复合固体推进剂细观结构建模及脱黏过程数值模拟

为研究复合固体推进剂损伤演化规律,基于分子动力学颗粒填充算法构建了HTPB(hydroxyl terminated polybutadiene)推进剂细观结构模型,通过在AP(ammonium perchlorate)颗粒/HTPB基体界面处引入黏接接触替代传统的黏接单元,并基于Hooke Jeeves的参数优化算法反演得到颗粒/基体界面处内聚力模型参数,利用双线性和自定义指数型损伤内聚力模型模拟了AP颗粒和HTPB基体黏接界面处损伤的萌生、发展、聚合直至宏观裂纹破坏的过程。通过数值仿真与实验结果对比发现,指数型损伤内聚力模型比双线性模型能更准确描述推进剂单轴拉伸过程中颗粒与HTPB基体界面间脱黏过程。最后对比了多阶段加载实验结果与仿真结果曲线,发现两者变化趋势基本一致,最大偏差仅为10%,验证了所建细观模型的可靠性及反演所得界面参数的准确性。      

基于有向图模型的民机航空电子系统故障诊断

结合民机航电系统外场可更换单元或模块（LRU/LRM）的故障模式及影响分析（FMEA）、故障树 分析和实时性要求,设计了基于时间故障传播图（TFPG）的系统故障诊断元模型和领域模型,研究了基于逻 辑和时间一致性检验的故障诊断算法,使用后向推理和可信度度量列出候选故障集。以飞行管理系统为例,构 造了其功能失效的TFPG 模型,并通过仿真验证了基于TFPG 的诊断在滤除级联效应和关联驾驶舱效应中的有 效性。     

Dynamic parametric modeling-based model updating strategy of aeroengine casings

For accurate Finite Element (FE) modeling for the structural dynamics of aeroengine casings, Parametric Modeling-based Model Updating Strategy (PM-MUS) is proposed based on efficient FE parametric modeling and model updating techniques regarding uncorrelated/correlated mode shapes. Casings structure is parametrically modeled by simplifying initial structural FE model and equivalently simulating mechanical characteristics. Uncorrelated modes between FE model and experiment are reasonably handled by adopting an objective function to recognize correct correlated modes pairs. The parametrized FE model is updated to effectively describe structural dynamic characteristics in respect of testing data. The model updating technology is firstly validated by the detailed FE model updating of one fixed–fixed beam structure in light of correlated/uncorrelated mode shapes and measured mode data. The PM-MUS is applied to the FE parametrized model updating of an aeroengine stator system (casings) which is constructed by the proposed parametric modeling approach. As revealed in this study, (A) the updated models by the proposed updating strategy and dynamic test data is accurate, and (B) the uncorrelated modes like close modes can be effectively handled and precisely identify the FE model mode associated the corresponding experimental mode, and (C) parametric modeling can enhance the dynamic modeling updating of complex structure in the accuracy of mode matching. The efforts of this study provide an efficient dynamic model updating strategy (PM-MUS) for aeroengine casings by parametric modeling and experimental test data regarding uncorrelated modes.     

Microstructural characterization and mechanical behavior analysis of 7075-T6 aluminum subjected to simulated lightning strikes

Aircrafts damages caused by lightning strikes have been known since the early days of aviation. However, the physical effects on the aircraft structure are still being investigated. This work seeks to evaluate the lightning strike effects in the aluminum alloy 7075-T6. Samples were submitted to lightning strike simulation in laboratory and the damages evaluated through characterization techniques. Ultrasound and profilometry tests have shown material loss to 0.272 mm depth in the damaged region. In addition, it was detected the material accumulation occurrence in the damage vicinity of the region. Below the damage, it was found a region where metallurgical changes were identified. The tensile and microhardness tests results have shown reduction in the percentage elongation and hardness increasing in the material affected by lightning. These results are corroborated by the X-Ray Diffraction (XRD) and Rietveld Method (red line) that indicated an increasing in dislocation density and micro-deformation in the material matrix. Optical microscopy results have shown the presence of microcracks on the normal and cross-section surface of the samples damaged. The Energy Dispersive X-Ray Spectroscopy (EDXS) and Electron Backscattered Diffraction Test (EBSD) found coarse intermetallic phases and precipitates compounds with dimensions greater than 1 μm in length. They were responsible for nucleation of the microcracks that propagate along the material grain boundaries.     

