双轴连续旋转调制捷联惯导系统大失准角初始对准技术

由于可以补偿惯性器件在三个轴向上的输出误差，双轴旋转调制技术被广泛应用于捷联惯导系统(SINS)。选择了一种合理且实用的十六次序双轴转位方案，并对其调制原理和误差进行了分析。初始对准技术是捷联惯导系统的一项重要技术，其对准精度直接决定了后续导航的精度。在粗对准完成后，当姿态误差角较大时，后续的精对准误差模型呈非线性特性，故选择了滤波精度高、稳定性强的平方根容积Kalman滤波算法(SCKF)来解决这一问题。考虑到在实际对准过程中，量测噪声的统计特性易发生变化，将SCKF算法与Sage-Husa算法相结合，在传统Sage-Husa SCKF算法的基础上提出了一种改进的自适应滤波算法(ASCKF)。该算法采用QR分解来完成对噪声协方差的平方根矩阵估计，从而避免了传统Sage-Husa SCKF算法中所估噪声协方差矩阵不正定的问题。最后，通过仿真证实了ASCKF算法可被很好地应用于量测噪声统计特性发生变化的初始对准中。     

一种高精度小型化星敏感器设计

星敏感器是以恒星为参照系,以星空为工作对象的高精度空间姿态测量装置,提供准确的空间方位和基准,具有高精度、无漂移、工作寿命长等特点.针对星敏感器高精度和小体积的应用需求,基于小型化镜头设计、分体式结构、高集成度电路、"FP GA+ARM"软件等内容,提出了一种高精度小型化星敏感器,解决了狭小空间高度集成的小型化问题,实现了测姿0.6″(3σ)的高精度预期目标.星敏感器样机通过了试验考核,性能符合设计要求,具备全天球搜索恒星定姿的能力.     

基于频谱仪的脉冲调制信号功率校准技术研究

脉冲调制信号是雷达和数字通信系统中的一类重要信号。本文主要研究脉冲调制信号的功率测量方法,讨论并分析了脉冲调制信号的频谱特点,提出使用频谱分析仪实现脉冲调制信号的平均功率和峰值功率的测量,并采用正弦调幅法对频谱分析仪的测量结果进行验证。实验表明使用频谱仪测量脉冲调制信号功率简单易行且具有较高的测量精度。     

基于降维算法和等效杆长的可展结构精度分析

考虑铰链间隙和杆件尺寸误差的不确定性并通过概率统计方法对其进行研究,提出了一种基于单变量降维算法(UDRM)和等效杆长模型的可展结构精度分析方法。利用UDRM将可展结构的精度性能函数解耦为多个杆件尺寸误差的独立作用形式,建立精度分析模型。引入等效杆长模型,等效杆件替代原杆件进行精度计算。将铰链间隙与原始杆件尺寸误差合并到等效杆件的尺寸误差中,同时证明了等效杆长尺寸误差近似服从正态分布。以某卫星可展开天线为算例,结合高斯求积公式求解展开状态下精度指标的分布期望和方差。通过与蒙特卡罗模拟(MCS)和一次二阶矩(FOSM)法计算结果的对比验证了本文精度分析方法的正确性和高效性。     

Early analysis of precise orbit and clock offset determination for the satellites of the global BeiDou-3 system

Eight new-generation BeiDou satellites (BeiDou-3) have been launched into Medium Earth Orbit (MEO), allowing for global coverage since March 2018, and they are equipped with new hydrogen atomic clocks and updated rubidium clocks. Firstly, we analyzed the signals for the carrier-to-noise-density ratio (C/N0) and pseudorange multipath (MP) by using international GNSS (Global Navigation Satellite System) Monitoring and Assessment System (iGMAS) station data, and found that B1C has a lower C/N0, and B2a has the same level of C/N0 as the B1I and B3I signals. For pseudorange multipath, compared with the BeiDou-2 satellites, the obvious systematic variation of MP scatters related to the elevation angle is greatly improved for the BeiDou-3 and BeiDou-3e satellites signals. For the signals of the BeiDou-3 satellites, the order of the Root Mean Square (RMS) values of multipath and noise is B3I?<?B1I?<?B2a?<?B1C. Then, the comparison of the precise orbit determination and clock offset determination for the BeiDou-2, BeiDou-3, and BeiDou-3 experimental (BeiDou-3e) satellites was done by using 10 stations from iGMAS. The 3D precision of the 24?h orbit overlap is 24.55, 25.61, and 23.35?cm for the BeiDou-3, BeiDou-3e, and BeiDou-2 satellites, respectively. BeiDou-3 satellite has a comparable precision to that of the BeiDou-2 satellite. For the precision of clock offset estimation, the Standard Deviation (STD) of the BeiDou-3 MEO satellite is 0.350?ns, which is an improvement of 0.042?ns over that of the BeiDou-2 MEO satellite. The stabilities of the BeiDou-3 and BeiDou-3e onboard clocks are better than those of BeiDou-2 by factors of 2.84 and 1.61 at an averaging time of 1000 and 10,000?s, respectively.     

