SiO32-浓度对KMnO4/FeSO4工艺除磷过程的影响

考察了天然水体中常见的SiO_3~(2-)对KMnO_4/FeSO_4工艺混凝除磷的影响。SiO_3~(2-)存在时KMnO_4/FeSO_4工艺混凝除磷的效能随着溶液pH的升高呈现先增加后降低的趋势。SiO_3~(2-)浓度为1.0 mmol/L,溶液pH值为4～6时,SiO_3~(2-)可促进KMnO_4/FeSO_4工艺除磷的效能,KMnO_4/FeSO_4工艺对磷的去除效果分别增加了6.0%,9.9%和6.3%;溶液pH值为7～9时,SiO_3~(2-)可显著抑制KMnO_4/FeSO_4工艺除磷的效能,KMnO_4/FeSO_4工艺对磷的去除效果分别降低了14.76%,32.6%和17.3%。KMnO_4/FeSO_4工艺形成的絮体颗粒物表面ζ电位显著降低,溶液中残余铁的量明显提高。另外,水中SiO_3~(2-)对KMnO_4/FeSO_4工艺形成的絮体颗粒物的组成和表面特征均有一定影响。该研究为KMnO_4/FeSO_4工艺混凝除磷技术的推广提供了必要的理论基础。     

Energy principle and material removal sequence optimization method in machining of aircraft monolithic parts

In the machining process of aircraft monolithic parts, the initial residual stress redistribution and structural stiffness evolution often lead to unexpected distortions. On the other hand, the stress redistribution and stiffness reduction during the machining process depend on the material removal sequence. The essence of the stress redistribution is releasing the initial elastic strain energy. In the present study, the influence of the material removal sequence on the energy release is studied. Moreover, a novel optimization method is proposed for the material removal sequence. In order to evaluate the performance of the proposed method, the mechanism of the machining distortion is firstly analyzed based on the energy principle. Then a calculative model for the machining distortion of long beam parts is established accordingly. Moreover, an energy parameter related to the bending distortion and the procedure of the material removal sequence optimization is defined. Finally, the bending distortion analysis and material removal sequence optimization are performed on a long beam with a Z-shaped cross-section. Furthermore, simulation and experiments are carried out. The obtained results indicate that the optimized sequence results in a low distortion fluctuation and decreases the bending distortion.     

Sliding mode control design for oblique wing aircraft in wing skewing process

When the wing of Oblique Wing Aircraft (OWA) is skewed, the center of gravity, inertia and aerodynamic characteristics of the aircraft all significantly change, causing an undesirable flight dynamic response, affecting the flying qualities, and even endangering the flight safety. In this study, the dynamic response of an OWA in the wing skewing process is simulated, showing that the three-axis movements of the OWA are highly coupled and present nonlinear characteristics during the wing skewing. As the roll control efficiency of the aileron decreases due to the shortened control arm in an oblique configuration, the all-moving horizontal tail is used for additional roll and the control allocation is performed based on minimum control energy. Given the properties of pitch-roll-yaw coupling and control input and state coupling, and the difficulty of establishing an accurate aerodynamic model in the wing skewing process due to unsteady aerodynamic force, a multi-loop sliding mode controller is formulated by the time-scale separation method. The closed-loop simulation results show that the asymmetric aerodynamics can be balanced and that the velocity and altitude of the aircraft maintain stable, which means that a smooth transition is obtained during the OWA’s wing skewing.     

正弦压力信号幅值测量无差算法研究

正弦压力校准常用比较法，通过比较标准压力传感器与被校压力传感器在同一正弦压力源中的响应完成被校传感器的幅值校准。对正弦压力信号幅值的测量算法进行了研究，提出了一种控制采样频率为标准激励信号频率整数倍的算法，可实现幅值的无差运算，理论推导和仿真实验表明，该算法能有效提高单频校准的准确度。     

压电阻抗技术监测固体推进剂老化研究

为了进一步研究表面粘贴式的主动传感技术——压电阻抗技术(EMI, Electro-Mechanical Impedance)监测固体推进剂的老化,构建了基于线粘弹杆结构的一维机电耦合模型,根据粘弹性波的理论与边界条件进行分析,建立一种线粘弹结构动态模量与其机械阻抗的表征关系,并对构建的机电耦合阻抗模型进行了数值计算及试验验证。针对HTPB固体推进剂开展高温热加速老化试验及压电主动激励试验,根据监测所得导纳频谱并通过提取结构机械阻抗进行分析,结果表明:压电陶瓷片与推进剂结构在高频机电耦合运动时(300kHz,280kHz)有明显的共振现象,结构固有频率高于机电耦合共振频率,并且在200kHz～400kHz频段与700kHz～900kHz频段内,结构机械阻抗频谱峰值会因固体推进剂的热老化时间增长而降低,且与热老化时间之间满足线性关系。由此可见,压电阻抗法能够与固体推进剂在力学性能上建立表征关系,通过得到固体推进剂结构机械阻抗能够监测其老化损伤。     

