粗糙表面偏振二向反射分布函数的影响参数及其反演

针对目标偏振二向反射特性研究中模型参数难以准确确定的问题,分析了粗糙表面偏振二向反射分布函数的影响参数,并通过理论推导和仿真计算,研究了各参数对粗糙表面散射特性的作用机理。总结分析了现有参数反演方法,针对现有方法存在的理论缺陷,在P-G(Preist-Germer)模型的基础上,提出了利用"相对偏振分量-角度"的相关关系进行参数反演的方法,设计了参数反演算法,进行了标准反射板和绿漆表面的偏振二向反射特性测试实验,并根据实验数据进行了参数反演和模型验证。实验结果表明,改进的参数反演方法可准确反演所有模型参数。利用反演参数进行模型验证,结果显示模型预测数据与实验数据具有较好的吻合度,验证了模型的准确性。     

NH－93型有机氟涂料的研究

采用国产含氟乳液为基料，研究了辅料的种类和用量，涂料的组成及工艺参数对涂膜性能的影响，提出了能获得良好涂膜的ＮＨ－９３型氟涂料的配方和成膜条件。     

200km/h动力分散型电动旅客列车组车体表面压力分布试验研究

阐述了对我国首列200km/h动力分散型电动旅客列车组(先锋号列车)车体表面压力分布测试情况,对测量结果进行了较为详细的分析,最后用流场计算软件CFX对先锋号列车周围流场进行了数值模拟计算,并将计算结果与测量结果进行了对比,两者有较好的一致性。该研究结果可为空调装置及电器设备冷却风道进排风口位置的选取提供科学依据。     

Radar Imaging of Mercury

Earth-based radar has been one of the few, and one of the most important, sources of new information about Mercury during the three decades since the Mariner 10 encounters. The emphasis during the past 15 years has been on full-disk, dual-polarization imaging of the planet, an effort that has been facilitated by the development of novel radar techniques and by improvements in radar systems. Probably the most important result of the imaging work has been the discovery and mapping of radar-bright features at the poles. The radar scattering properties of these features, and their confinement to permanently shaded crater floors, is consistent with volume backscatter from a low-loss volatile such as clean water ice. Questions remain, however, regarding the source and long-term stability of the putative ice, which underscores the need for independent confirmation by other observational methods. Radar images of the non-polar regions have also revealed a plethora of bright features, most of which are associated with fresh craters and their ejecta. Several very large impact features, with rays and other bright ejecta spreading over distances of 1,000 km or more, have been traced to source craters with diameters of 80–125 km. Among these large rayed features are some whose relative faintness suggests that they are being observed in an intermediate stage of degradation. Less extended ray/ejecta features have been found for some of the freshest medium-size craters such as Kuiper and Degas. Much more common are smaller (<40 km diameter) fresh craters showing bright rim-rings but little or no ray structure. These smaller radar-bright craters are particularly common over the H-7 quadrangle. Diffuse areas of enhanced depolarized brightness have been found in the smooth plains, including the circum-Caloris planitiae and Tolstoj Basin. This is an interesting finding, as it is the reverse of the albedo contrast seen between the radar-dark maria and the radar-bright cratered highlands on the Moon.     

中国空间大功率微波部件微放电抑制表面处理技术最新进展

材料表面的二次电子发射会触发和维持空间高功率射频器件的共振雪崩放电现象,这种现象又被称为微放电效应。微放电效应是限制空间大功率微波部件应用的关键问题之一。从微放电作用的机理出发,首先介绍了两种微放电类型（单表面与双表面）的基本物理机理;然后总结了当前主流的微放电抑制方法并给出各自应用于空间大功率微波部件时的限制。针对空间大功率微波部件微放电抑制的特殊问题,综述了国内近5年来在表面处理法抑制微放电领域的研究成果并预测了微放电抑制技术的发展趋势。     

Validation of non-linear split window algorithm for land surface temperature estimation using Sentinel-3 satellite imagery: Case study; Tehran Province,Iran

In recent years, land surface temperature (LST) has become critical in environmental studies and earth science. Remote sensing technology enables spatiotemporal monitoring of this parameter on large scales. This parameter can be estimated by satellite images with at least one thermal band. Sentinel-3 SLSTR data provide LST products with a spatial resolution of 1 km. In this research, direct and indirect validation procedures were employed to evaluate the Sentinel-3 SLSTR LST products over the study area in different seasons from 2018 to 2019. The validation method was based on the absolute (direct) evaluation of this product with field data and comparison (indirect) evaluation with the MODIS LST product and the estimated LST using the non-linear split-window (NSW) algorithm. Also, two emissivity estimation methods, (1) NDVI thresholding method (NDVI-THM) and (2) classification-based emissivity method (CBEM), were used to estimate the LST using the NSW method according to the two thermal bands of Sentinel-3 images. Then, the accuracy of these methods in estimating LST was evaluated using field data and temporal changes of vegetation, which the NDVI-THM method generated better results. For indirect evaluation between the Sentinel-3 LST product, MODIS LST product, and LST estimated using NSW, four filters based on spatial and temporal separates between pairs of pixels and pixel quality were used to ensure the accuracy and consistency of the compared pairs of a pixel. In general, the accuracy results of the LST products of MODIS and Sentinel-3, and LST estimated using NSW showed a similar trend for LST changes during the seasons. With respect to the two absolute and comparative validations for the Sentinel-3 LST products, summer with the highest values of bias (?1.24 K), standard deviation (StDv = 2.66 K), and RMSE (2.43 K), and winter with the lowest ones (bias of 0.14 K, StDv of 1.13 K, and RMSE of 1.12 K) provided the worst and best results for the seasons in the period of 2018–2019, respectively. According to both absolute and comparative evaluation results, the Sentinel-3 SLSTR LST products provided reliable results for all seasons on a large temporal and spatial scale over our studied area.     

