激光功率与底面状态对选区激光熔化球化的影响

为研究激光功率与底面状态对选区激光熔化熔池流动的影响，基于离散单元法建立了选区激光熔化铺粉模型，采用粒径分布与实验相符的马氏体时效钢粉末分别铺展到平坦底面和增材底面上，将计算获得的粉末分布导入到基于有限体积法建立的选区激光熔化熔池计算流体力学模型中，研究激光功率和基板底面粗糙度对熔池流动和熔道表面形貌的影响。采用激光单道扫描实验验证铺粉模型和选区激光熔化模型。结果表明：随着激光功率的降低，单位长度的球化数量增加；由于增材底面使熔池润湿性变差，同时又对熔池流动行为产生扰动，使得增材粗糙底面上熔道的球化数量增加。选区激光熔化铺粉模拟及激光单道扫描模拟结果与实验结果吻合较好。本研究可为选区激光熔化工艺中工艺参数的选择提供理论指导。     

考虑轨道摄动的外热流计算分析

为改进传统外热流算法未考虑外热流经多次反射后的吸收和国外商业软件未考虑轨道摄动及太阳矢量变化对外热流的影响等不足,重新定义了外热流角系数和外热流辐射传递因子,综合SGP4轨道模型和Gebhart方法,给出了考虑摄动等因素的辐射传递因子和轨道外热流计算模型,以及相应的计算流程。通过仿真分析论证了考虑多次反射及摄动等因素的重要性。     

基于数值模拟的翼身融合布局飞机上悬式发动机布置技术

发动机进排气对飞机气动特性具有重要影响。为了评估翼身融合布局（BWB）飞机上悬式发动机不同布置方式对全机气动特性的影响，首先开展了发动机短舱进排气与全机流场耦合的数值模拟技术研究，验证了计算方法的正确性。在此基础上，针对发动机安装于翼身升力面之上的BWB运输类飞机，开展飞机巡航飞行条件下，发动机不同支撑高度下沿流向及展向不同安装位置的进排气与全机流场耦合数值模拟，评估发动机不同布置方式对全机气动特性的影响，形成发动机不同布置方式影响的规律性结论。     

涡桨飞机螺旋桨滑流气动干扰效应及流动机理

螺旋桨滑流对飞机各气动部件的干扰是涡桨飞机气动设计中面临的难点之一。以某双发涡桨支线客机为对象，采用数值模拟手段分析了滑流对机翼、平尾、垂尾的影响及其流动机理。计算采用基于动态面搭接网格技术的非定常方法，气动力与表面压力分布的计算结果均与实验值吻合良好。研究结果表明：在滑流影响下，全机升力和阻力有所增加，升阻比和纵向静稳定度有所降低，并在无侧滑状态下产生了滚转力矩和偏航力矩；在不同展向位置，滑流对机翼表面流动分离的影响存在显著的差异。在螺旋桨下行运动一侧，滑流的旋转减小了当地迎角，同时桨后气流速度较高，翼面流动分离被有效抑制。在螺旋桨上行运动一侧，滑流的旋转增大了当地迎角，而且桨后气流速度较低，因而翼面流动分离并未得到明显改善；在中小迎角下，滑流对背景飞机平尾当地的动压没有产生影响，但增加了下洗角变化率，进而导致平尾效率降低；垂尾的侧力与偏航力矩是由滑流的侧洗引起的，而滑流的侧洗又与左右两侧机翼升力分布的不对称性有关。     

斜激波极值规律的边界层影响

采用边界层理论与斜激波/膨胀波精确算法，建立一种结合Eckert参考温度法和Illingworth-Stewartson变换法优势的边界层权重算法，用于研究超声速黏性楔面边界层位移厚度对斜激波极值规律的影响。分别应用层流Navier-Stokes方程和湍流Navier-Stokes方程的CFD解算器对边界层新模型进行了算例精度评估。在来流马赫数为1.2~2.4和楔面角为3°~20°的范围内，压强比的相对误差小于0.1%。计入层流与湍流边界层影响的理论模型研究表明，边界层影响使得最优马赫数增加；对于层流边界层，最优马赫数增量约为0.001 5~0.003 3；对于湍流边界层，最优马赫数增量约为0.002 8~0.006 1。     

