Heat transfer characteristics in a narrow confined channel with discrete impingement cooling

Heat transfer characteristics in a narrow confined channel with discrete impingement cooling were investigated using thermal infrared camera. Detailed heat transfer distributions and comparisons on three surfaces with three impact diameters were experimentally studied in the range of Reynolds number of 3000 to 30000. The experimental results indicated that the strong impingement jet leaded to a high strength heat transfer zone in the ΔX=±2.5D_j range of the impact center,which was 1.3–...     

二氧化碳射流下孔型对气膜冷却特性影响的实验研究(英文)

This article presents the data about heat transfer coefficient ratios, film cooling effectiveness and heat loads for the injection through cylindrical holes, 3-in-1 holes and fanned holes in order to characterize the film cooling performance downstream of a row of holes with 45° inclination and 3 hole spacing apart. The trip wire is placed upstream at a distance of 10 times diameter of the cooling hole from the hole center to keep mainstream fully turbulent. Both inlet and outlet of 3-in-1 holes have a 15° lateral expansion. The outlet of fanned holes has a lateral expansion. CO2 is applied for secondary injection to obtain a density ratio of 1.5. Momentum flux ratio varies from 1 to 4. The results indicate that the increased momentum flux ratio significantly increases heat transfer coefficient and slightly improve film cooling effectiveness for the injection through cylindrical holes. A weak dependence of heat transfer coefficient and film cooling effectiveness, respectively, on momentum flux ratio has been identified for the injection through 3-in-1 holes. The in- crease of the momentum flux ratio decreases heat transfer coefficient and significantly increases film cooling effectiveness for the injection through fanned holes. In terms of the film cooling performance, the fanned holes are the best while the cylindrical holes are the worst among the three hole shapes under study.     

Numerical Study of Flow and Heat Transfer Characteristics of Impingement/Effusion Cooling

Three-dimensional numerical simulation is carried out to investigate the flow and heat transfer characteristics of impingement/effusion cooling systems. The impingement/effusion holes are arranged on two parallel perforated plates respectively in a staggered manner. Every effusion hole has an inclined angle of 30° with respect to the surface. The two parallel plates are spaced three times the diameter of the effusion hole. The ratio of center-to-center spacing of adjacent holes to the diameter of the effusi...     

Experiments of flow and heat transfer performances for air-cooling laminated turbine vane

Flow resistance and heat transfer coefficients of typical double wall laminated film cooling configuration within a turbine vane were experimentally studied.The specimen was in large scale,and made of transparent organic glass.Laminated configuration consisted of double wall laminates,pin-fins,staggered arrays of impingement and film holes.The number ratio of impingement holes,pin-fins and film holes was2∶1∶1.Five experiment vanes were installed in static cascade,and experiments were carried out under constant heat flux.Re of internal cooling air in the experiment was from 104 to 2×105,and Re of external fluid was from 105 to 3×105.The experiment results show that flow resistances of front channel and back channel of the vane are in the same level,and both of them decrease as Re of cooling air increases.Nuof front channel is slightly higher than that of back channel.Both of them increase as Re of cooling air increases.And experiment results were obtained from experiment vanes were compared with that obtained from laminated flat plates,and the tendency of the results agrees well.     

Numerical investigation of transcritical liquid film cooling in a methane / oxygen rocket engine

Transcritical film cooling was investigated by numerical study in a methane cooled methane/oxygen rocket engine.The respective time-averaged Navier-Stokes equations have been solved for the compressible steady three-dimensional(3-D) flow.The flow field computations were performed using the semi-implicit method for pressure linked equation(SIMPLE) algorithm on several blocks of nonuniform collocated grid.The calculation was conducted over a pressure range of 202 650.0 Pa to 1.2×107 Pa and a temperature range of 120.0 K to 3 568.0 K.Twenty-nine different cases were simulated to calculate the impact of different factors.The results show that mass flow rate,length,diameter,number and diffused or convergence of film jet channel,injection angle and jet array arrangements have great impact on transcritical film cooling effectiveness.Furthermore,shape of the jet holes and jet and crossflow turbulence also affect the wall temperature distribution.Two rows of film arranged in different axial angles and staggered arrangement were proposed as new liquid film arrangement.Different radial angles have impact on the film cooling effectiveness in two row-jets cooled cases.The case of in-line and staggered arrangement are almost the same in the region before the second row of jets,but a staggered arrangement has a higher film cooling effectiveness from the second row of jets.     