A CFD-based numerical virtual flight simulator and its application in control law design of a maneuverable missile model

A CFD-based Numerical Virtual Flight (NVF) simulator is presented, which integrates an unsteady flow solver on moving hybrid grids, a Rigid-Body Dynamics (RBD) solver and a module of the Flight Control System (FCS). A technique of dynamic hybrid grids is developed to control the active control surfaces with body morphing, with a technique of parallel unstructured dynamic overlapping grids generating proper moving grids over the deflecting control surfaces (e.g. the afterbody rudders of a missile). For the flow/kinematic coupled problems, the 6 Degree-Of-Freedom (DOF) equations are solved by an explicit or implicit method coupled with the URANS CFD solver. The module of the control law is explicitly coupled into the NVF simulator and then improved by the simulation of the pitching maneuver process of a maneuverable missile model. A nonlinear dynamic inversion method is then implemented to design the control law for the pitching process of the maneuverable missile model. Simulations and analysis of the pitching maneuver process are carried out by the NVF simulator to improve the flight control law. Higher control response performance is obtained by adjusting the gain factors and adding an integrator into the control loop.     

Stall flutter prediction based on multi-layer GRU neural network

The modeling of dynamic stall aerodynamics is essential to stall flutter, due to the flow separation in a large-amplitude pitching oscillation process. A newly neural network based Reduced Order Model (ROM) framework for predicting the aerodynamic forces of an airfoil undergoing large-amplitude pitching oscillation at various velocities is presented in this work. First, the dynamic stall aerodynamics is calculated by solving RANS equations and the transitional SST-γ model. Afterwards, the stall flutter bifurcation behavior is calculated by the above CFD solver coupled with structural dynamic equation. The critical flutter speed and limit-cycle oscillation amplitudes are consistent with those obtained by experiments. A newly multi-layer Gated Recurrent Unit (GRU) neural network based ROM is constructed to accelerate the calculation of aerodynamic forces. The training and validation process are carried out upon the unsteady aerodynamic data obtained by the proposed CFD method. The well-trained ROM is then coupled with the structure equation at a specific velocity, the Limit-Cycle Oscillation (LCO) of stall flutter under this flow condition is predicted precisely and more quickly. In order to predict both the critical flutter velocity and LCO amplitudes after bifurcation at different velocities, a new ROM with GRU neural network considering the variation of flow velocities is developed. The stall flutter results predicted by ROM agree well with the CFD ones at different velocities. Finally, a brief sensitivity analysis of two structural parameters of ROM is carried out. It infers the potential of the presented modeling method to depict the nonlinearity of dynamic stall and stall flutter phenomenon.     

航空发动机全飞行包线稳态划分方法研究

航空发动机在鲁棒控制器设计过程中存在飞行包线区域难以系统划分的问题,为此,提出基于推力耗油率特性和基于动压耗油率特性的航空发动机飞行包线划分法。根据某型涡扇发动机在全包线范围内稳态工作时的推力、耗油率及动压特性,结合大气条件的客观规律,通过两种划分方法将飞行包线划分为65 个区域,用每个区域对应标称点的参数代替其周围小偏差区域和边界点参数。通过对该发动机全包线内各区域标称点与边界点参数的对比,证明两种方法均对全飞行包线划分有效,可为后续航空发动机控制器设计提供理论基础。     

非圆等距型面轮廓X-C轴联动高速磨削试验北大核心CSCD

针对非圆等距型面轮廓磨削加工存在表面质量差的问题,建立基于恒磨除率X-C轴联动磨削理论模型。选用陶瓷CBN砂轮进行三弧段非圆等距型面轮廓的高速磨削正交试验,探究砂轮线速度、工件速度和磨削深度对磨削比能、切向磨削力、磨削温度、表面粗糙度的影响规律。分析表明,砂轮线速度对切向磨削力、表面形貌的影响最大,磨削深度对磨削比能、磨削温度、表面粗糙度的影响最大。进行表面形貌观测未探测到明显的磨削烧伤区域,证明恒磨除率X-C轴联动磨削方式可用于非圆等距型面轮廓磨削加工。     

钛合金TC4的超硬磨料柔性抛光轮数控抛光试验研究

航空发动机叶片钛合金材料在数控磨抛加工中容易发生烧伤及黏附现象,针对常用的TC4材料开展了超硬磨料柔性抛光轮数控抛光试验研究。分析了超硬磨料柔性抛光轮抛光参数中转速、进给速度、预压量及行距对抛光去除深度及抛光后试件表面粗糙度的影响规律并通过正交试验分析了各抛光参数影响的主次关系。确认了钛合金试件抛光表面黏附物质成分,并同时分析了表面黏附物的形成原理。给出了TC4钛合金材料在超硬磨料柔性抛光轮数控抛光过程中工艺参数的选择策略,为TC4材料的航空发动机叶片和整体叶盘在超硬磨料柔性抛光轮数控抛光过程中提供理论依据和技术基础。