Trajectory optimisation in electrical discharge machining of three-dimensional curved and twisted channels

Numerical control electrical discharge machining(NC EDM) is one of the most widely used machining technologies for manufacturing a closed blisk flow path, particularly for three-dimensional(3D) curved and twisted flow channels. In this process, tool electrode design and machining trajectory planning are the key factors affecting machining accessibility and efficiency. Herein, to reduce the difficulty in designing the electrode and its motion path in the closed curved and twisted channels, a heur...     

Breakthrough detection in electrochemical discharge drilling to enhance machining stability

Film cooling holes are widely used in aero-engine turbine blades. These blades feature large numbers of holes with complex angles and require a high level of surface integrity. Electrochemical discharge drilling(ECDD) combines the high efficiency of electrical discharge drilling(EDD) with high quality of electrochemical drilling(ECD). However, due to the existence of a variety of energy for material removal, accurate and timely detection of breakthroughs is fraught with difficulties. An insuffic...     

城市环境下北斗B-CNAV1电文RS-LDPC 级联编码方法

针对城市环境下卫星导航系统用户接收终端对电文编译码算法的低复杂度和抗衰落性能需求，以北斗导航系统B-CNAV1电文为改进对象提出了一种外码采用RS码、内码采用二进制LDPC码的电文级联编码方法。通过RS码提高电文对抗突发错误的能力，同时利用二进制LDPC码保证电文对抗随机错误的能力。采用LMS信道对城市接收环境建模，仿真结果验证了本文提出的RS-LDPC级联码与B-CNAV1电文64进制LDPC码具有相近的性能，同时大幅降低了算法复杂度，较好地实现了电文纠错性能和实现复杂度的平衡，提供了一种适用于城市环境的高性能、低复杂度电文编码方法。     

Real-time ray-based channel generation and emulation for UAV communications

A real-time ray-based hardware emulator for Unmanned Aerial Vehicle (UAV) communication channels which suits for the Three-Dimensional (3D) dynamic scenarios and considers the movements of both terminals is developed in this paper. The time-variant channel parameters, i.e., ray delay, ray gain, and ray Doppler frequency are precalculated in the host by using the Ray Tracing (RT) method. Meanwhile, RT simulation dramatically increases the number of valid rays. To address the problem of resource limitation and huge computational burden in the implementation, an efficient ray coefficients generation method based on iteration is proposed and implemented. With the advantages of low cost and high flexibility, a Software Defined Radio (SDR) hardware platform is used to emulate the ray-based UAV channels by utilizing the compact architecture including the Time-Division (TD) scheme and Tapped-Delay Line (TDL) for channel convolution. Finally, hardware measurement results demonstrate that the properties of emulated channel, i.e., Power Delay Profile (PDP) and Doppler Power Spectrum Density (DPSD) consist with the simulated ones, which verifies the correctness of hardware implementation. The proposed channel emulator provides an efficient way for optimization, verification, and evaluation of UAV communication systems.     

无人机协同测控中SC-FDMA技术设计

针对无人机协同任务测控传输的多机接入问题,提出基于分布式任务分配模型的高动态SC-FDMA技术.通过将贪婪原则、信道动态分配机制和多用户接入技术结合,利用集中映射方式设计子信道数目可调的映射规则,配置各无人机节点所占用子载波数目.仿真结果表明,与传统FDMA、CDMA、TDMA、OFDMA等相比,基于SC-FDMA设计...     

航空用不锈钢磨粒流光整加工表面完整性研究

为研究磨粒流光整加工不锈钢闭式整体叶环的表面完整性，通过对电火花制备的不锈钢试样进行加工时间、加工压强及磨料目数的单因素试验，研究3个因素对加工后表面完整性的影响。结果表明：表面粗糙度Ra随着加工时间的增加而降低，从初始时的1.459μm降至60 min时的0.193μm，降低速率越来越慢，最后趋于稳定。磨粒流加工有效去除了加工表面再铸层。显微硬度在加工后明显降低，由450～950 HV降至270～350 HV且分布均匀性得到改善。显微硬度随着加工时间的增加整体上呈降低趋势，并出现了一定的加工硬化现象。在使用不同目数的磨料进行磨粒流加工后，残余应力由拉应力变为压应力。随着加工时间和加工压强的增加，试样表面越平整，抛光效果越好。     

Time resolved study of laser triggered electric discharge spark in atmosphere: Machine learning approach

In this paper we analyze the possibilities of using machine learning algorithms for analysis of optical spectra of electric discharge spark in atmosphere. Breakdown in air can be initiated by intense laser pulse, making plasma which has a significant electrical conductivity. The formed plasma can be further maintained by electric current obtained from capacitor discharge. In such a case the capacitor voltage can be much lower than the striking voltage (the voltage needed to initiate the electric breakdown in air). Present setup has timing precision and low jitter of fast laser and arbitrary high energies corresponding to capacitance and voltage to which the capacitor is charged. We have used a streak camera equipped with a spectrograph to analyze optical emission of plasma obtained in this way. Q-switched Nd:Yag laser was used to achieve the initial breakdown in air. Machine learning methods were used in order to classify optical spectra of plasmas with different electron temperatures obtained with different excitation energies. We have shown that, instead of using the usual way of identifying the spectral peaks and calculating their intensity ratio, it is possible to train the computer software to recognize the spectra corresponding to different electron temperatures. Principal component analysis was used to reduce the dimensionality of problem. We present possibilities of plasma electron temperature estimation based on several clustering algorithms.     

Recent developments in thermal characteristics of surface dielectric barrier discharge plasma actuators driven by sinusoidal high-voltage power

Flow control using surface Dielectric Barrier Discharge(DBD) plasma actuators driven by a sinusoidal alternating-current power supply has gained significant attention from the aeronautic industry. The induced flow field of the plasma actuator, with the starting vortex in the wall jet,plays an important role in flow control. However, the energy consumed for producing the induced flow field is only a small fraction of the total energy utilized by the plasma actuator, and most of the total energy i...