机载单站只测向定位最优机动研究

概述了机载单站只测向定位最优机动求解算法，研究了基于最大方位角变化率准则下的观测机机动轨迹，得到理论上的最优定位机动，并结合实际运用，分析出两种近似最优的机动：“一”形（直线形）机动和S形机动，通过仿真，验证了这2种机动方式在一定条件下可以等效于最优机动，具有良好的定位效果。     

多功能水冷壁排管爬壁机器人的研制

介绍了一种新研制开发的永磁吸附式双履带结构爬壁机器人，主要应用于火力发电站的大型排管锅炉中的水冷壁排管壁面的清扫和检测，并能够在检测到壁面厚度小于预置的极限值处发出报警信号、打标记，具有较高的推广应用价值。文中阐述了该机器人的结构、磁路的优化设计、自动测厚、打标系统和控制系统的研制。目前，该机器人已经经过多次现场试验。各项指标均已达到设计要求。     

Global aerodynamic design optimization based on data dimensionality reduction

In aerodynamic optimization, global optimization methods such as genetic algorithms are preferred in many cases because of their advantage on reaching global optimum. However, for complex problems in which large number of design variables are needed, the computational cost becomes prohibitive, and thus original global optimization strategies are required. To address this need, data dimensionality reduction method is combined with global optimization methods, thus forming a new global optimization system, aiming to improve the efficiency of conventional global optimization. The new optimization system involves applying Proper Orthogonal Decomposition (POD) in dimensionality reduction of design space while maintaining the generality of original design space. Besides, an acceleration approach for samples calculation in surrogate modeling is applied to reduce the computational time while providing sufficient accuracy. The optimizations of a transonic airfoil RAE2822 and the transonic wing ONERA M6 are performed to demonstrate the effectiveness of the proposed new optimization system. In both cases, we manage to reduce the number of design variables from 20 to 10 and from 42 to 20 respectively. The new design optimization system converges faster and it takes 1/3 of the total time of traditional optimization to converge to a better design, thus significantly reducing the overall optimization time and improving the efficiency of conventional global design optimization method.     

飞机电气系统参数测试标准实施中问题分析

结合本标准宣贯、研讨会上所提供的信息,分析了飞机电气系统参数测试标准在实际应用中存在的一些问题,并对瞬态电压和频率调制率等重点问题进行了详细的讨论和分析.     

基于神经网络模型的襟翼主动控制旋翼减振分析

基于径向基函数(Radial basis function,RBF)神经网络构建了一种带后缘襟翼主动控制(Active controlled flap,ACF)的旋翼振动载荷计算模型。采用正交试验方法确立RBF网络训练样本的输入,在CAMRAD II中计算前飞状态下与训练样本对应的旋翼桨毂六力素,并将主通过频率下的分量作为样本输出,对RBF网络进行离线训练。在此基础上采用多周控制器对被控模型进行振动载荷主动控制。随后以2桨叶4m直径ACF旋翼为例,构建了其桨毂减振分析方法,并对桨毂动载荷各分量的减振效果进行了分析。研究表明,采用正交样本训练的RBF网络能够精确映射襟翼偏角与桨毂振动载荷的非线性关系,施加多周控制后,桨毂垂向振动载荷降低接近50%,其他方向的振动载荷也有不同程度的降低。     

来流马赫数对引射火箭引射量的影响研究

研究引射火箭引射量随来流马赫数的变化关系,对引射量由火箭引射主导向冲压主导之间转换点的选取以及一次火箭的质量管理具有重要意义.采用数值分析和实验研究,探索了引射火箭引射量随来流马赫教的变化关系.结果表明,针对所采用的引射火箭发动机构型,引射量随来流马赫数变化的拐点约为Ma=1.3～1.5,当来流马赫数Ma<1.3时,引射量由火箭引射主导,随来流马赫数的增加,引射量变化较缓慢;当来流马赫数Ma>1.5时,引射量由冲压主导,随来流马赫教的增加,引射量迅速增加.     

斜激波极值规律的边界层影响

采用边界层理论与斜激波/膨胀波精确算法，建立一种结合Eckert参考温度法和Illingworth-Stewartson变换法优势的边界层权重算法，用于研究超声速黏性楔面边界层位移厚度对斜激波极值规律的影响。分别应用层流Navier-Stokes方程和湍流Navier-Stokes方程的CFD解算器对边界层新模型进行了算例精度评估。在来流马赫数为1.2~2.4和楔面角为3°~20°的范围内，压强比的相对误差小于0.1%。计入层流与湍流边界层影响的理论模型研究表明，边界层影响使得最优马赫数增加；对于层流边界层，最优马赫数增量约为0.001 5~0.003 3；对于湍流边界层，最优马赫数增量约为0.002 8~0.006 1。     

Optimum parameter matching obtained by experiments for coring drilling into lunar simulant

This paper performs a series of ground experiments (on the Earth) to obtain optimum parameter matching for a future core drill on the Moon. Three common stages, I, II, III, are recognized with respect to the cut per revolution (CPR), which is defined as the ratio between the feeding speed and the rotating speed. The optimum matching between the feeding speed and the rotating speed for drills locates at the boundary position between Stage II and Stage III, where the coring rate saturates and the weight on the bit and the driving torque are still low. Further data analysis of the ground experiments reveals that the optimum matching signifies a proportional relation between the maximum conveying rate (MCR) by the groove of the auger and its rotating speed. The kinetic analysis in an ideal condition without gravity, the friction from the auger groove and the pressure at the bit confirm a similar proportion. The correlation between the proportions needs further study to determine whether the optimum matching obtained on the ground can be directly applied to future drills on the Moon.     

浅议我国个人所得税实施中存在的问题及解决对策

个人所得税在调节个人收入、增加财政收入、维护国家权益等方面发挥了积极作用,但是随着我国经济的发展,在实施个人所得税中也逐渐暴露出一些问题.本文针对这些问题,进行了深刻的分析,并提出了解决的对策.     

水平表面气流剪切作用下的水膜厚度

飞机结冰表面上的液态水受气流吹拂作用会发生向后溢流,从而影响结冰区域范围及防冰系统设计;为了获得水膜流动规律,对水平平板表面上气流剪切驱动的水膜流动进行了实验测量和建模分析。通过水膜流动风洞试验台产生高速气流驱动水膜的流动,使用色散共焦位移计测量同一位置的水膜在不同时刻的厚度变化,结果表明气-液界面由底层薄水膜和多种尺度的波动组成,具有变化速度快随机性强的特点。通过水膜厚度随气流速度及水膜雷诺数的变化规律,发现平均水膜厚度与两者均呈现出单调非线性的依赖关系。基于薄水膜流动理论和平均水膜厚度实验结果,提出了高速气流剪切作用下的气-液波动界面剪切因子计算式,适用于风速17.8~52.2m/s,水膜雷诺数26~128之间的平板水膜流动计算。