喷管内型面烧蚀对发动机能量的影响

根据同一推进剂不同结构的两种型号发动机的试验结果，分析了喷管内型面烧蚀对发动机能量影响，提出了在两种烧蚀率相差较大的材料之间镶嵌一种烧蚀率适中的材料，可减少喷管内型面的烧蚀，提高喷管推力效率。     

位移序列多进制扩频通信方式

提出用 m序列的位移序列做扩频序列的多进制扩频通信方式 ,并给出了它的系统模型 ,分析了它的通信性能。理论分析证明 ,用 m序列的位移序列构成的多进制扩频通信方式具有很高的通信有效性和通信可靠性     

破片式反导导弹引战配合仿真与效率计算

为研究破片式反导导弹的引信、战斗部、弹目交会参数和背景干扰等对引战配合效率的影响,构建了超低空反导导弹引战配合仿真与效率计算工作平台,给出仿真及效率计算模型。在不同导弹、目标和背景干扰等参数条件下,模拟导弹的引战配合过程并计算其效率,获得了引信启动点散布、延迟时间、战斗部破片初速、飞散角、脱靶量以及背景干扰等系统参数对导弹引战配合效率的影响规律。     

用推力矢量控制技术改进超声速飞行器空气动力特性

为了提高某超声速飞机的空气动力学效率和机动性能，本文采用低阶的三维板块法和DATCOM半经验公式，在亚声速和超声速条件下，对不同马赫数和迎角情况计算了基本气动外形的飞机空气动力学特性、表面压力分布以及最大升力。此外还开发了一套软件以实现由引进的先进气动操纵面（如鸭翼等）控制的二维推力矢量技术。试验结果表明：气动操纵面结合推力矢量技术能够产生足够的低头力矩，且有能力满足高度机动飞行时的稳定性要求。此外，不论是亚声速还是超声速飞行，气动操纵面均可以提高气动效率5％-6％。     

面向绿色制造的高效冷却技术及其试验

绿色制造和高效加工是21世纪先进制造业的必然趋势,为实现绿色高效加工,本文提出了一种新型的绿色高效冷却技术——低温气动喷雾射流冲击冷却技术,通过低温气流运载少量冷却液以喷雾射流冲击的形式到达加工区实现强化换热,将加工区的换热水平提高到一个全新的水平.瞬态实验结果表明,在射流速度40 m/s、靶距10 mm的射流条件下,这种冷却方式可提供的临界热流密度高达60W/mm^2,相对于磨削发生烧伤的临界热流密度提高了6倍以上.     

扰流环对粉末发动机燃烧流动影响的数值模拟

为了提高粉末火箭发动机的燃烧效率,通过数值模拟方法研究了扰流环的有无、通径及位置对燃烧室燃烧流动特性的影响。结果表明:扰流环会增强Al颗粒和气相的掺混和换热程度,促进Al颗粒蒸发和燃烧,从而提高粉末火箭发动机的燃烧效率。当扰流环通径比在0.538~0.846范围内时,扰流环的通径越小,燃烧效率越高;当扰流环头部距离比在0.3~0.8范围内时,扰流环位置离头部越近,燃烧效率越高。设计扰流环时,应在距离燃烧室头部30%~40%的位置布置小通径的扰流环。      

Effect of protrusion amount on gas ingestion of radial rim seal

In this paper, the effect of different amount of protrusion on various parameters in rotor–stator system was experimentally studied by measuring CO₂ concentration and pressure, in order to obtain the optimal protrusion amount. The parameters of different dimensionless sealing flow were measured under the condition that the annulus Reynolds number was 4.39 × 10⁵ and the rotating Reynolds number was 1.05 × 10⁶. The results show that the change of the amount of protrusions has little effect on the static pressure in the cavity, and the static pressure change near the sealing ring is almost negligible. But the total pressure and sealing efficiency increase first and then decrease with the increase of the amount of protrusion. The variation of power consumption is the same. A complex vortex structure will appear at the high radius region when the protrusion is installed. On the other hand, the protrusion can effectively reduce the minimum sealing flow of the rotor–stator cavity. Furthermore, considering the sealing efficiency and power consumption, the best range of the protrusion amount is about 36. The ratio near this range can optimally balance the alleviation of the gas ingestion and the reduction of the power consumption.     

等离子体助燃下超燃支板燃烧室燃烧特性数值研究

为了将支板喷注器与等离子体射流这两种促进超声速燃烧室燃烧的方式结合起来,设计了一种带有等离子体射流喷孔的支板燃烧室,并在超声速来流的条件下,针对燃料喷注总压、燃料喷注位置、等离子体射流介质、等离子体射流总压对燃烧室燃烧性能的影响进行了三维数值模拟。研究发现:增大燃料的喷注总压,燃烧室的燃烧范围明显增大,燃烧效率呈现出先增大后减小的趋势,在燃料喷注总压为2.0MPa时,燃烧效率达到最大值90.4%;不同的燃料喷注位置对燃烧室的燃烧范围影响较小;等离子体射流介质为O2时,燃烧效率最高,燃烧范围最广;提高等离子体射流的喷注总压,能够提升凹腔剪切层高度,有效促进燃烧,但同时也带来了更高的总压损失。     

Aerodynamic performance enhancement for flapping airfoils by co-flow jet

Introducing active flow control into the design of flapping wing is an effective way to enhance its aerodynamic performance. In this paper, a novel active flow control technology called Co-Flow Jet (CFJ) is applied to flapping airfoils. The effect of CFJ on aerodynamic performance of flapping airfoils at low Reynolds number is numerically investigated using Unsteady Reynolds Averaged Navier-Stokes (URANS) simulation with Spalart-Allmaras (SA) turbulence model. Numerical methods are validated by a NACA6415-based CFJ airfoil case and a S809 pitching airfoil case. Then NACA6415 baseline airfoil and NACA6415-based CFJ airfoil with jet-off and jet-on are simulated in flapping motion, with Reynolds number 70,000 and reduced frequency 0.2. As a result, CFJ airfoils with jet-on generally have better lift and thrust characteristics than baseline airfoils and jet-off airfoil when C_μ is greater than 0.04, which results from the CFJ effect of reducing flow separation by injecting high-energy fluid into boundary layer. Besides, typical kinematic and geometric parameters, including the reduced frequency and the positions of the suction and injection slot, are systematically studied to figure out their influence on aerodynamic performance of the CFJ airfoil. And a variable C_μ jet control strategy is proposed to further improve effective propulsive efficiency. Compared with using constant C_μ, an increase of effective propulsive efficiency by 22.6% has been achieved by using prescribed variable C_μ for NACA6415-based CFJ airfoil at frequency 0.2. This study may provide some guidance to performance enhancement for Flapping wing Micro Air Vehicles (FMAV).     

多面体网格在静气动弹性计算中的应用

介绍了多面体网格技术在静气动弹性问题中的应用.基于M6算例和径向基函数插值法,探究了多面体网格的CFD计算效率和变形能力,使用AGARD445.6机翼进行了静气动弹性数值计算.结果表明,多面体网格具有计算效率高、变形能力强、计算结果准确等优点,可适用于静气动弹性问题的数值计算.