s orbital plane. The resulting SRP vector acts, therefore, not only in the Sun-satellite direction, but has also a component normal to it. Both components are changing as a function of the incident angle. ECOM-TB has been used for precise orbit determination (POD) for QZS-1 and BeiDou2 (BDS2) satellites in medium (MEO) and inclined geosynchronous Earth orbits (IGSO) based on IGS MGEX data from 2014 and 2015. The resulting orbits have been validated with SLR, long-arc orbit fits, orbit misclosures, and by the satellite clock corrections based on the orbits. The validation results confirm that—compared to ECOM2—ECOM-TB significantly (factor 3–4) improves the POD of QZS-1 in ON-mode for orbits with different arc lengths (one, three, and five days). Moderate orbit improvements are achieved for BDS2 MEO satellites—especially if ECOM-TB is supported by pseudo-stochastic pulses (the model is then called ECOM-TBP). For BDS2 IGSOs, ECOM-TB with its 9 SRP parameters appears to be over-parameterized. For use with BDS2 IGSO spacecraft we therefore developed a minimized model version called ECOM-TBMP, which is based on the same axis decomposition as ECOM-TB, but has only 2 SRP parameters and is supported by pseudo-stochastic parameters, as well. This model shows a similar performance as ECOM-TB with short arcs, but an improved performance with (3-day) long-arcs. The new SRP models have been activated in CODE’s IGS MGEX solution in Summer 2018. Like the other ECOM models the ECOM-TB derivatives might be used together with an a priori model.     

四旋翼倾转飞行器操纵冗余设计

建立了四旋翼倾转飞行器旋翼、机翼、机身的非线性气动模型和飞行动力学模型,并在Matlab/Simulink环境下搭建了仿真模型,根据仿真模型计算各个操纵面的操纵效率,确定了不同状态下各个通道需要用到的操纵方式,结合飞行动力学模型和操纵方式,在纵向通道上进行了全包线的配平计算,表明了操纵策略的可行性。     

Effect of bristle pack position on the rotordynamic characteristics of brush-labyrinth seals at various operating conditions

Over the last few decades, the research on the effect of bristle pack position on the rotordynamic characteristics of the brush-labyrinth seals is not sufficient. To this end, two kinds of brush-labyrinth seals for the bristle pack element installed upstream of the labyrinth teeth named BSU and installed downstream of the labyrinth teeth called BSD were used to investigate the effect of bristle pack position on the rotordynamic characteristics of the brush-labyrinth seals. Using the numerical model combining the porous medium model and the whirling rotor method, the rotordynamic characteristics of the BSU and BSD at various operating conditions including four kinds of pressure ratios, five kinds of inlet preswirl speeds and four kinds of rotor spinning speeds were conducted. The obtained results show that the effects of operating conditions on rotordynamic coefficients for the different seal configurations are different. The direct stiffness, cross-coupled stiffness and direct damping of the BSU are lower than those of the BSD. The rotordynamic coefficients of the BSU are more insensitive to the operating conditions variation. From the perspective of the seal stability, the BSU is a better brush-labyrinth seal configuration at high pressure ratio, high positive preswirl or high rotor spinning speed conditions. While in the case of low pressure ratio, low positive preswirl or low rotor spinning speed conditions, the BSD is a better choice.     

直升机后缘襟翼驱动器迟滞现象仿真与抑制

直升机后缘襟翼多采用压电驱动器作为驱动元件，但是在使用过程中压电驱动器迟滞会对其振动控制性能产生不利影响，因此针对压电驱动器迟滞开展了迟滞建模与抑制研究。通过实验研究了压电驱动器在不同驱动频率下的迟滞特性，采用Bouc-Wen模型对驱动器迟滞现象进行了建模，并采用粒子群算法（PSO）辨识模型参数，与实际测量迟滞曲线进行了对比，在10~60 Hz范围内所建立的迟滞模型能够较为精确地描述压电驱动器迟滞现象。建立了基于Bouc-Wen逆模型的前馈补偿控制与PID反馈控制相结合的复合控制策略，实验结果显示该控制策略能够在10~60 Hz较宽的频率范围内有效抑制该压电驱动器迟滞现象。建立了考虑驱动器迟滞的主动控制后缘襟翼振动控制动力学模型，并对中等速度稳态前飞条件下后缘襟翼振动控制性能进行了仿真，仿真结果显示驱动器迟滞会在一定程度上削弱振动控制性能，而采用复合控制可以提高后缘襟翼旋翼振动控制性能。     

The adjusted optical properties for Galileo/BeiDou-2/QZS-1 satellites and initial results on BeiDou-3e and QZS-2 satellites

