Feasibility evaluation of failure models for predicting forming limit of metal foils

Forming limit of metal foil is an important index to evaluate its formability, and is of considerable significance to improve the quality of products. The ductile fracture (DF) behavior in microscale plastic deformation is remarkably affected by the geometry and grain size. To explore the size-dependent forming limit curve (FLC), the Holmberg and Marciniak tests of SUS304 foils with the thicknesses of less than 0.1 mm and diverse grain sizes were performed. In addition, the validity and feasibility of three types of existing failure models including Swift/Hill, Marciniak-Kuczynski (M-K) and DF criteria for predicting the micro-scaled FLCs were discussed. It is found that the Swift/Hill model possesses the worst accuracy with predicting deviation above 50%. Four classical DF criteria including Freudenthal, Ayada, Brozzo and Oh show great difference, and Oh model considering plastic anisotropy presents the best precision. The predicted deviation of M-K model is aggravated with increasing grain size and decreasing foil thickness, which is attributed to the intensified free surface roughening and transformation of fracture mechanism with miniaturization. This research thus provides a deeper understanding and valuable reference for the widespread application of FLC in microforming.     

Investigation on surface roughness,residual stress and fatigue property of milling in-situ TiB2/7050Al metal matrix composites

For higher efficiency and precision manufacturing, more and more attentions are focused on the surface roughness and residual stress of machined parts to obtain a good fatigue life. At present, the in-situ TiB₂/7050Al metal matrix composites are widely researched due to its attractive properties such as low density, good wear resistance and improved strength. It is of great significance to investigate the machined surface roughness, residual stress and fatigue life for higher efficiency and precision manufacturing of this new kind material. In this study, the surface roughness including two-dimensional and three-dimensional roughness, residual stress and fatigue life of milling in-situ TiB₂/7050Al metal matrix composites were analyzed. It was found from comparative investigation that the three-dimensional surface roughness would be more appropriate to represent the machined surface profile of milling particle reinforced metal matrix composites. The cutting temperature played a great role on the residual stress. However, the effect of increasing cutting force could slow down the transformation from compressive stress to tensile stress under 270 °C. An exponential relationship between three-dimensional roughness and fatigue life was established and the main fracture mechanism was brittle fracture with observation of obvious shellfish veins, river pattern veins and wave shaped veins in fracture surface.     

涡轮叶片尾缘复合通道的换热

采用热色液晶测温法,测量了涡轮叶片尾缘带隔板的复合通道的温度场,分析了射流冲击强化扰流柱通道内换热的机理,讨论了两通道间隔板的不同开孔结构对换热的影响.从工程应用的角度出发提出了几个换热评价指标,对不同开孔结构的隔板进行了换热评价.结果表明:冷气由第1通道进入,通过隔板上的孔不断由径向流动变为弦向流动后,对第2通道的扰流柱区形成冲击,最后由劈缝排出,提高了尾缘的换热;开孔均匀的隔板换热效果相对较好.     

微型定容多次燃油喷射系统高速响应特性仿真

针对小排量发动机转速范围大、工作循环喷油量小的特点,提出了一种微型定容多次燃油喷射系统结构,建立了系统电、磁、液、机耦合模型,仿真计算了从输入电压到喷射输出的动态响应特性,分析了影响系统高速特性的关键因素.结果表明:该喷射系统响应频率可达到1000Hz,响应时间可以满足小排量发动机最高转速要求,具备工程可实现性.      

涡轮叶片尾缘复合通道的流动与换热

实验研究了涡轮叶片尾缘带纵向隔板内冷通道的流动与换热特性.采用相变加热的方法为实验提供了等壁温边界条件,模型实验件采用了扰流柱和微小通道结构,并且分别与直隔板和波形隔板进行组合实验,以期望得到综合换热效果最优的组合.为了获得通道的局部换热信息,实验件的一侧外壁面被细分成了10个集水区域分别进行研究.结果表明:当Re在10 000~60 000之间时,综合换热效果最差的是直隔板加光通道的组合结构,综合换热效果最佳的是波形隔板加微小通道的组合结构.     

金属增材制造技术应用于军用飞机维修保障浅析

金属增材制造技术的发展为军用飞机维修保障提供了一条数字化、定制化、高性能、短周期的技术新途径,可提升军用飞机维修保障的技术水平和能力。本文综述了军用飞机维修保障的国内外现状,指出了金属增材制造技术的应用优势,介绍了军用飞机零件的典型损伤形式、不同增材制造工艺的适用性及修复工艺选取方案,分析了所涉及的逆向建模、结构优化、智能机器人等关键技术,详述了目前存在的技术成熟度与可靠性不高、修复原则不明确、标准规范不统一等主要问题及解决措施,指出了增材制造技术在军用飞机维修保障领域未来的发展方向和趋势,并给出了具体的应用建议。     

金属增材制造数据处理与工艺规划研究综述

金属增材制造数据处理与工艺规划是金属增材制造软件系统的核心,涵盖了金属支撑结构设计、模型切片以及路径规划等内容,决定着最终金属零部件的产品性能。从金属增材制造模型前处理出发,较为全面地概述了与之相关的多类型支撑设计和新型支撑优化等数据处理内容,针对金属增材制造数据处理中模型切片这一关键环节,分别从平面切片、自适应切片和曲面切片等方面进行了研究进展综述,同时对金属增材制造工艺中的路径规划研究进展进行了概述,最后对其发展趋势做了初步展望。     

复合材料与金属胶接结构的次弯曲效应研究

复合材料与金属胶接单搭接的次弯曲效应引起的剥离应力,会大大降低接头的强度。采用有限元方法分析复合材料铺向角、铺层顺序及斜削对次弯曲的影响,并进一步研究分析次弯曲和胶层剥离应力、板的弯曲刚度之间的关系。结果表明：次弯曲影响剥离应力的大小;弯曲刚度越大,次弯曲越小;斜削有助于减小次弯曲。     

钛合金热成形和超塑成形金属平台材料选型和制备

介绍了钛合金热成形和超塑成形用金属平台的材料选型和制备工艺研究情况,研究认为,选择高温合金替代目前国外采用的耐热钢材料优势非常明显;钢铁研究总院自主开发的热成形金属平台制备工艺比国外相关技术更加先进,制备的K403高温合金热成形平台服役表现良好,具备了生产钦合金热成形和超塑成形金属平台的能力.     

带颗粒型金属橡胶夹层阻尼结构的振动响应研究

针对冲压发动机中高温板壳结构的振动抑制需求,提出新型颗粒金属橡胶夹层阻尼结构,基于模态应变能法建立了其动力学理论模型和数值求解方法。与试验结果对比表明,共振幅值的相对误差不大于20%。进一步采用理论分析与试验相结合的手段,论述了颗粒型金属橡胶夹层阻尼的有效性,可有效降低振动响应3~8倍;随着填充密度的增加,减振效果增加;对于一弯和二弯振动,下部填充减振效果最好,而在下部填充,振动响应会被放大;依据数值计算获得的应变能分布结果,进行夹层设计可达到良好的减振效果。