Evaluation of SARAL/AltiKa performance using GNSS/IMU equipped buoy in Sajafi,Imam Hassan and Kangan Ports

Performance of SARAL/AltiKa mission has been evaluated within 2016 altimeter calibration/validation framework in Persian Gulf through three campaigns conducted in the offshore waters of Sajafi, Imam Hassan and Kangan Ports, while the altimeter overflew the passes 470, 111 and 25 on 13 Feb, 7 March and 17 June 2016, respectively. As the preparation, a lightweight buoy was equipped with a GNSS receiver/choke-ring antenna and a MEMS-based IMU to measure independent datasets in the field operations. To obtain accurate sea surface height (SSH) time series, the offset of the onboard antenna from the equilibrium sea level was predetermined through surveying operations as the buoy was deploying in the onshore waters of Kangan Port. Accordingly, the double-difference carrier phase observations have been processed via the Bernese GPS Software v. 5.0 so as to provide the GNSS-derived time series at the comparison points of the calibration campaigns, once the disturbing effects due to the platform tilt and heave have been eliminated. Owing to comparing of the SSH time series and the associating altimetry 1?Hz GDR-T datasets, the calibration/validation of the SARAL/AltiKa has been performed in the both cases of radiometer and ECMWF wet troposphere corrections so as to identify potential land contamination. An agreement of the present findings in comparison with those attained in other international calibrations sites confirms the promising feasibility of Persian Gulf as a new dedicated site for calibration/validation of ongoing and future altimetry missions.     

月球表层采样样品智能确认方法

表层采样是月球采样探测的重要方式，样品智能确认有助于提升工作效率与复杂问题处理能力。结合月球表层采样铲挖工作过程，分析了铲挖过程中臂载相机图像的特点，模仿有人参与识别过程，提出了层次解耦的月球样品智能识别流程，利用深度学习方法构建了一类深度卷积识别网络，完整地描述了图像、特征、标记在网络中的正反传递关系，并在月球表层采样地面试验中进行了验证，结果表明该方法对不同光照、不同背景、不同过程、不同形态的样品，具有较好的泛化识别能力，误识别率优于8.1%，平均单幅识别时间约0.7 s。     

Electrochemical micromachining of micro-dimple arrays on cylindrical inner surfaces using a dry-film photoresist

The application of surface textures has been employed to improve the tribological performance of various mechanical components. Various techniques have been used for the application of surface textures such as micro-dimple arrays, but the fabrication of such arrays on cylindrical inner surfaces remains a challenge. In this study, a dry-film photoresist is used as a mask during through-mask electrochemical micromachining to successfully prepare micro-dimple arrays with dimples 94 lm in diameter and 22.7 lm deep on cylindrical inner surfaces, with a machining time of 9 s and an applied voltage of 8 V. The versatility of this method is demonstrated, as are its potential low cost and high efficiency. It is also shown that for a fixed dimple depth, a smaller dimple diameter can be obtained using a combination of lower current density and longer machining time in a passivating sodium nitrate electrolyte.     

新型航空发动机空气冷却器流动传热性能试验

空气冷却器是航空发动机中空气热量交换的重要场所,针对传统扰动结构强化换热不足问题,重点研究了空气冷却器 中扰动结构的结构形貌特征与流动换热的关系。以三周期极小曲面结构为基础,设计制造了D型极小曲面扰动结构、P型极小曲 面扰动结构和基于Sigmoid函数杂化方法的D-P型（P-D型）结构。并利用纳米CT重构出样品的3维数字特征,试验研究了不同结 构来流速度与压降、换热性能和综合换热性能的关系。结果表明：D型极小曲面结构具有最优的压降、换热性能和综合换热性能： D-P型杂化极小曲面结构的阻力系数f最大,比D型结构的高56.81%;D型的平均努塞尔数Nu比P型的高18.49%,P-D和D-P杂 化结构的换热性能比P型结构的有效提高;P-D型D-P型杂化结构的Nu分别比P型结构的高2%和8.27%。在4种结构中,D型结 构的综合换热性能最优,分别比P型、P-D型、D-P型结构的高40.35%、57.2%、71.02%。