某航机燃烧室煤油改柴油燃烧特性研究

为了给某型航空发动机改为地面用柴油型燃气轮机的设计提供重要的技术支持,本文借助数值计算的方法,采用FLUENT稳态压力求解器、P1辐射模型和涡耗散破碎(EDU)燃烧模型对某航空发动机燃烧室在巡航工况和最大工况下煤油与柴油两种燃料的燃烧特性进行了计算及对比研究。得到了该燃烧室使用航空煤油(RP-3)和0号柴油的热态流场、空气流量分配、温度场、出口温度分布、污染物排放及头部燃油蒸发量。研究结果表明：当该燃烧室的燃料由航空煤油改为0号柴油后,燃烧室的热态温度场分布基本一致,流量分配最大差异在0.45%之内；燃烧效率降低约4.3%和NO、Soot排放量相当；出口温度分布和总压损失差异分别在1%和4.1%之内。     

Investigation on low total temperature combustion characteristics of kerosene-fueled supersonic combustor

In this paper, the combustion characteristics of kerosene-fueled supersonic combustor under the conditions of Mach number 2.0, the total temperature at 700 K and the total pressure at 520 k Pa(simulated flight Mach number at 3.5) were studied by using the flame stabilizing method of cavity and strut from three aspects such as blockage ratios, kerosene equivalence ratios, location and quantity of injection holes. The results showed that:(A) The combustor with the strut realized the independent an...     

模型燃烧室中值班火焰稳定器的燃烧不稳定性研究

针对值班火焰的燃烧不稳定性问题，通过试验得到了不同当量比工况下的火焰结构、压力脉动信号和热释放脉动信号。对脉动信号进行傅立叶分析，获得了脉动信号的频率和振幅。结果表明，随着当量比增加，火焰形态发生变化，燃烧室内发生了164Hz三阶模态向109Hz二阶模态的转换。对火焰平均结构、火焰瞬态结构和火焰正交分解（POD）结果进行分析后发现，漩涡脱落频率和燃烧室某一阶声学模态耦合是维持燃烧不稳定性的机理，耦合的强弱和漩涡脱落的尺度大小决定了热声振荡的振幅大小，火焰形态的变化导致热释放中心位置的变化是引起模态转换的机理。     

船用大功率柴油机瞬态工况油气响应及燃烧特性研究

针对船用大功率柴油机瞬态性能提升的需求，开展了增压中冷船用大功率柴油机瞬态工况动态响应及燃烧特性实验研究。研究表明，涡轮增压器惯性导致的进气滞后是柴油机瞬态工况下性能恶化的主要原因；突加载工况下，进气量响应滞后供油量响应4~5个工作循环，且进气量响应速度随初始负荷增加而增加，指示平均有效压力（Indicated Mean Effective Pressure，IMEP）等燃烧特征参数加载过程中响应速度较快，波动较小；缸内燃烧过程恶化，燃烧重心和燃烧终点较同负荷下稳态工况值均推迟。     

Similarity phenomena of lean swirling flames at different bulk velocities with acoustic disturbances

In this study, flame responses to acoustic disturbances with different frequencies and amplitudes were experimentally investigated in a lean premixed swirl-stabilized combustor operating at different bulk velocities. The total heat release rate fluctuations and spatial CH* chemiluminescence distributions were captured using a photomultiplier tube and high-speed camera, respectively. The results indicate that the heat release rate exhibits a relatively drastic oscillation and high-order harmonics for low-frequency disturbances. When the bulk velocity and forcing frequency were doubled simultaneously, similar flame structures were observed in the CH* chemiluminescence distributions. As the bulk velocity increases, the gain of the Flame Describing Function (FDF) extends toward the higher frequencies, and the delay time of the flame response decreases. The similarity among FDFs at different bulk velocities was effectively captured by introducing a non-dimensional parameter, defined as the ratio of the flame response delay to the forcing time scale, to replace the dimensional forcing frequency. Furthermore, the availability of the newly defined non-dimensional parameter was verified for flames with different swirl numbers, as this played an important role in determining the flame structures and associated unsteady heat release rate.     

