基于新型降阶模型的网格加筋圆柱壳频率分析

针对网格加筋圆柱壳频率分析计算量大的问题,提出一种基于多项式及梁单元形函数的模型降阶方法,即运用多项式及梁单元形函数将复杂结构有限元的节点位移转化为主节点位移,实现模型降阶。并通过控制多项式阶数及梁单元个数来调整降阶模型的分析精度,而降阶模型的计算效率较精细模型有显著提高。以网格加筋圆柱壳为例,对比本文提出的模型降阶方法与3-D实体模型及其他模型降阶方法的频率分析结果,结果表明,提出的模型降阶方法不仅能捕捉到结构的整体模态,还能反映出结构部分局部模态,适用范围广,能够为工程结构设计提供简单有效的计算模型。     

一种基于观测站数目最小化的TDOA/FDOA无源定位算法

在三维（3D）运动目标无源定位系统中，无模糊定位最少需要4个观测站。而传统的两步加权最小二乘（TSWLS）及其改进的闭式算法至少需要5个观测站进行求解，当减少一个观测站时，这些闭式算法往往无法提供可靠解。针对这一问题，提出一种最小化观测站数目的到达时间差（TDOA）与到达频率差（FDOA）定位算法。该算法是一种闭式解法并且能够在三维场景下仅使用4个观测站进行定位。该算法分为两步：第1步分离传统的TSWLS算法中未知参数空间，建立了一组新的等式，并且利用加权最小二乘（WLS）算法得到目标位置与速度的初始值；第2步利用泰勒级数展开算法将中间变量线性化，对目标位置和速度初始值进一步校正。理论分析证明了在适当的噪声水平下该算法能够达到克拉美罗界（CRLB）。此外，计算机仿真表明仅使用4个观测站时，该算法对于近场以及远场目标参数的估计精度在测量噪声较小时可以实现CRLB；并且还表明使用5个观测站估计时，该算法比TSWLS及其改进算法能更好地适应大的测量噪声。     

Early analysis of precise orbit and clock offset determination for the satellites of the global BeiDou-3 system

Eight new-generation BeiDou satellites (BeiDou-3) have been launched into Medium Earth Orbit (MEO), allowing for global coverage since March 2018, and they are equipped with new hydrogen atomic clocks and updated rubidium clocks. Firstly, we analyzed the signals for the carrier-to-noise-density ratio (C/N0) and pseudorange multipath (MP) by using international GNSS (Global Navigation Satellite System) Monitoring and Assessment System (iGMAS) station data, and found that B1C has a lower C/N0, and B2a has the same level of C/N0 as the B1I and B3I signals. For pseudorange multipath, compared with the BeiDou-2 satellites, the obvious systematic variation of MP scatters related to the elevation angle is greatly improved for the BeiDou-3 and BeiDou-3e satellites signals. For the signals of the BeiDou-3 satellites, the order of the Root Mean Square (RMS) values of multipath and noise is B3I?<?B1I?<?B2a?<?B1C. Then, the comparison of the precise orbit determination and clock offset determination for the BeiDou-2, BeiDou-3, and BeiDou-3 experimental (BeiDou-3e) satellites was done by using 10 stations from iGMAS. The 3D precision of the 24?h orbit overlap is 24.55, 25.61, and 23.35?cm for the BeiDou-3, BeiDou-3e, and BeiDou-2 satellites, respectively. BeiDou-3 satellite has a comparable precision to that of the BeiDou-2 satellite. For the precision of clock offset estimation, the Standard Deviation (STD) of the BeiDou-3 MEO satellite is 0.350?ns, which is an improvement of 0.042?ns over that of the BeiDou-2 MEO satellite. The stabilities of the BeiDou-3 and BeiDou-3e onboard clocks are better than those of BeiDou-2 by factors of 2.84 and 1.61 at an averaging time of 1000 and 10,000?s, respectively.     

Sunspot activity and cosmic ray modulation at 1 a.u. for 1900–2013

The descent of sunspot cycle 23 to an unprecedented minimum of long duration in 2006–2009 led to a prolonged galactic cosmic ray (GCR) recovery to the highest level observed in the instrumental era for a variety of energetic charged particle species on Earth, over a wide range of rigidities. The remarkable GCR increase measured by several ground-based, balloon-borne, and detectors on a satellite is described and discussed. It is accompanied by a decrease in solar wind velocity and interplanetary magnetic field at 1 a.u., reaching the lowest values since measurements of the solar wind began in October 1963; the solar polar field strength (μT) measured at the Wilcox Solar Observatory (WSO) is also significantly reduced compared to prior cycles since the start of the program in 1976, the polar field in the northern hemisphere reversed in June 2012 and again in February 2014, that in the southern hemisphere reversed in July 2013. If updates of WSO data confirm the second reversal in northern solar hemisphere, it would pose a serious challenge to the Dynamo Theory. The long-term change in solar behavior may have begun in 1992, perhaps earlier. The physical underpinnings of these solar changes need to be understood and their effect on GCR modulation processes clarified. The study discusses the recent phenomena in the context of GCR modulation since 1900. These happenings affected our empirical predictions for the key parameters for the next two sunspot cycles (they may be progressively less active than sunspot cycle 24) but it enhanced support for our prediction that solar activity is descending into a Dalton-like grand minimum in the middle of the twentyfirst century, reducing the frequency of the coronal mass ejections; they determine the space weather affecting the quality of life on Earth, radiation dose for hardware and human activities in space as well as the frequency of large Forbush decreases at 1 a.u.     

