连续推力机动轨道优化设计的贝塞尔曲线法

提出一种基于贝塞尔曲线的平面机动轨道设计方法。该方法将贝塞尔曲线方程与轨道形状方程相结合，利用得到的复合函数作为轨道方程来对机动轨道进行数学描述；通过约束条件获得可行的机动轨道族，由控制点设计给出具体的优化变量，将累积速度增量作为优化指标函数；并利用优化算法完成参数优化，从而得到最优机动轨道。最后针对设计的机动轨道推力峰值较大的问题，进一步提出了分段贝塞尔曲线法，在降低推力峰值的同时，可进一步降低燃料消耗，并在平面机动转移轨道设计的基础上，通过梯度下降对自由控制点进行修正，解决了考虑时间约束的平面轨道交会问题。     

A strategic “viewfinder” for SETI research

One of the most important reasons why unsuccessful results have been obtained so far by the SETI Project is due to the fact that no sure targets to aim at have been available up-to the present state of research. All-sky surveys, even if very accurate and complete, might result to be time-consuming. SETI needs at least one effective “viewfinder” in order that a true targeted research is carried out with a possible success. The best foundation to get this can be identified with the search for the evidence of extraterrestrial astro-engineering activity in form of the Dyson spheres predicted by theory. The existence of such stellar objects can be ascertained by finding the evidence of two main signatures in stars of solar spectral type: infrared excess and anomalous light curves due to transiting artificial objects. These are probably the most powerful viewfinders in order to allow SETI techniques for intelligent signal search to be aimed at more appropriate targets. This paper is not intended to be a research paper but rather a review paper whose goal is not to present calculations and/or operational research but rather to be a research proposal for a more focused research in SETI just using Dyson Spheres as crucial markers.     

磁悬浮框架飞轮磁轴承技术研究与发展现状

对磁悬浮框架飞轮(MSGFW)和高精度磁轴承研究现状及其未来发展进行了详细阐述。根据转子悬浮力类型，将磁悬浮框架飞轮分为磁阻力构型、洛伦兹力构型和混合力构型，并结合三种构型论述了国内外框架飞轮的发展过程。在此基础上，对球面磁阻力磁轴承和洛伦兹力磁轴承进行了详细介绍，并结合磁路图分析其工作原理，比较了同类磁轴承的优劣。展望了磁悬浮框架飞轮与高精度磁轴承的未来发展方向，指出高动态响应检控共位平动球面磁阻力磁轴承，标准磁悬浮动量球和磁悬浮控制敏感球是磁悬浮框架飞轮的研究重点。     

曲线物面边界条件在DGM中的应用研究

基于二维非结构网格,采用高精度间断Galerkin有限元方法数值求解定常Euler方程。为了有效克服传统的反射物面边界条件在物面处易于生成伪熵降低计算精度的缺陷,提出一种曲线物面边界条件,从而实现对物理模型而不是数值模型进行数值模拟。对经典圆柱亚音速无粘绕流进行数值模拟,结果表明:采用曲线物面边界条件之后,流场解的精度得到很好的提高;此外,在非常稀疏的网格上,通过提高基函数的阶次仍可以得到高精度的数值解。     

舰载机增升装置对薄翼型升力系数的影响研究

描述了增升装置在提高舰载机薄翼型升力系数方面的作用,观察到大偏角前缘襟翼小迎角时对翼型升力曲线的影响,并通过与试验现象对比,初步探讨了非线性作用形成的可能机理。利用数值模拟方法,通过有限元计算软件对相同流场中多种增升装置的升力系数进行了模拟与比较,从而达到合理设计舰载战机翼型的目的。CFD计算结果表明,所设计的二维多段翼型有良好的气动特性,升力系数得到提高,具有较好的增升效果。     

液压减震器动力特性的影响因素研究

介绍了摩托车液压减震器的结构及原理，建立了其动力特性的理论模型。通过数字仿真计算研究了液压油的容性、感性等对减震器动力特性的影响情况，得出了两者影响刚好相反的结论，并与实际测量结果对比，验证了模型的正确性。这对减震器性能优化及结构改进具有指导价值，为建立基于几何尺寸参数的减震器动力特性模型奠定了基础。     

碳硼复合渗研究及其应用

本文研究了２０钢和４５钢的碳硼复合渗渗层组织及耐磨性能。结果表明：复合渗可得到较强支撑作用的过渡层，从而使渗硼层耐磨性提高。饲料粉碎机锤片采用复合渗工艺处理后试用效果良好。     

Tear Resistance of Orthogonal Kevlar-PWF-reinforced TPU Film

This work seeks to investigate the notch sensitivity and fracture behaviour of orthogonal Kevlar-plain woven fabric (PWF)-reinforced thermoplastic polyurethanes (TPU) film applied to high altitude balloon. Four types of specimens are implemented to measure notched strength and fracture toughness by conducting static tension and tear tests on an MTS system respectively. The damage and failure mechanisms are discussed and the results for notched strength and tear resistance are evaluated and compared with each other. From the experiments, it is found that the notch sensitivity of the film increases with the increase in the size of the hole, but the notch sensitivity and the stress concentration of the notch are insignificant and there is a decrease of only about 4%-10% in tensile strength for the notched specimens with different hole sizes in diameter compared with the unnotched specimen. In contrast, the tear resistance containing a central slit with only 1 mm length is about half of tensile strength of the unnotched film, which implies that the tear resistance exists an significant notch sensitivity. The results of this study provide an insight into notch sensitivity and fracture behaviour of the Kevlar-PWF-reinforced TPU film and constitute a fundamental basis for the design of high altitude balloon.     

跨声速风洞斜孔壁非线性流动试验

为分析跨声速风洞斜孔壁近壁区域的流动特性，评估气流偏角-压力系数的非线性关联，在0.6 m跨超声速风洞中开展了基于七孔探针的流动特性测量试验。通过气流偏角和压力系数分布分析了斜孔壁流动的差阻特性，以及马赫数、模型升力对斜孔壁流动的影响，最后基于试验结果发展了计算斜孔壁特性参数的微分法，并与经验方法结果进行对比。结果表明，斜孔壁流动呈现出明显的差阻性和非线性，在负压差范围内，近壁流动仍以出流为主；高亚声速时，空风洞模型区孔壁流动特性趋于实壁；安装模型后，随着升力的增大，升力面对应的孔壁区域流动向入流发展，孔壁流动特性趋于开口边界。     

关于多项式系数二阶线性微分方程的可积性问题

主要探讨了实域上当ｇ（ｘ），ｈ（ｘ）是多基式，二阶变系数线性微分方程ｙ″＋ｇ（ｘ）ｙ‘＋ｈ（ｘ）ｙ＝０的可积性问题，沿袭了文」１「中算子矩阵理论的思想，得到了该方程要积的充分必要条件，且给出可积时的通解公式，并举例指出了文中「５，６」中收集的许多可积的二阶线性微分方程，其中相应的多项式系数的部分均是本文的特例。