压气机转子叶片叶尖流场的低速模化设计

针对带进口导叶的高速压气机第1级转子叶片的叶尖流场进行了低速模化设计,为后续的低速压气机叶尖流场损失和失速测试试验做了准备.利用叶片造型和数值模拟方法,以保证高、低速压气机转子叶片表面压力系数及叶片排进、出口主要气动参数分布相似为目标,对高速原型压气机进行低速模化设计,包括调整流道形状,对叶型进行反复迭代,并在进口导叶和1级转子叶片的造型设计上突破了几何相似的限制.最后,对高低速压气机的几何、气动参数和流场结构进行了全面的计算对比分析,证明采用所提出的低速模化设计方法是成功的,实现了在流量系数相同的情况下,加工量因子和转子扩压因子分别为98.16%,94.95%的相似度.      

短距起飞/垂直降落发动机建模技术研究

参考常规双轴涡扇发动机数学模型,建立了适用于短距起飞/垂直降落(STOVL)飞机的变循环发动机部件级数学模型;通过特性外推,建立了轴驱动升力风扇数学模型;采用神经网络映射涵道总压损失的方法,建立了滚转喷管和外涵模型.根据STOVL发动机结构和部件变化特点,建立了稳态和动态共同工作方程.参照国外文献仿真数据进行设计点计算,并按照Bevilaqua提出方法开展了由常规涡轮风扇模式到悬停涡轮轴模式的过渡态仿真.仿真结果表明:建立的数学模型在悬停状态设计点和高空巡航点与国外文献数据相比误差均小于1.5%,推力达到悬停状态要求,符合STOVL发动机的设计特点,验证了该建模方法的有效性.      

翼伞系统纵向飞行性能分析

翼伞系统的飞行性能不仅取决于翼伞本身的气动特性,而且与安装角、伞绳长度、回收物阻力特征、翼载荷等系统参数密切相关。文章应用拉格朗日方程建立翼伞系统的纵向飞行力学模型,对翼伞系统进行飞行力学数值仿真,深入分析了系统参数以及开伞状态对翼伞系统纵向飞行性能的影响规律。结果表明：只有安装角在0°～20°时,翼伞系统才能达到稳定的滑翔状态,且安装角在4°～6°时对应两个稳定的滑翔状态,具体由开伞姿态和速度决定;伞绳特征长度的增加使系统的静稳定性增加;回收物的阻力特征增加6m2,翼伞系统的稳定滑翔角增加15°左右,而迎角减小不到1°;翼伞飞行速度随着翼载荷的增加而增加,其平方与回收物质量成正比。上述结论可为翼伞系统的工程实际应用提供参考。     

三角形机翼参数化有限元网格划分与调整方法

为缩短有限元建模周期,提高三角形机翼结构分析、设计与优化的效率疲,首先,以其满足预定气动性能的几何外形为输入,定义了易用的有限元节点与单元的编号规则;基于可设计的机翼内部构型参数及可变的有限元尺寸参数的设置,引入了翼肋贯穿截止准则以满足任意输入的内部构型的初步判断;借助自定义形状矩阵完成了节点布置与单元生成,进一步通过有限元网格细化完成了开口设置、翼肋贯穿位置修正及桁条建模.然后,基于已建立的有限元网格实现了内外侧副翼翼肋位置的小幅调整及旋转舵面的角度调整,以满足不同飞行状态下结构分析需求.最后,应用PCL语言开发了参数化建模模块,实例表明了方法的有效性和模块可靠性.      

Search for high-proper motion objects with infrared excess

The possibility of interstellar migration has been theorized during the past thirty years in the form of “Dysonships” that, using non-relativistic propulsion systems, are able to colonize the Galaxy in a relatively short time compared to the age of the Galaxy and consequently penetrate inside our solar system too. Observational evidence of this can be potentially obtained using the present state of the art of telescopes and related sensors, by following aimed searches and an expanded SETI protocol. Some transient and unrepeated radio signals recorded during standard SETI observations might be due to the transit of high-proper motion artificial sources of extraterrestrial origin, which are expected to show a very weak optical emission, a strong infrared excess and occasional high-energy bursts in the X and Gamma-ray wavelength ranges. Such artificial sources might show an interest to Earth by sending probes to visit it: such a possibility can be investigated scientifically as well.     

基于着色Petri网的维修作业建模与人机工效分析

基于着色Petri网和CPN Tools平台,研究了维修作业过程的建模方法,提出了维修作业过程建模方法与步骤,采用模特法计算每一步操作所需时间值,采用人体动作代谢能耗预测模型计算每个操作的能耗值,实现了维修作业建模与仿真、作业序列的控制以及维修人员工作负荷和工作时间的定量计算。以A320飞机前起落架轮胎拆卸作业为例,采用CPN Tools软件进行了维修作业建模和仿真模拟,验证了模型和方法的可行性与有效性。该方法引入了传统维修作业模型中没有涉及的人机工效因素,能够有效评价维修人员的作业舒适性。