基于ANSYS Workbench的行星滚柱丝杠动态特性分析

通过Pro/Engineer建立行星滚柱丝杠三维模型，基于ANSYS Workbench有限元分析技术进行模态与谐响应分析，得到前六阶固有频率与各阶模态振型，确定共振频率，掌握对应频率下的位移峰值响应，并研究螺母处于不同工作位置时对固有频率的影响，为基于行星滚柱丝杠传动的舵系统抗振设计提供数据支撑。     

无源滤波器频率漂移的一种迭代算法

文章介绍了无源滤波器在试验过程中产生的典型幅频特性漂移曲线，并针对这些典型曲线提出了基于均方误差最小原则和牛顿迭代的频率漂移算法。     

电离层色散对DS/FH-BPSK信号解调性能影响

相位连续的DS/FH(Direct Sequence/Frequency Hopping,直接序列/跳频)扩频信号的扩频带宽比直扩信号更宽,在电离层的非线性相位以及跳频频点变化这两者的共同作用下,该信号的BPSK(Binary Phase Shift Keying,二相相移键控)解调性能明显恶化。依据随机变量概率分布的数学规律,推导得到了在背景电离层色散条件和跳频频点均匀分布前提下,某种DS/FH卫星测控信号的引导信号和长周期信号BPSK误码率的变化规律,并在特定信号参数条件下进行了误码率仿真。     

无人机高速DS/FH混合扩频通信系统关键模块设计

针对UAV(Unmanned Aerial Vehicle,无人机)测控链路高抗干扰需求,给出了实现跳频速率20 000次/s的扩跳混合无人机测控数据链系统实现方案.系统采用跳频频率并行捕获模式.跳频源设计采用直接频率合成、DDS(Direct Digital Synthesis,直接数字频率合成)和PLL (Phase-Locked Loop,锁相环)相结合的混合频率合成技术.利用相位响应滤波器,通过正交调制技术完成MSK(Minimum Shift Keying,最小频移键控)、GMSK (GaussianMinimum Shift Keying,高斯最小频移键控)调制.通过推导得出2 bit差分解调输出与载波频率选择有关,且为四分之数据率的整数倍关系.然后通过实例分析给出了跳频频率间隔选取方法,即跳频间隔应当将临近跳频的主瓣分开,同时跳频载波频率应当设在其他跳频频谱的零点处.最后总结了高速扩跳频系统参数设计一般步骤.     

流向强迫作用下的液体初始雾化机制及动力学特征

使用Volume of fluid (VOF)方法和基于树形数据结构的自适应算法来研究射流雾化的破碎过程以及扰动对射流破碎机理产生的影响。在无扰动情况下,液体射流的头部、液丝和液滴随着射流时间的发展不断发生演变。射流头部先呈现蘑菇状外形,随后液丝生成,并慢慢转变成网兜状,直至断裂形成小液滴。在周期性流向强迫的作用下,射流液柱的表面会形成周期波,其液丝破裂形成液滴的时机与稳定射流情形相比会有所提前,射流形成的头部更趋于扁平,最终生成的液滴数量更多。低中频阶段,随着扰动频率的增大,射流未扰动液柱长度(L)逐渐缩短,液滴直径的概率密度分布(PDF)趋于尖锐,液滴平均直径(SMD)增大。在高频阶段,随着扰动频率的增大,L会随之增大,液滴直径的PDF分布变得平缓,SMD会减小。     

帆板控制系统设计

该帆板控制系统采用塑料薄膜电位器作为传感器检测角度信号,检测到的角度信号经信号处理电路送12位的串行接口A/D转换器ADS7818进行数字化转换,转化结果由Cortex-M3处理器LM3S615进行处理产生PWM控制信号,该控制信号经功率VMOS驱动电路实现轴流电扇的速度调节,从而实现帆板角度定位闭环控制。通过按键可以实现帆板角度的设定及运行控制,设置六位LED数码管显示实现角度及其它运行状态的显示。经过实际测试该系统完全达到了设计要求的各项指标要求。