Internal Heat Transfer Characteristics of Lamilloy Configurations

A transient measurement technique by using narrow-band thermochromic liquid crystal （TLC） is employed to determine temperature and heat transfer coefficient （HTC） distribution on inner surfaces of the typical lamilloy configurations. With this technique, both local HTC distribution and average HTC distribution could be obtained. The experimental results indicate that the variation of the porosity ratio, the one that the area of impingement holes divided by that of the plate, has a great effect on the HTC distribution on the inner surfaces. Heat exchange of inner surfaces varies directly as the porosity ratio. The impingement Reynolds number ranges from 20 000 to 50 000. The average HTC of inner surfaces bears a linear relationship with the Reynolds number.     

Effect of an end plate on surface pressure distributions of two swept wings

A series of wind tunnel tests was conducted to examine how an end plate affects the pressure distributions of two wings with leading edge(LE) sweep angles of 23° and 40°. All the experiments were carried out at a midchord Reynolds number of 8×10~5, covering an angle of attack(AOA) range from -2° to 14°. Static pressure distribution measurements were acquired over the upper surfaces of the wings along three chordwise rows and one spanwise direction at the wing quarter-chord line. The results of the tests confirm that at a particular AOA, increasing the sweep angle causes a noticeable decrease in the upper-surface suction pressure. Furthermore, as the sweep angle increases, the development of a laminar separation bubble near the LEs of the wings takes place at higher AOAs. On the other hand, spanwise pressure measurements show that increasing the wing sweep angle results in forming a stronger vortex on the quarter-chord line which has lower sensitivity to AOA variation and remains substantially attached to the wing surface for higher AOAs than that can be achieved in the case of a lower sweep angle. In addition, data obtained indicate that installing an end plate further reinforces the spanwise flow over the wing surface, thus affecting the pressure distribution.     

Experimental validation of a new morphing trailing edge system using Price – Païdoussis wind tunnel tests

This paper presents the design and manufacturing of a new morphing wing system carried out at the Laboratory of Applied Research in Active Controls, Avionics and AeroServoElasticity(LARCASE) at the ETS in Montréal. This first version of a morphing wing allows the deformation of its trailing edge, denote by Morphing Trailing Edge(MTE). In order to characterize the technical impact of this deformation, we compare its performance with that of a rigid aileron by testing in the LARCASE's price-Pa?doussis subsonic wind tunnel. The first set of results shows that it is possible to replace an aileron by a MTE on a wing, as an improvement was observed for the MTE aerodynamic performances with respect to the aileron aerodynamic performances.The improvement consisted in the fact that the drag coefficient was smaller, and the lift-to-drag ratio was higher for the same lift coefficient.     

Experimental investigation on boiling heat transfer characteristics of Al_2O_3-water nanofluids in swirl microchannels subjected to an acceleration force

Experiments were carried out to investigate the boiling heat transfer characteristics of Al_2O_3-water nanofluids in swirl microchannels under terrestrial gravity and acceleration fields. A centrifuge with a two-meter long rotational arm was used to simulate the acceleration magnitude up to 9 g and three various acceleration directions. Three test sections with different geometric parameters were applied. The volume concentration of Al_2O_3 nanoparticles with an average diameter of 13 nm was varied from 0.07% to 0.1%. The mass flow rate and vapor quality were in ranges of 3–6 kg/h and 0.4–1.0%, respectively. The effects of the mass flow rate, microchannel aspect ratio,vapor quality, nanoparticle volume concentration, and acceleration direction and magnitude were analyzed in a systematic manner. Experimental results showed that the acceleration direction and magnitude had significant influences on the boiling heat transfer. The heat transfer under configuration C was found to be superior to that under configurations A and B. Moreover, the heat transfer coefficient increased with increases of the mass flow rate and the volume concentration and decreased with the aspect ratio.     

