固体火箭发动机试验模态分析技术研究

将固体火箭发动机划分为144个自由度，采用锤击法，单点激励多点响应（SIMO）对其在4种工况下进行了频率响应的测量，应用了多种方法进行模态参数识别和数据拟合，并对其结果进行比较，获得了发动机在各工况1kHz以内的各阶固有频率、振型和阻尼，并对试验模态分析技术在固体火箭发动机试验中的应用进行了研究。     

随振动量级增加卫星结构频率下移的分析

对卫星振动频率随量级增加而出现下降，即振动频率“漂移”的现象进行了初步分析。发现随振动量级的增加。结构的非线性表现突出。结构的刚度下降和阻尼增加，可认为主要是由蜂窝材料的非线性因素所致。     

异型封闭腔辐射几何学问题

讨论了解决异型封闭腔辐射几何学问题的几种方法:异型封闭腔内,表面间可见性的判断方法;优化异型封闭腔角系数计算的方法;确定异型封闭腔内定向辐射的壁面辐射源的方法.计算了两种结构喷管封闭腔内的角系数,并从角系数的互换性和完整性定理验证了方法的正确性和有效性,为异型封闭腔的辐射计算解决了几何问题.     

The fundamental parameters of the central stars of eight WR ring nebulae

We describe work that has recently been completed on deriving the fundamental parameters of eight WR stars through the photoionization modelling of their surrounding nebulae using non-LTE WR flux distributions. The resulting effective temperatures range from 57 000–71 000 K for the WN4-5 stars and <30 000–42 000 K for the WN6-8 stars. The derived stellar parameters are compared with those obtained from stellar emission line modelling. We find good agreement for the hot early WN stars, indicating that the non-LTE WR flux distributions have essentially the correct shape in the crucial far-UV region. We find lower temperatures for the four cooler late WN stars, particularly for the two WN6 stars. For the nebulae surrounding these stars, we find that the model flux distributions produce too much nebular ionization. We suggest that these discrepancies arise because of the lack of line-blanketing in the WR atmospheres. For the WO1 central star of G2.4+1.4, with strong nebular He II 4686 A emission, we derive a temperature of 105 000 K, somewhat less than previous estimates. The positions of our eight WR stars on the H-R diagram are compared with the evolutionary tracks of Maeder (1990) for solar metallicity. In common with previous workers, we find that our derived luminosities are too low, giving an initial mass range of 25–40 M, below that expected for the majority of WR stars.     

Energetic particles at high latitudes

We review work on diffusion coefficients of energetic particles with an attempt to extract implications on their behaviour at high latitudes. In the ecliptic plane results from solar energetic particle propagation between the Sun and about 5 AU can be described by an effective radial mean free path _r which is approximately constant as a function of distancer. When particle propagation in three dimensions in the heliosphere is considered it is not sufficient to consider _r only. Jovian electrons can be used as probes to determine the parameters of three-dimensional diffusion. In the polar regions diffusion is dominated by its parallel component. Some predictions how should vary with latitude are discussed. For different choices of this variation we present expectations for intensity-time profiles of solar particle events during the Ulysses polar passages.     

航空发动机全程滑态变结构控制研究

一种新的滑模变结构控制方法-全程滑态变结构控制首次应用于航空发动机控制系统，该控制方法能有效地缩短系统状态到达滑动模态的时间，避免了定常滑态变结构控制系统在能达阶段对扰动的敏感性，且其控制律的设计可以改善系统的瞬态性能，克服未知参数摄动的影响，仿真结果表明，基于全程滑态变结构控制所设计的发动机控制系统，其鲁棒性要优于发动机定常滑态结构控制系统。     

流线追踪Busemann进气道设计参数的选择

为了研究型面设计马赫数、唇口偏移量对流线追踪Busemann进气道设计点性能的影响规律,寻求最佳性能的进气道,对设计马赫数为6,具有不同型面设计马赫数和唇口偏移量的流线追踪进气道进行了数值模拟。研究表明:选取低于马赫数6的型面设计马赫数,可获得较高的流量系数和增压比,而其压缩效率并不低;进气道唇口偏移量增大,会导致流量系数、增压比变小,但却有利于减小进气道内的分离程度,还会影响隔离段内的流动,因此唇口偏移量的选取需要综合考虑。     

特征结构配置在飞机模态解耦中的应用

主要对特征结构配置在飞机模态解耦中的应用问题进行研究,并以某飞机横航向小扰动运动为例,按照飞机飞行品质规范要求,给出荷兰滚模态和滚转模态解耦控制的设计方法。     

飞行器动态稳定性参数的数值计算方法

本文提出了一种确定飞行器动态稳定性参数的数值方法。本文首先研究了气动力与飞行器运动状态参数之间的关系，在此基础上给出了稳定性参数的定义。根据这一定义并结合计算流力学和参数辨识方法，构造了计算飞行器稳定性参数的完整数值方法，数值实验表明，该方法具有通用性强和准确度较高的优点。     

基于迭代学习控制的导弹PID控制器参数寻优

针对设计导弹PID控制器时存在的对比例、微分、积分3个控制参数大量盲目试凑的问题,利用迭代学习算法对控制参数进行自动寻优,最终得到最佳控制参数,从而实现了对PID控制器参数自动寻优的目的,简化了控制器的设计过程。通过仿真结果验证该方法在PID控制器参数自动寻优上是有效的,同时也为导弹控制器参数整定提供了工程适用的方法。