ZYTC600专用镗床精密转台微调机构设计与分析

为解决框架类零件的高位置度孔的精密镗削加工问题,研发了ZYTC600专用镗削机床.其精度指标优于现有的通用镗床(包括进口镗床),尺寸在500mm范围内,同轴度优于2μm,垂直度优于5μm,其中的关键部件双回转轴系分度精密转台采用了一套精密调整机构,可以实现0.2s”的精密调整,通过有限元分析得到其驱动刚度可达到800N/μm,可以满足加工需求.     

Sunspot activity and cosmic ray modulation at 1 a.u. for 1900–2013

The descent of sunspot cycle 23 to an unprecedented minimum of long duration in 2006–2009 led to a prolonged galactic cosmic ray (GCR) recovery to the highest level observed in the instrumental era for a variety of energetic charged particle species on Earth, over a wide range of rigidities. The remarkable GCR increase measured by several ground-based, balloon-borne, and detectors on a satellite is described and discussed. It is accompanied by a decrease in solar wind velocity and interplanetary magnetic field at 1 a.u., reaching the lowest values since measurements of the solar wind began in October 1963; the solar polar field strength (μT) measured at the Wilcox Solar Observatory (WSO) is also significantly reduced compared to prior cycles since the start of the program in 1976, the polar field in the northern hemisphere reversed in June 2012 and again in February 2014, that in the southern hemisphere reversed in July 2013. If updates of WSO data confirm the second reversal in northern solar hemisphere, it would pose a serious challenge to the Dynamo Theory. The long-term change in solar behavior may have begun in 1992, perhaps earlier. The physical underpinnings of these solar changes need to be understood and their effect on GCR modulation processes clarified. The study discusses the recent phenomena in the context of GCR modulation since 1900. These happenings affected our empirical predictions for the key parameters for the next two sunspot cycles (they may be progressively less active than sunspot cycle 24) but it enhanced support for our prediction that solar activity is descending into a Dalton-like grand minimum in the middle of the twentyfirst century, reducing the frequency of the coronal mass ejections; they determine the space weather affecting the quality of life on Earth, radiation dose for hardware and human activities in space as well as the frequency of large Forbush decreases at 1 a.u.     

压气机叶片型面精密数控铣加工技术应用研究

为了提高压气机叶片型面和进、排气边转接圆角的数控铣加工质量,在工艺、夹具、数控加工模型与程序以及检测方法等方面采取了攻关措施,减小了叶片型面精铣加工的变形,实现了叶身型面的精密铣削加工,对型面采用毡轮修光去除铣削痕迹后,经过3坐标、小半径投影仪等设备的测量,进、排气边转接圆角的形状和型面轮廓度、位置度各项要求的加工质量得到了质的提升,其合格率由20％提高到75％以上,加工效率和刀具耐用度提高1倍以上,使叶身型面精密铣削技术具备了精品叶片批量生产的工程化应用技术基础.     

飞机装配质量数字化检测技术研究及应用

针对飞机装配过程质量评价对数字化测量技术的需求,开展了面向飞机装配的数字化测量特征设计、测量方案设计、多系统异构测量场构建、测量误差分析与修正等技术研究,并以表面类、内部结构特征、大部件对接和活动部件装配质量的控制为例,阐述了测量设备选型、整体测量场的构建方法及其应用效果.     

多弧离子镀技术及其在高精度仪表中的应用

介绍了多弧离子镀技术,包括其技术原理、技术特点以及主要工艺参数,阐述了多弧离子镀技术在高精度仪表轴承零件表面改性方面的应用和存在的技术问题,对多弧离子镀技术在高精度仪表中的应用前景作出展望.