Effect of bristle pack position on the rotordynamic characteristics of brush-labyrinth seals at various operating conditions

Over the last few decades, the research on the effect of bristle pack position on the rotordynamic characteristics of the brush-labyrinth seals is not sufficient. To this end, two kinds of brush-labyrinth seals for the bristle pack element installed upstream of the labyrinth teeth named BSU and installed downstream of the labyrinth teeth called BSD were used to investigate the effect of bristle pack position on the rotordynamic characteristics of the brush-labyrinth seals. Using the numerical model combining the porous medium model and the whirling rotor method, the rotordynamic characteristics of the BSU and BSD at various operating conditions including four kinds of pressure ratios, five kinds of inlet preswirl speeds and four kinds of rotor spinning speeds were conducted. The obtained results show that the effects of operating conditions on rotordynamic coefficients for the different seal configurations are different. The direct stiffness, cross-coupled stiffness and direct damping of the BSU are lower than those of the BSD. The rotordynamic coefficients of the BSU are more insensitive to the operating conditions variation. From the perspective of the seal stability, the BSU is a better brush-labyrinth seal configuration at high pressure ratio, high positive preswirl or high rotor spinning speed conditions. While in the case of low pressure ratio, low positive preswirl or low rotor spinning speed conditions, the BSD is a better choice.     

Influence of thickness and initial groove angle in M–K model on limit strain of 7B04 by considering through-thickness stress

Marciniack–Kuczinski (M–K) model is widely used to predict material’s forming limit curve (FLC). The prediction of FLC traditionally neglected through-thickness normal stress. However, it cannot be neglected in some forming processes. Much work has been done to study the effect of through-thickness normal stress on FLC with constant through-thickness normal stress or constant ratio of through-thickness normal stress and maximum principal stress. In addition, based on Nakazima test process, the ratio of through-thickness normal stress and maximum principal stress has been derived, which was a function of instantaneous thickness and loading path. Here, initial groove angle in M–K model was not considered. In this paper, uniaxial tension tests and Nakazima tests were performed on 7B04 aluminum alloy. Based on Hill 48 yield criterion and M–K model, the prediction model of FLC was established. The increase of thickness can enhance FLC. Meanwhile, it is necessary to consider through-thickness normal stress and initial groove angle in prediction model. On the left side of FLC, the effect of initial groove angle on FLC is weakened by increasing sheet thickness. On the right side of FLC, the effect of initial groove angle on FLC is strengthened by increasing sheet thickness. On the right side of FLC, the relation between limit strain points with different thicknesses is linear under one certain loading path. Thickness has decisive effect on through-thickness normal stress level and the changing trendy of through-thickness normal stress during calculation is different under different stress condition.     

A progressive approach to predict shot peening process parameters for forming integral panel of Al7050-T7451

In this paper, a progressive approach to predict the multiple shot peening process parameters for complex integral panel is proposed. Firstly, the invariable parameters in the forming process including shot size, mass flow, peening distance and peening angle are determined according to the empirical and machine type. Then, the optimal value of air pressure for the whole shot peening is selected by the experimental data. Finally, the feeding speed for every shot peening path is predicted by regression equation. The integral panel part with thickness from 2 mm to 5 mm and curvature radius from 3200 mm to 16000 mm is taken as a research object, and four experiments are conducted. In order to design specimens for acquiring the forming data, one experiment is conducted to compare the curvature radius of the plate and stringer-structural specimens, which were peened along the middle of the two stringers. The most striking finding of this experiment is that the outer shape error range is below 3.9%, so the plate specimens can be used in predicting feeding speed of the integral panel. The second experiment is performed and results show that when the coverage reaches the limit of 80%, the minimum feeding speed is 50 mm/s. By this feeding speed, the forming curvature radius of the specimens with different thickness from the third experiment is measured and compared with the research object, and the optimal air pressure is 0.15 MPa. Then, the plate specimens with thickness from 2 mm to 5 mm are peened in the fourth experiment, and the measured curvature radius data are used to calculate the feeding speed of different shot peening path by regressive analysis method. The algorithm is validated by forming a test part and the average deviation is 0.496 mm. It is shown that the approach can realize the forming of the integral panel precisely.     

机载托架自动校准系统的设计与实现

为了解决机载托架传统校准方法精度低、耗时、费力等问题,设计了一种高精度、高效率并且操作简单的成品托架自动校准系统。该系统运用调平精度较高的"循环多次"最高点不动调平方法,建立高精度机载托架校准的静力学数学模型,运用VC与Matlab的COM接口编程技术开发机载托架自动校准系统,并建立良好的人机交互界面。试验结果表明,利用该方法对机载托架进行校准,无论是校准精度还是校准效率都较传统方法有很大提高。     

一种基于虚拟页地址映射的NAND Flash管理算法

本文提出了一种基于虚拟页地址映射的NAND Flash管理算法.该算法通过定义坏块表、对应表等结构，以及设计的坏块替换策略和虚拟页地址到实际物理页地址的转换算法，实现上层软件采用虚拟地址对NAND Flash的无坏块连续页地址访问.该算法是一种高效的地址映射算法，能高效地对数据进行索引，占用SRAM空间较少，使系统达到高性能，并使得闪存使用的更加稳定持久.     

多臂空间机器人的视觉伺服与协调控制

针对多臂空间机器人自主目标抓捕任务，首先建立多臂空间机器人的运动模型和其与目标的相对运动模型，采用Kane方法建立多臂空间机器人的动力学模型；其次，研究基于视觉伺服的机械臂在线轨迹规划算法，并引入零反作用机动，消除机械臂运动对平台姿态的扰动；再次，在不使用零反作用机动功能时，分别使用基于角动量前馈补偿的协调控制算法和逆动力学方法设计了协调控制器，在机械臂运动时保持平台姿态和相对目标的位置。最后，开发了基于Matlab的仿真软件MASS（多臂空间机器人仿真），仿真结果校验了上述方法的有效性。     

ADI方法求解完全跨声速非定常小扰动方程

本文修改了Whitlow的ADI格式,以便求解另一变形的完全跨声速小扰动方程。本文给出的NACA64A006和NACA0012翼型的非定常跨声速流动的计算结果与其它数值结果和实验结果的比较表明本文格式是合理的且便于实际应用的。     

关于一维非定常气─固二相流特征理论的讨论

本文研究了一维非定常气－团二相流的特征，对于目前常用的、包含一定近似的运动方程组，它有两个虚部很小的复根，研究表明这种很小的虚部出现与方程中引入的近似有关。从十多个算例的结果看，这样的虚部不影响人们在工程计算中用该方程组求解初值问题。针对具有上述特征的气－团二相流方程组，本文发展了一种类特征线方法，它保留了双曲型方程特征线方法的若干优点，但它允许方程的特征根中有微小的虚部。含灰气体激波管流动的计算表明，类特征线法具有精度高、数值耗散和弥散小等优点     

精仪工作台定量调整的原理及方法

论述了可调结构仪器工作台的结构、调整原理和调整方法，并以三点支撑结构、锥面支撑结构仪器工作台表面与测量轴线垂直度的调整为例，具体地阐述了调整方法和步骤。     

热处理作业系统中安全性评价的AHP方法

本给出了系统安全性评价的AHP方法，叙述了该方法的基本步骤，并以沈阳某集团公司热处理弹簧厂评价的实例说明了该方法的有效性。