减压腔宽度对刷式密封泄漏特性和滞后效应的影响

对减压腔轴向宽度分别为0、04 mm和06 mm的基本型和两种低滞后刷式密封结构进行了静态和动态下压差升降和转子转速升降循环试验,并对其泄漏特性和滞后效应进行了研究。研究结果表明:压差大于02 MPa后,同一压差下的动态泄漏系数比静态降低约14%~20%;低滞后结构的密封性能优于基本型,其泄漏系数最高比基本型降低约20%;静态压差升降循环中,减压腔轴向宽度为06 mm的低滞后结构的滞后效应最强;动态的压差升降循环中,基本型结构的滞后效应最强。转子转速升降循环前后,w为06 mm结构泄漏系数减小约15%,滞后效应最强,减压腔轴向宽度为04 mm结构几乎不存在滞后效应;三种结构中,减压腔轴向宽度为04 mm的结构密封性能最优,滞后效应也最弱。     

Median filtering algorithms for multichannel detectors

Particle detectors of worldwide networks are continuously measuring various secondary particle fluxes incident on Earth surface. At the Aragats Space Environmental Center (ASEC), the data of 12 cosmic ray particle detectors with a total of ∼280 measuring channels (count rates of electrons, muons and neutrons channels) are sent each minute via wireless bridges to a MySQL database. These time series are used for the different tasks of off-line physical analysis and for online forewarning services. Usually long time series contain several types of errors (gaps due to failures of high or low voltage power supply, spurious spikes due to radio interferences, abrupt changes of mean values of several channels or/and slowly trends in mean values due to aging of electronics components, etc.). To avoid erroneous physical inference and false alarms of alerting systems we introduce offline and online filters to “purify” multiple time-series. In the presented paper we classify possible mistakes in time series and introduce median filtering algorithms for online and off-line “purification” of multiple time-series.     

基于金属密封垫圈非线性变形仿真的预紧设计

为确保密封结构能有效阻止箱体内部介质的泄漏,要求密封面具备一定的密封比压,即通过施加合理的拧紧力矩来控制密封件的压缩量。目前主要采用试验方法验证一系列拧紧力矩下的密封效果,从而获取临界力矩值并确定可靠的拧紧力矩设计值。文章基于试验经验做出了合理的假设以建立简化的非线性有限元分析模型,对金属垫圈在压紧力下的塑性变形进行仿真,通过金属垫圈发生临界变形量的压紧力反推出拧紧力矩的临界值。该方法获取的临界力矩值与试验方法相近,可以有效地提高设计效率,降低试验成本。     

封严篦齿腔内流动及旋涡分布和顶板换热特性的实验研究

自行设计了吸气式篦齿换热风洞并对篦齿腔内部旋涡分布及流场和篦齿顶板换热特性进行了详细的研究。测出了在不同雷诺数和齿隙比篦齿腔中旋涡分布和顶板换热规律。从机理上分析了雷诺数和齿隙比对篦齿腔内流动旋涡分布及顶板表面局部换热规律的影响。     

某型飞机机翼整体油箱工艺研究

介绍了某型机机翼整体油箱的研制过程,针对总体气动、结构和使用维护等对整体油箱提出的性能要求,工程部门相应采用严格的环境措施、确保协调精度的预装配措施以及湿连接、密封装配措施等,解决了研制过程中诸多关键难题,保证了整体油箱的研制进度和产品质量,经各种试验检测和试飞考核,该整体油箱质量稳定可靠,性能良好。     

任意铺设复合材料矩形薄板横向弯曲一般解析解

采用复级数方法首次建立了任意铺设复合材料矩形板横向弯曲一般解析解．引入（U，V，W）＝∑（A，B，C）exp（imπξ）exp（imπηr），并代人层合板平衡方程组，推出实数型级数解，将其回代入平衡方程组中任两个，可确定待定系数（A，B，C）之间关系；引入将3个平衡方程归并为一个8阶偏微分方程的方法给出问题特解．将一般解析解代入边界条件，用余弦级数的方法确定待求系数．给出算例以验证解的有效性．     

