DCR系统的信道编译码方法研究

数字对讲机协议的制定是当前研究的热点,而信道编译码技术又是数字对讲机的关键技术之一.DCR系统吸收了dPMR系统的信道编译码方式的优点,同时采用删除卷积码纠错技术,提高了对传输差错的控制能力.对基于DCR协议的编译码方案和删除卷积码的编译码方法进行了研究,对不同编译码方式的误码率进行了深入分析.仿真结果表明：在多径衰落信道下,删除卷积码可以有效的纠正突发错误,大大降低误码率.     

多机并联火箭羽流流场及其底部热环境分析

For the problem that the plume flow field structure of a multi engine parallel rocket is complicated and the bottom thermal environment is extremely harsh, which may cause the failure of the engine structural components, the plume flow field and thermal environment at different altitudes are studied through numerical simulation. The result is compared with the measured results in flight which shows that when the rocket is flying at a low altitude, the plume of the engines do not interfere with each other. As the flight altitude increases, the plumes gradually expand and begin to interfere with each other, and finally there is an obvious backflow at the bottom of the rocket. The maximum heat flux at the moment of take off is basically the same as the measured value in flight. Before the backflow occurs, the heat flux mainly consists of radiant heat, the convective heat flow increases as the flight altitude grows, but it is also much smaller than the peak heat flow at takeoff. The result has certain guiding significance for the optimal design of engine structure thermal protection.     

Thermal-structural analysis of regenerativelycooled thrust chamber wall in reusable LOX/Methane rocket engines

To predict the thermal and structural responses of the thrust chamber wall under cyclic work,a 3-D fluid-structural coupling computational methodology is developed.The thermal and mechanical loads are determined by a validated 3-D finite volume fluid-thermal coupling computational method.With the specified loads,the nonlinear thermal-structural finite element analysis is applied to obtaining the 3-D thermal and structural responses.The Chaboche nonlinear kinematic hardening model calibrated by experimental data is adopted to predict the cyclic plastic behavior of the inner wall.The methodology is further applied to the thrust chamber of LOX/Methane rocket engines.The results show that both the maximum temperature at hot run phase and the maximum circumferential residual strain of the inner wall appear at the convergent part of the chamber.Struc tural analysis for multiple work cycles reveals that the failure of the inner wall may be controlled by the low-cycle fatigue when the Chaboche model parameter γ3 =0,and the damage caused by the thermal-mechanical ratcheting of the inner wall cannot be ignored when γ3 ＞ 0.The results of sen sitivity analysis indicate that mechanical loads have a strong influence on the strains in the inner wall.     

摆线桨非定常动态失速的三维效应

对摆线桨三维全尺寸模型进行了非定常数值模拟。验证了两种嵌套网格方法的可靠性与适用性,针对二维/三维情况下摆线桨非定常涡流动特性及诱导分离特性开展了数值分析,重点研究了展向气动力随方位角的分布与全局流场的诱导速度分布,并分析了尾迹捕捉精度与涡量耗散特征。结果表明:受摆线桨切向速度、展向诱导速度等三维效应影响,两种计算结果的瞬态气动力极值差值达到44%。三维动态失速涡的产生、脱落与再附明显弱于二维翼型情况,这对于摆线桨非定常气动特性有较大影响。      

跨介质航行器波浪环境入水流场演变和运动特性研究

跨介质航行器是一种既可以在空中飞行又可以在水下潜航的新概念航行器,基于仿生学原理,提出一种通过改变外形实现水空介质跨越的航行器模型,通过入水试验装置和计算流体动力学方法,对航行器带攻角从空气到水的介质跨越过程进行了试验和数值仿真研究,得到了跨介质入水过程航行器的运动姿态和入水空泡形态,并通过数值仿真得到了航行器的升力、阻力、速度和加速度演化规律。同时基于数值模拟方法对有波浪情况和静水情况下航行器入水过程空泡演变以及运动特性进行对比。结果表明:提出的航行器构型在水中具有较好的姿态调整能力,波浪的有无和波高的不同都会对航行体入水运动特性造成影响。     

基于遥测数据的无人机气动参数辨识方法研究

针对无人机在高空低速飞行时易受风场影响及在数据分析时遥测数据不完备的问题,进行了气动参数辨识方法研究,提出了基于空速管平面矢量三角形的风场估计方法及基于风场信息修正的气动角估计方法。以某型无人机为例,对遥测数据进行了充分分析与信息综合,运用逐步回归方法进行了纵向气动参数辨识,并进行了实验验证。结果表明,模型计算结果与实测数据吻合较好,说明所提方法有效。考虑到辨识模型的数学本质,该方法对其他固定翼无人机同样适用。     

双脉冲发动机点火过程三维数值模拟

以喷射棒式双脉冲发动机燃烧室、级间隔离装置和喷管一体化为研究对象,采用数值仿真技术对Ⅱ脉冲点火过程三维流场特性进行分析研究。计算结果表明,点火初期燃气压力波峰超前于火焰峰到达级间隔离装置,并以压强冲击波形式传播,Ⅱ脉冲燃烧室相对高压区位置不断发生改变;级间孔打开过程对药柱末端压强影响较大,但对Ⅱ脉冲燃烧室压强整体上升过程影响较小;级间孔打开后,燃气经级间孔加速后形成高度欠膨胀射流,并在Ⅰ脉冲燃烧室内形成非对称带状低压区;级间孔分布的非对称性,导致压强及温度在发动机燃烧室中呈现显著的三维分布特性;高温区出现在隔板附近,而在装药前端、装药末端及外围级间孔轴线附近出现低温区。     

复合材料制造过程仿真技术综述

复合材料制造过程仿真技术的有效应用可以在复合材料构件设计之初对其制造过程中可能出现的缺陷,如分层、孔隙、温度不均、变形等问题进行预测,从而为优化构件结构、调整工艺参数或模具型面提供依据。对目前复合材料设计制造领域常用的一些软件进行简要介绍,并针对目前复合材料制造过程温度场分布和固化变形仿真技术中存在的问题进行了阐述与讨论。     

航天器视场遮挡分析方法研究

敏感器视场遮挡分析是航天器构型布局设计的重要组成部分，针对大型在轨变构型航天器敏感器视场遮挡分析工作量大、出错率高、遮挡率无法量化等特点，本文提出一种基于敏感器第一视角的视场遮挡快速分析方法。该方法通过设置第一视角图像蒙版及图像映射，模拟方锥形、圆锥形、球形等各类敏感器视场，通过逐个像素比对，计算视场遮挡率和遮挡方位。使用此方法建立了空间站敏感器视场遮挡分析系统，结果表明新方法能够显著提高视场遮挡分析效率和准确率，并且为机构类部件运动过程对敏感器视场遮挡的分析提供了有效工具。     

Geometric calibration of Colour and Stereo Surface Imaging System of ESA’s Trace Gas Orbiter

There are many geometric calibration methods for “standard” cameras. These methods, however, cannot be used for the calibration of telescopes with large focal lengths and complex off-axis optics. Moreover, specialized calibration methods for the telescopes are scarce in literature. We describe the calibration method that we developed for the Colour and Stereo Surface Imaging System (CaSSIS) telescope, on board of the ExoMars Trace Gas Orbiter (TGO). Although our method is described in the context of CaSSIS, with camera-specific experiments, it is general and can be applied to other telescopes. We further encourage re-use of the proposed method by making our calibration code and data available on-line.