Effect of mixing section configurations on combustion efflciency of Mg-CO2 Martian ramjet

Experiments were conducted to determine the effects of the mixing section configurations on the Mg-CO₂ Martian ramjet combustion efficiency. It was carried out at a mainstream mass flow rate of 110 g/s and a temperature of 810 K. The chamber pressure was measured under different configurations and Oxidizer to Fuel(O/F) ratios. Results showed that the engine achieved self-sustaining combustion and worked stably during experiments. The pre-combustion chamber is needed to increase the co...     

Effect of baffle injectors on the first-order tangential acoustic mode in a cylindrical combustor

Combustion instability is a very important issue in the development of the propulsion systems used in aerospace. It is very important to associate the high frequency combustion instabilities with the acoustic characteristics of the combustion chamber. In this paper, the effects of various baffle injectors which were installed on the injector faceplate on the first-order tangential acoustic mode were investigated theoretically and experimentally. The effects of the gap between adjacent injectors on the first-order tangential acoustic mode in a cylindrical chamber were considered. The acoustic admittance of the injectors was derived. The results showed that the amplitude and frequency of the first-order tangential acoustic mode increase with the increase in the gap between adjacent injectors, but decrease with the increase in the number and height of the baffles. The baffle injectors have a greater influence on the amplitude and frequency of the first-order tangential acoustic mode than the baffle blades.     

Effect of injection scheme on asymmetric phenomenon in rectangular and circular scramjets

The asymmetric separation has a crucial effect on the performance of the scramjet. In this study, the asymmetric separation and combustion in both rectangular and circular scramjets are investigated numerically, and the effect of injection scheme is analyzed. The characteristics of the flow field are analyzed based on sufficient code verification. In the rectangular scramjet, the separation tends to occur in the corner due to the corner boundary-layer effect. The separation is asymmetric and only two corners have serious separation. The fuel penetration depth in the separation zone increases and the combustion is intensified. When the injection scheme is uniform, both the combustion and separation become weak. In the circular scramjet, the separation and combustion are basically axisymmetric in the scramjet with one-row injection scheme. The asymmetric combustion becomes obvious in cases with multi-row injection scheme. When the injection orifices distribute intensively on the top and bottom sides, the strongest and weakest separations occur near these two sides respectively. When the distribution of orifices becomes uniform, the direction of separation cannot be predicted. For multi-row cases, the nonuniform injection scheme could result in violent combustion and asymmetric flow structures compared with the uniform injection scheme.     

进气道出口截面形式对补燃室掺混性能的影响研究

为研究进气道出口截面形式对补燃室掺混气动特性和燃烧性能的影响，本文对双下侧布局形式的固冲发动机内流场进行数值模拟，对比分析了补燃室相同压比下两种不同进气道出口截面形式在不考虑燃气的混合和反应时掺混段的气动特性和考虑燃气反应时补燃室的燃烧性能。结果表明：两股空气掺混过程中，研究的两种进气道出口截面方案的整体总压损失大致相同，但进气道圆形出口截面的掺混段内流线表现为不稳定的螺旋点形态，相比于方形出口截面的掺混段，其使气流掺混更剧烈，短距离内掺混已经很均匀，且旋流强度小；在考虑燃烧时，进气道圆形出口截面对应的补燃室出口总压恢复系数比方形截面的高约2%，方形进气道出口截面的补燃室出口截面总燃烧效率为95.58%，而圆形截面的达到99.86%。     

Mixing and combustion characteristics in a scramjet combustor with different distances between cavity and backward-facing step

The mixing and combustion characteristics in a cavity flameholding combustor under inlet Mach number 2.92 are numerically investigated with ethylene injection. Dimensionless distance is defined as the ratio of the actual distance to the height of the combustor entrance. The cavity shear-layer mode, the lifted cavity shear-layer mode, and jet wake mode with upstream separation are observed respectively with dimensionless distance equals to 1.5, 4.5, and 7.5. In both non-reacting and reacting flow...