Effect of a transverse plasma jet on a shock wave induced by a ramp

We conducted experiments in a wind tunnel with Mach number 2 to explore the evolution of a transverse plasma jet and its modification effect on a shock wave induced by a ramp with an angle of 24°. The transverse plasma jet was created by arc discharge in a small cylindrical cavity with a 2 mm diameter orifice. Three group tests with different actuator arrangements in the spanwise or streamwise direction upstream from the ramp were respectively studied to compare their disturbances to the shock wave. As shown by a time-resolved schlieren system, an unsteady motion of the shock wave by actuation was found: the shock wave was significantly modified by the plasma jet with an upstream motion and a reduced angle. Compared to spanwise actuation, a more intensive impact was obtained with two or three streamwise actuators working together. From shock wave structures, the control effect of the plasma jet on the shock motion based on a thermal effect, a potential cause of shock modification, was discussed. Furthermore, we performed a numerical simulation by using the Improved Delayed Detached Eddy Simulation(IDDES) method to simulate the evolution of the transverse plasma jet plume produced by two streamwise actuators. The results show that flow structures are similar to those identified in schlieren images. Two streamwise vortices were recognized, which indicates that the higher jet plume is the result of the overlap of two streamwise jets.     

半封闭通道射流冲击换热特性的实验

运用红外热像仪测试技术对半封闭通道单、双排孔射流冲击冷却进行了热像显示试验,总结了各种流动参数和几何参数对局部换热特性的影响规律:对于单排垂直射流,冲击冷却效果随冲击雷诺数的增加、孔间距与直径比的减小而得到提高,冲击间距比为2时换热效果最好;冲击孔中心线向通道封闭一侧倾斜后,射流冲击冷却的范围变窄,当冲击间距比大于2时驻点区的对流换热能力明显降低;对于双排冲击射流,在较小的冲击射流雷诺数和较大的冲击间距比下,后排射流的冲击换热效果要逊于前排射流。      

射流孔交错偏置排布下的楔形凹表面对流换热数值研究

通过三维数值模拟的方法研究了射流孔交错偏置排布下的楔形凹表面对流换热,在射流孔偏置间距比（L/d）为0~2.5、射流孔距凹腔前缘间距比（H/d）为6~12、射流冲击雷诺数（Re）为10000~28000的研究参数下,研究结果表明射流孔交错偏置排布在凹腔中诱导复杂的涡流,对应于射流冲击驻点区的局部表面传热系数得到增强;相对于直线排布的射流孔,小射流孔交错偏距比能够使得凹腔前缘附近沿弦向的展向平均努塞尔数相对射流孔直线排布方式有所改善,随着射流孔交错偏距比增加,沿弦向的展向平均努塞尔数最大值所对应的弦向位置逐渐向凹腔前缘下游迁移.为了在保持凹腔前缘对流换热能力不受到显著削弱的前提下,改善凹腔前缘附近的射流冲击对流换热能力,射流孔交错偏距比宜选择在1倍射流孔直径左右.      

密集型阵列冲击射流换热特性实验

设计了多种不同几何参数的阵列射流冲击孔实验件,利用红外热像仪对其冲击冷却进行了热像显示实验,获得了冲击射流雷诺数和几何参数对局部对流换热特性的影响规律.结果表明:①对流换热系数随着射流雷诺数R_ej的增加而逐渐增大;②随着孔间距的或者冲击间距的增大,冲击冷却的对流换热效果逐渐减弱;③当孔间距与孔径之比在3～5时,顺排阵列射流的强化换热效果优于叉排,而当孔间距与孔径之比为2时,在阵列射流上游叉排排布的强化换热效果优于顺排,而在下游则顺排排布的强化换热效果占优.      

带有加强肋的涡轮机匣排孔冲击连腔结构内部换热特性研究

为获得涡轮机匣内部表面换热系数分布数据,以带有加强肋的排孔冲击连腔结构为对象进行了瞬态液晶实验。研究了不同射流雷诺数（Re=5.1×10³~1.1×10⁴）、冲击间距比（2.5,5.0,7.5）及轴向间距比（4.0,9.0,14.0）对靶面努塞尔数的影响规律。实验结果表明：增大射流雷诺数对靶面平均努塞尔数的提升最显著。随着冲击间距比的增大,靶面平均努塞尔数逐渐减小,但这种换热削弱效果局限在距冲击驻点2D~3D（D为冲击孔直径）范围内,其它区域的变化很小。在靠近前后端壁的局部区域,表面努塞尔数随冲击间距比的增大而增大。轴向间距比的改变不会影响无出流孔靶面的换热情况,对于有出流孔靶面而言,轴向间距比为9.0的结构换热效果最好。Re=5.1×10³条件下,轴向间距比为9.0结构在有出流孔靶面上的平均努塞尔数相比4.0和14.0结构分别增大了5.7%和8.1%,并且随雷诺数增大,增幅越大。     

