Topology optimization in lightweight design of a 3D-printed flapping-wing micro aerial vehicle

Topology optimization is an effective method to obtain a lightweight structure that meets the requirements of structural strength. Whether the optimization results meet the actual needs mainly depends on the accuracy of the material properties and the boundary conditions, especially for a tiny Flapping-wing Micro Aerial Vehicle (FMAV) transmission system manufactured by 3D printing. In this paper, experimental and numerical computation efforts were undertaken to gain a reliable topology optimization method for the bottom of the transmission system. First, the constitutive behavior of the ultraviolet (UV) curable resin used in fabrication was evaluated. Second, a numerical computation model describing further verified via experiments. Topology optimization modeling considering nonlinear factors, e.g. contact, friction and collision, was presented, and the optimization results were verified by both dynamic simulation and experiments. Finally, detailed discussions on different load cases and constraints were presented to clarify their effect on the optimization. Our methods and results presented in this paper may shed light on the lightweight design of a FMAV.     

偏心撞击对撞击式喷嘴雾化特性的影响

为研究偏心撞击对撞击式喷嘴雾化特性的影响,建立了求解自燃推进剂冷态射流撞击雾化过程的数值模拟方案,计算了不同偏心度条件下的射流撞击雾化过程。采用树形自适应加密算法直接求解不可压Navier-Stokes方程组,由分段线性的流体体积(VOF)方法对流体界面进行捕捉。结果表明偏心撞击会导致雾场发生偏转,当无量纲偏心度E为1/8时,雾场偏转角度约为9.2°,应控制加工偏差小于该值。随着偏心度的增大,液膜的偏转角度增大,理论推导得到的液膜偏转角度要小于数值计算得到的液膜偏转角度。正心撞击时燃料与氧化剂流强峰值接近,雾场的流强分布呈单峰分布。当发生偏心撞击时,由于燃料与氧化剂部分射流未参与撞击导致流强峰值出现交错,雾场的流强分布呈双峰分布,混合比的空间分布发生较大改变。正心撞击时撞击点下游液滴的速度分布近似呈轴对称分布,而偏心撞击之后的速度分布则呈中心对称分布。偏心撞击导致的射流动量损失使得雾化性能变差,当无量纲偏心度E为1/8时,一甲基肼(MMH)的Sauter平均直径增大约4.8%,四氧化二氮(NTO)的Sauter平均直径增大约5.8%。      

涡轮基组合循环发动机分布式控制系统通信网络混合拓扑结构优化方法

涡轮机组合循环(Turbine based combined cycle,TBCC)发动机控制系统通信网络拓扑结构是其分布式控制系统方案设计的重要部分,优化网络拓扑结构可提高发动机推重比和控制系统可靠性。本文基于智能优化算法提出TBCC分布式控制系统网络拓扑结构优化方法。基于图论建立TBCC几何模型和网格模型,以重量和可靠性为优化性能指标,同时考虑发动机表面高温区域以及控制节点的工作可靠性,分别采用粒子群算法和遗传算法优化星形结构中智能中央节点位置、中央节点的环形拓扑结构,获得星形-环形混合拓扑结构。仿真实例表明,基于本文方法优化所得的混合拓扑结构相较于星形集中式控制结构,系统重量降低了51.9%。     

An innovative approach for integrated airline network and aircraft family optimization

The determination of optimal aerial transport networks and their associated flight frequencies is crucial for the strategic planning of airlines, as well as for carrying out market research, to establish target markets, and for aircraft and crew rostering. In addition, optimum airplane types for the selected networks are crucial to improve revenue and to provide reduced operating costs. The present study proposes an innovative approach to determine the optimal aerial transport network simultaneously with the determination of the optimum fleet for that network, composed of three types of airplanes (network and vehicle integrated design). The network profit is maximized. The passenger’s demands between the airports are determined via a gravitational model. An embedded linear programming solution is responsible for obtaining potential optimal network configurations. The optimum fleet combination is determined from a database of candidate aircraft designs via genetic algorithm. A truly realistic airplane representation is made possible thanks to accurate surrogate models for engine and aerodynamics is adopted. An accurate engine deck encompassing a compression map and an innovative engine weight calculation besides an aerodynamical artificial neural network module enable a high degree of accuracy for the mission analysis. The proposed methodology is applied to obtain the optimum network comprised of twenty main Brazilian airports and corresponding fleet.     

考虑辐射的化学平衡流驻点线解

本文用数值方法求解了化学平衡的高超声速粘性激波层驻点线流场。考虑了辐射和质量引射对流场的影响。辐射模型采用线和连续谱模型。文中讨论了引射率、头部半径、来流速度对壁面传热的影响。与有关文献结果比较表明,本文的方法是可行的。     

发动机质心测试系统软硬件设计

介绍了发动机质心测试系统的基本构成以及其软硬件的设计实现.     

关于疲劳裂纹扩展数学模型的参数寻优

本文通过引入工程设计中的优化方法，分别对室内空气环境下铝合金（ＬＹ１２－ＣＺ）材料疲劳裂纹扩展的数学模型，以及环境条件下（３．５％ＮａＣｌ水溶液浸泡）该材料腐蚀疲劳裂纹扩展的数学模型进行了探讨。在已知标准试样在不同的环境下疲劳裂纹扩展实验ｄａｄＮｉ，ΔＫｉ的条件下，采用优化方法进行参数寻优，可方便地得到与其对应的疲劳裂纹扩展的ｄａｄＮ～ΔＫ最优数学模型     

质量矩导弹的神经网络及自适应非线性控制

本文对质量矩控制导弹的动力学方程简化和控制系统的设计进行了研究。详细阐述了所提出的控制方法，介绍了径向基单隐层神经网络进行误差补偿的算法原理，用Lyapunov理论证明了所采用方法的稳定性。在给出了质量矩导弹的六自由度动力学方程和简化后的方程后，用所提出的方法设计控制系统。通过仿真分析，得出了本文所提出的方法具有较好的误差补偿能力的结论。     

满足约束的Gn连续过渡曲面的构造

在Erich Hartmann提出的由两基曲面线性组合构造G^n连续过渡曲面方法的基础上，针对该方法存在很难找到合适的参数变换的问题，提出了一种基于基曲面局部区域重新参数化构造G^n连续过渡曲面的方法。通过对基曲面上切触线附近区域部分曲面重新参数化，再由重新参数化局部基曲面线性组合构造G^n连续过渡曲面。这样将两基曲面间构造过渡曲面的问题转化为在重新参数化局部基曲面间构造过渡曲面。以构造G^1连续的翼身融合面为例，讨论了满足约束要求条件时G^2连续过渡面的构造方法。即先对基曲面上过渡切触线附近的局部区域进行重新参数化，后通过优化求解来确定比例因子和偏移量、平衡因子和调配因子，使过渡曲面满足前后边条线约束，最后利用线性组合来构造G^2连续的过渡面。约束过渡曲面的形状可通过改变重新参数化基曲面的大小来调整．     

基于粒子群优化算法的不完全数据的处理

不完全信息下的数据挖掘是一个困难的问题，但它在实际决策中是不可避免的。在介绍几种处理方法的基础上，提出了基于粒子群优化算法的处理方法。对适应函数进行了讨论，实例表明该方法比较有效。