液体火箭发动机涡轮泵用机械密封温度场及热载变形研究

基于ANSYS数值计算软件,建立了液体火箭发动机涡轮泵用机械密封的二维稳态传热模型,依靠经验公式确定了模型的对流换热系数。计算了密封环的温度场和热载变形,分析了密封端面比压、回流流量以及不同材质对密封温度场的影响规律。结果表明:密封端面最高温度发生在靠近密封环内径处,且密封端面比压越大密封环温度梯度越大;密封环热载变形呈收敛间隙,最大变形发生在动环端面的外径处,其值约为2.2μm;密封环端面最高温度随回流流量增加而减小,当回流流量从0.1~0.6 kg/s变化时,密封环端面最高温度可降低18%(从100℃降至82℃);当回流流量增大到0.3 kg/s时,继续提高对密封环端面温升的控制不再显著;采用高导热系数的摩擦副材料能够显著降低端面温升和温度梯度,提高密封工作可靠性。     

Leakage performance of floating ring seal in cold/hot state for aero-engine

Rotating experimental investigations were carried out to study the oil sealing capability of two different floating ring seals in cold/hot state for aero-engine. High-speed Floating Ring Seal(HFRS) is a seal with the inner diameter of 83.72 mm and maximum speed of 38000 r/min, and Low-speed Floating Ring Seal(LFRS) is another seal with the inner diameter of 40.01 mm and maximum speed of 18000 r/min. In hot state, sealing air with the temperature of 371 K and oil with the temperature of 343 K was employed to model the working conditions of an aero-engine. Comparisons between floating ring seal and labyrinth seal were done to inspect the leakage performance.More attention was paid to the critical pressure ratio where the oil leakage began. Results show that the critical pressure ratio in cold state is obviously larger than that in hot state for both seals. An underlying sealing mechanism for floating ring seal is clarified by the fluid film, which closely associates with the dimensionless parameter of clearance over rotating diameter(2 c/Dr). Another fantastic phenomenon is that the leakage coefficient in hot state, not the leakage magnitude, is unexpectedly larger than that in cold state. Overall, the leakage performance of the floating ring seal is better than the labyrinth seal.     

金属密封件镀金工艺研究

介绍了金属密封件镀金工艺技术,该工艺采用亚硫酸盐镀金方案,以单脉冲电源为镀覆电源,以预镀镍层为中间镀层来制备金镀层,得到了结晶细致、厚度均匀并与基体上结合牢固的金镀层.研究了金镀层的沉积速率和结合强度,观察了镀层的表面形貌和组织结构,进行了金属密封件气密性试验和典型试验.结果表明：金属密封件金镀层的技术性能指标满足设计要求,能够应用于液体火箭发动机中,该发动机已通过地面热试车考核.     

Dynamic analysis of C/C composite finger seal

A seal device as an important component of aeroengines has decisive influence on per- formance, reliability, and working life of aeroengines. With the development of aeroengines, demands on the performance characteristics of seal devices are made strictly. Finger seal as a novel kind of sealing device, recently attracts more and more attentions in academic circles and engineer- ing fields at home and abroad. Research on finger seals has been extensively developed, especially on leakage and wear performances under dynamic conditions. However, it is a pity that the work on finger seals has been limited with a single approach that is improving the performance by structural optimization; in addition, the technology of dynamic analysis on finger seals is weak. Aiming at the problems mentioned above, a distributed mass equivalent dynamic model of finger seals considering the coupling effect of overlaid laminates is established in the present paper, the dynamic perfor- mance of 2.5 dimension C/C composite finger seal is analyzed with the model, and then the effects of fiber bundle density and fiber bundle preparation direction on finger seal＇s dynamic performance are discussed, as well as compared with those of Co-based alloy finger seal. The current work is about dynamic analysis of finger seals and application of C/C composite in this paper may have much academic significance and many engineering values for improving research level of finger seal dynamics and exploring feasibility of C/C composite being used for finger seals.