悬臂空心梁式加速度计的设计

分析证明:悬臂梁式加速度计的灵敏度与它的谐振频率的平方成反比。因此,欲展宽频带而保持灵敏度不变就很困难。利用应力集中的方法可以有效地解决这一问题。采用空心梁结构不仅能产生应力集中而且能减少梁的自身质量带来的影响,可以有效地展宽频带。文中给出了几种梁的刚度计算。     

磁选态单束铯束管束光学参数的模拟计算和设计

为提高铯束管跃迁信号强度,在束光学参数设计中,用蒙特卡罗方法模拟计算铯原子通过率和未跃迁比例。通过改变模拟计算中的束光学参数,分析铯原子通过率、未跃迁比例和倍增器首极电流的变化趋势,得到了主要束光学参数的合理取值范围。在铯束管实际装配和试验中使用束光学参数设计结果,有效地增加了倍增器首极电流。     

永磁约束电子束轨迹实验研究

通过设计并运用一种直流电子束轨迹简易测量方法,开展了永磁约束电子束轨迹实验研究,得到了永磁铁环对60~80 ke V电子束约束作用的实验数据。结果表明:该测量方法方便有效,结果较为准确;永磁铁对电子束聚焦作用明显,并呈现出一定的规律性。对永磁铁约束电子束研究工作奠定了基础。     

激光器性能综合测试设备研制

介绍了激光器的主要性能指标,根据实际需要进行了激光性能测试设备的研究,提出了一种周全的激光性能测试设备研制方案,对该设备的结构设计、光路设计、以及测试方法作了详尽论述。设备中利用两对相互垂直的P分光镜和S分光镜以补偿偏振光在45°面上透反射率不同而造成的测量误差,进一步保证了激光能量测试的准确性。误差分析结果表明该设备满足实际应用中对激光器性能的测试要求。     

10cm氙离子推力器变推力特性研究

非重力阻尼的连续、快速、高精度补偿是实现重力梯度测量卫星精细重力场测量的关键技术之一,直接影响到整星工程任务的成败。针对重力梯度测量卫星在轨飞行期间对电推进系统宽范围连续变推力能力的应用需求,分析了10cm氙离子推力器推力调节响应特性。在此基础上,通过对阳极电流、励磁电流和阳极流率等推力高敏感响应参量的组合调节,开展了推力调节试验研究,验证了10cm氙离子推力器宽范围连续变推力调节能力,获得了1～20mN范围内的推力调节性能及其变化规律。试验结果表明：在采用地面供电、供气设备条件下,10cm氙离子推力器能够在100～597W的功率范围内实现0.98～20.29mN的推力宽范围调节,比冲175～3500s,推力分辨率优于50μN。研究为建立10cm氙离子电推进系统的推力控制数学模型及调节控制算法奠定基础。     

Spectroscopic Constraints on Models of Ion-cyclotron Resonance Heating in the Polar Solar Corona

Using empirical velocity distributions derived from UVCS and SUMER ultraviolet spectroscopy, we construct theoretical models of anisotropic ion temperatures in the polar solar corona. The primary energy deposition mechanism we investigate is the dissipation of high frequency (10-10000 Hz) ion-cyclotron resonant Alfvén waves which can heat and accelerate ions differently depending on their charge and mass. We find that it is possible to explain the observed high perpendicular temperatures and strong anisotropies with relatively small amplitudes for the resonant waves. There is suggestive evidence for steepening of the Alfvén wave spectrum between the coronal base and the largest heights observed spectroscopically. Because the ion-cyclotron wave dissipation is rapid, even for minor ions like O⁵⁺, the observed extended heating seems to demand a constantly replenished population of waves over several solar radii. This indicates that the waves are generated gradually throughout the wind rather than propagated up from the base of the corona. This revised version was published online in June 2006 with corrections to the Cover Date.     

飞机下滑波束导引系统设计及仿真

下滑波束导引系统是飞机在自动着陆时所采用的一种重要无线电波束导引系统。首先,简要阐述了下滑波束导引系统的基本工作原理;然后,对导引系统的运动学环节及下滑耦合器进行分析,对飞机下滑波束导引系统结构进行设计;最后,在MATLAB平台下,对所设计的下滑波束导引系统进行大量仿真研究。仿真结果显示。所设计的下滑波束导引系统结构是合理的,其控制系统是稳定的,且其稳态性能也得到改善。     

公差原则中相关要求的计算问题

关于公差原则中的相关要求的计算问题 ,本文提出了两种方法 :计算法和图解法。运用这两种方法可以简化此类问题的计算过程 ,准确求得计算结果。     

RAYTHEON 10SS雷达气象波束开关告警的产生及排除

自昆明西山雷达站RAYTHEON／＆司的10SS一次雷达投产以来，出现过3次气象波束开关告警，告警的现象均为A／B两个通道频繁交替告警，经过检查一次是由于天线平台的信号电缆头问题所致，另外两次是因为旋转铰链的电刷问题所致，本文将当时排除故障的情况和想法写出来，和大家一起来讨论今后如何更好地排除该故障。     

Antenna pattern control of planar arrays for long distance communications

As an alternative to standard antennas and due to the advent of low-cost digital processors and materials, adaptive antenna arrays are increasingly considered for applications in long distance communications. The pattern beam control potentialities provide the performance improvement of the communication systems. In this context, this work presents a technique that permits to synthesize the antenna pattern of a planar array. Considering that the relationship between the array factor and the array excitations for the far field region is a Fourier transform in the appropriate variables, the non-uniform sampling procedure is extended for planar arrays. These arrays permit a further control of the antenna pattern since two dimensions of space are used. The technique considers a number of array factor points equal to the array size, which is used to impose appropriated values in the antenna pattern. The produced array factor passes through those points with the desired values, which allows the synthesis of antenna patterns with appropriated characteristics. The theory is presented in order to develop the necessary direct expressions to calculate the array excitation. The array factor can be obtained using the inverse Fourier transform. As application examples, with this technique it is possible to define the level of each sidelobe of the antenna pattern, to control the main beam and to impose nulls in prescribed directions of the pattern.