Solar Radiation Pressure (SRP) is the dominant non-gravitational perturbation for GNSS (Global Navigation Satellite System) satellites. In the absence of precise surface models, the Empirical CODE Orbit Models (ECOM, ECOM2) are widely used in GNSS satellite orbit determination. Based on previous studies, the use of an a priori box-wing model enhances the ECOM model, especially if the spacecraft is a stretched body satellite. However, so far not all the GNSS system providers have published their metadata. To ensure a precise use of the a priori box-wing model, we estimate the optical parameters of all the Galileo, BeiDou-2, and QZS-1 (Quasi Zenith Satellite System) satellites based on the physical processes from SRP to acceleration. Validation using orbit prediction proves that the adjusted parameters of Galileo and QZS-1 satellites exhibit almost the same performance as the corresponding published and “best guess” values. Whereas, the estimated parameters of BeiDou-2 satellites demonstrate an improvement of more than 60% over the initial “guess” values. The resulting optical parameters of all the satellites are introduced into an a priori box-wing model, which is jointly used with ECOM and ECOM2 model in the orbit determination. Results show that the pure ECOM2 model exhibits better performance than the pure ECOM model for Galileo, BeiDou-2 GEO and QZS-1 orbits. Combined with the a priori box-wing model the ECOM model (ECOM+BW) results in the best Galileo, BeiDou-2 GEO and QZS-1 orbits. The standard deviation (STD) of satellite laser ranging residuals reduce by about 20% and 5% with respect to the pure ECOM2 model for Galileo and BeiDou-2 GEO orbits, while the reductions are about 40% and 60% for QZS-1 orbits in yaw-steering and orbit-normal mode respectively. BeiDou-2 IGSO and MEO satellite orbits do not benefit much from the a priori box-wing model. In summary, we suggest setting up a unified SRP model of ECOM+BW for Galileo, QZS-1, and BeiDou-2 orbits based on the adjusted metadata. In addition, we estimate the optical parameters of BeiDou-3e and QZS-2 satellites using a limited number of tracking stations. Results regarding the unified SRP model indicate the same advantages, the STD of satellite laser ranging residuals reduces by about 30% and 20% for QZS-2 and BeiDou-3e orbits respectively over orbit products without a priori model. The estimation procedure is effective and easy to apply to the new emerging satellites in the future.     

多支点柔性转子系统临界转速稳健设计方法

基于响应面法和容差模型提出了定量考虑参数变差影响的转子系统临界转速稳健设计方法。该方法利用响应面模型获得多参数、多目标之间的函数关系,并以多阶临界转速分布为约束条件、以临界转速对支承刚度变差敏感度最低为设计目标。对小涵道比涡扇发动机低压转子系统临界转速稳健设计结果表明:在考虑各支点支承刚度变差情况下,采用多参数、多目标稳健设计方法,可保证多支点柔性转子系统的临界转速特性在满足设计要求的同时,转子系统临界转速对支承刚度变差的敏感度最低,验证了该方法的有效性。      

Investigation on nonlinear lateral-torsional coupled vibration of a rotor system with substantial unbalance

Substantial unbalance may be caused by fan blade off during the operation period of gas turbine engines, and related dynamic problems are very critical to the safety design of rotor system in aero-engine. This article aims to understand lateral-torsional coupled vibration of the rotor system with substantial unbalance. The governing equation of a modified unbalanced rotor system is established based on Lagrangian approach. Then, a mathematical analytical method is proposed in which a linear approximation is derived and the Floquet theory and Hill’s method are incorporated, from which the modal characteristics of the unbalanced rotor are obtained. The modal characteristics of the unbalanced rotor system are revealed comprehensively for the first time. Furthermore, the relation between the modes and responses of the unbalanced rotor is discussed in detail. The results show that the lateral vibration and torsional vibration of the unbalanced rotor are coupled through the inertial terms in the governing equations. Due to the coupling, veering and lock-in phenomena occur between the frequencies of the forward whirl mode and the torsional mode. Furthermore, lock-in can lead to a kind of principal instability. With regard to the response of the unbalanced rotor, both natural vibration components and enforced vibration components appear in the lateral response, while only natural vibration components appear during torsional vibration. Moreover, natural vibration components play a crucial role in the response within the principal instability region and cause divergence of the vibration amplitudes in the lateral and torsional directions.     

吸气式电推进系统可行条件分析

吸气式电推进系统作为有可能实现长寿命超低轨飞行的技术而被关注。根据不同轨道环境条件，采用管状结构进气道、以及机械增压的吸气方式，讨论了吸气式电推进系统所需的可行条件。分析表明，在轨高度180~240km，航天器所需总功耗与迎风面之比需要大于2kW/m2，电推力器比冲需大于4×104m/s，方可满足推阻平衡需求。分析得出，实现吸气式系统在地球轨道的运用，关键技术在于增加气体收集效率并且降低收集功耗，同时电推力器的效率还需进一步提升。