航空发动机进气支板电热防冰试验

为了研究电加热防冰的效果,开展了小型航空发动机进气支板的电加热防冰试验。结合该型号发动机进气支板的结构特点,设计了3种电热防冰加热布置方式,分别在支板沿轴向的不同位置采用1~3个电加热棒作为防冰热源。通过模拟不同的发动机进气结冰环境参数和电加热功率,在冰风洞中对3种电加热方式进行了防冰试验研究。通过布置在支板外表面的温度测点记录了防冰过程中支板表面的瞬态温度变化,分析了支板防冰过程中表面温度的变化特点。防冰试验研究了热源总功率、热源布置方式、液态水含量以及来流温度对支板防冰性能的影响。试验结果表明,合理的电加热方式可以取得较好的防冰效果,同时避免支板后部的溢流水结冰。     

运载火箭尾段防热/承载一体化热防护系统设计及性能分析

先进热防护技术是可重复使用运载火箭研制的关键技术之一,具有高结构效率的防热/承载一体化热防护系统是运载火箭极具潜力的备选热防护方案。本文系统地总结了可重复使用运载火箭尾舱段防热和承载两方面的设计要求,设计了一种全复合材料防隔热/承载一体化热防护系统。开展了运载火箭尾段一体化热防护系统设计,进行了代表性单胞结构的高温环境地面试验,揭示了复合材料一体化热防护系统的防隔热机理。同时施加力学和热流载荷,利用有限元方法对运载火箭尾段进行了热力耦合分析,获得了尾段结构的温度场、应变场和应力场。结果表明:在典型载荷工况下一体化热防护系统内壁温度保持在89.2℃以下,内部最大应力不超过9.53 MPa,安全系数达到1.89。     

Experimental investigation and correlation development of jet impingement heat transfer with two rows of aligned jet holes on an internal surface of a wing leading edge

Extensive experimental studies on the heat transfer characteristics of two rows of aligned jet holes impinging on a concave surface in a wing leading edge were conducted, where50000 Rej 90000, 1.74 H/d 27.5, 66° a 90°, and 13.2 r/d 42.03. The finding was that the heat transfer performance at the jet-impingement stagnation point with two rows of aligned jet holes was the same as that with a single row of jet holes or the middle row of three-row configurations when the circumferential angle of the two jet holes was larger than 30°. The attenuation coefficient distribution of the jet impingement heat transfer in the chordwise direction was so complicated that two zones were divided for a better analysis. It indicated that: the attenuation coefficient curve in the jet impingement zone exhibited an approximate upside-down bell shape with double peaks and a single valley; the attenuation coefficient curve in the non-jet impingement zone was like a half-bell shape, which was similar to that with three rows of aligned jet holes; the factors,including Rej, H/d and r/d, affected the attenuation coefficient value at the valley significantly.When r/d was increased from 30.75 to 42.03, the attenuation rates of attenuation coefficient increased only by 1.8%. Consequently, experimental data-based correlation equations of the Nusselt number for the heat transfer at the jet-impingement stagnation point and the distributionof the attenuation coefficient in the chordwise direction were acquired, which play an important role in designing the wing leading edge anti-icing system with two rows of aligned jet holes.     

Aerothermodynamic and stability analyses of a deployable re-entry capsule

Recent research projects, in the field of atmospheric re-entry technology, are focused on the design of deployable, umbrella-like Thermal Protection Systems (TPSs). These TPSs are made of flexible high temperature resistant fabrics, folded at launch and deployed in space for de-orbit and re-entry operations. In the present paper two possible sphere–cone configurations for the TPS have been investigated from an aerodynamic point of view. The analyzed configurations are characterized by the same reentry mass and maximum diameter, but have different half-cone angles (45° and 60°). The analyses involve both the evaluation of thermal and aerodynamic loads and the assessment of the capsule longitudinal stability. The aerothermodynamic analysis has been performed for the completely deployed heat shield in transitional and continuum regimes, while the longitudinal stability has been analyzed in free molecular, transitional and continuum regimes, also taking into consideration the heat shield deployment sequence at high altitudes.     

跨声速流自发凝结水滴的测量

应用基于多波长消光法原理发展的光学探针，测量了跨声速风洞中不同马赫数湿空气流自发凝结形成的水滴尺寸及浓度，并给出了实验结果