窄通道内冲击冷却局部换热特性的瞬态液晶测量

 为了深入了解涡轮叶片中冲击窄通道内的换热特性,采用热色液晶瞬态测量技术测量了冲击窄通道内全表面换热系数,获得了不同冲击雷诺数Re、相对冲击孔间距S/d以及有无气膜孔出流时通道内各表面的换热系数分布规律。结果表明：冲击通道内各个面的换热系数均随雷诺数的增加而增加,其中冲击靶面的平均换热系数最大,在雷诺数较大时,冲击面的平均换热系数要比冲击侧面的大;气膜孔出流和相对冲击孔间距增大均会使冲击侧面和冲击面的平均换热系数明显减小,而对冲击靶面平均换热系数的影响却较小;各个面上受气流直接冲击的区域换热系数最大,同时冲击孔和气膜孔附近区域的换热系数也很大。     

Unsteady analysis of jet impingement under vibration conditions

The vibration of thermodynamic machinery will affect its cooling system. In this research, a high-resolution simulation of jet impingement was performed to quantify the unsteady turbulent convection under vibration conditions. A newly developed Self-Adaptive Turbulence Eddy Simulation(SATES) method was used. The Reynolds number was Re = 23000, the jet-towall distance was fixed at H/D = 2, and the vibrating frequency of the impinging wall f varied from 0 to 200 Hz. Compared with the static wall c...     

高压涡轮机匣加强肋表面换热特性试验

针对高压涡轮叶尖间隙主动控制机匣的多层结构,重点分析了机匣内部加强肋和安装螺栓共同组成的基本换热单元,利用热膜法研究了加强肋表面的局部和平均传热系数,得到了不同进气状态、加强肋高度对传热系数的影响规律。研究发现:冲击靶面传热系数随着冲击雷诺数的增长而增大,但传热系数的增长速率随着冲击雷诺数的增大而缓慢降低。3排冲击射流工况中,靠近出流位置的加强肋表面平均传热系数最高。试验结果表明,加强肋表面的传热系数受到加强肋高度和冲击雷诺数耦合作用。在高雷诺数时,增加加强肋高度带来的换热强化效果更加明显。      

高压涡轮主动间隙控制机匣内部换热特性试验

针对高压涡轮叶尖主动间隙控制（ACC）机匣中的典型换热结构,利用试验研究了多层机匣结构中内斜向冲击射流的局部换热特征,重点分析了进口雷诺数（10000~24000）、冲击孔入射角度（30°,45°,60°）、冲击孔直径（1.0,1.5,2.0mm）等参数对带肋机匣表面局部和平均传热系数的影响规律.研究中发现加强肋的存在显著影响了机匣表面局部传热系数,同时由于冲击射流局部强化换热作用,多层机匣内表面不同位置的传热系数相差很大.试验结果表明:随着冷气进口雷诺数的增加,机匣加强肋表面局部和平均传热系数均提高.在研究参数范围内,冲击孔直径为2.0mm,孔数为23的情况下能够获得最佳的换热效果;相比30°和60°冲击孔入射角度,冲击孔入射角度为45°能获得更好的换热效果.      

半封闭通道射流冲击孔流量系数的实验

对半封闭通道射流冲击孔的流量系数进行了实验研究,针对单排、双排冲击孔结构,在变化各种几何参数及流动参数的情况下,较为系统地获得了射流孔展向间距与射流孔直径之比、射流孔流向间距与射流孔直径之比、射流冲击间距与射流孔直径之比、射流孔倾角等因素对于流量系数随射流雷诺数的变化曲线.通过对比分析,讨论了各种因素对流量系数的影响.