航空带垫卡箍刚度及阻尼特性分析与试验验证

研制了带垫卡箍刚度测试装置,分别对不同规格卡箍线刚度和扭转刚度进行了测量,并将卡箍刚度测量数值引入卡箍-管路系统有限元模型,通过管路固有特性数值计算与试验测试结果对比,误差在5％左右,验证了卡箍刚度参数的准确性.进一步搭建了卡箍阻尼测量系统,通过测量卡箍动态传递率,获得相对应的模态阻尼比,并将卡箍阻尼测量数值引入卡箍-...     

短螺旋型燃烧室旋流结构及气动边界发展规律数值模拟研究

短螺旋型燃烧室的头部轴线沿发动机周向与发动机轴线偏转一定角度,可以在保证燃烧效率不变的条件下有效缩短燃烧室轴向长度。短螺旋型燃烧室流场的最大特点是旋流流动单侧受限。为了研究头部安装角α变化对燃烧室旋流流动特性的影响,基于数值方法对短螺旋型燃烧室进行了计算分析。结果表明:随着α变化,旋流器下游旋涡依次出现对称环状、马蹄状、环状结构;随着α增加,气动边界逐渐出现并抑制旋流的周向扩张,导致流场出现不同的旋涡结构;不同α下的切向角动量随轴向距离增加而衰减,但α为35°和45°时,气动边界在非受限侧出现并对旋流产生约束,角动量衰减变慢;当α为0°,15°,35°,45°时,燃油液滴依次集中分布在旋流器下游两旋涡边缘、侧壁面和头部端壁、非受限旋涡边缘。本文研究了不同α下的旋涡结构及气动边界沿轴向的演化过程,为短螺旋型燃烧室进一步的设计与优化提供基础。     

基于变刚度变阻尼的柔性喷管动态模型

针对柔性接头动态迟滞曲线受控制系统控制位置精度和动态响应速度影响较大的问题,基于电液伺服机构和柔性接头变刚度变阻尼模型,构建了柔性喷管的电液伺服机构-变刚度变阻尼模型,将其和电液伺服机构-定刚度定阻尼模型进行了对比。分析了电液伺服机构主要参数、柔性接头工作参数等对电液伺服机构-柔性接头系统动态特性的影响。分析结果表明:电液伺服机构-变刚度变阻尼模型所构造的迟滞曲线可更准确地与实验结果相吻合,并符合迟滞曲线随频率变化的规律,反馈系数、放大器静态放大系数、电液伺服机构增益、滑阀流量增益等参数对系统动态特性的影响更为明显。该模型为固体火箭发动机电液伺服机构-柔性接头系统动态特性的调整提供理论依据。     

火箭发动机超声速过膨胀射流气动噪声特性研究

采用大涡模拟LES方法计算了火箭发动机超声速过膨胀射流形态及近场声压分布,研究了入口温度与环境温度的比值(温度比)对声场的影响;将声源分解,基于Ffowcs Williams-Hawkings (FW-H)方程获取了不同位置噪声源的远场噪声,并根据声压级频谱和湍流形态分析了超声速射流噪声的产生机理。研究表明,超声速过膨胀射流气动噪声由湍流混合噪声和宽频激波噪声组成,近场噪声源以马赫波形式向大方位角辐射中高频噪声,下游大尺度湍流向低方位角范围辐射低频噪声,声压级峰值频率随观测角度增大而升高;随温度比升高,马赫波辐射角度增大,噪声指向性发生改变。该研究可为运载火箭发动机地面试车或火箭发射段声学环境设计提供参考。     

Assessment on critical technologies for conceptual design of blended-wing-body civil aircraft

Civil aviation faces great challenges because of its robust projected future growth and potential adverse environmental effects. The classical Tube-And-Wing(TAW) configuration following the Cayley's design principles has been optimized to the architecture's limit, which can hardly satisfy the further requirements on green aviation. By past decades' investigations the BlendedWing-Body(BWB) concept has emerged as a potential solution, which can simultaneously fulfill metrics of noise, emission and fuel burn. The purpose of the present work is to analyze the developments of critical technologies for BWB conceptual design from a historical perspective of technology progress. It was found that the high aerodynamic efficiency of BWB aircraft can be well scaled by the mean aerodynamic chord and wetted aspect ratio, and should be realized with the trade-offs among stability and control and low-speed performance. The structure concepts of non-cylinder pressurized cabin are of high risks on weight prediction and weight penalty. A static stability criterion is recommended and further clear and adequate criteria are required by the evaluations of flying and handling qualities. The difficulties of propulsion and airframe integration are analyzed. The energy to revenue work ratios of well-developed BWB configurations are compared,which are 31.5% and 40% better than that of TAW, using state-of-art engine technology and future engine technology, respectively. Finally, further study aspects are advocated.     

捆绑火箭POGO振动动力学模型的研究

确定了捆绑火箭POGO振动动力学模型中蓄压器的最佳安装位置,简化了液体捆绑火箭动力学模型。基于AMESim软件搭建捆绑火箭动力学仿真模型,分析了蓄压器的安装位置对捆绑火箭POGO振动系统的系统阻尼比的影响,以及贮箱、直管、泵和推力室产生的作用力对系统阻尼比的影响。结果表明:蓄压器安装在芯级氧路和助推氧路的系统阻尼比提升最大,POGO振动的抑制效果最好;推力室产生的作用力对系统阻尼比的影响占主导地位,故仅需考虑推力室产生的作用力,以简化捆绑火箭POGO振动动力学模型。该研究可应用于POGO振动的仿真过程。     

用于叶片减振的压电材料分布拓扑优化

提出一种可用于实际叶盘结构的压电分支阻尼器拓扑优化方法,可以给出总质量受约束的压电材料在叶片上的最佳分布,达到尽可能大的模态阻尼比。通过理论推导说明:压电阻尼器所产生的模态阻尼比仅取决于模态机电耦合系数,且该系数只与压电材料的几何形状以及模态应力场有关。进一步结合压电本构关系,基于应力分量的线性加权给出了有限的压电材料在叶片上铺设位置“优先级”的判断指标。给出了基于叶盘结构有限元模型的压电材料拓扑优化方法,通过替换单元类型和材料参数的方式对压电材料进行布置,并给出了多模态族优化、极化方向设置、电极铺设等问题的解决方案。在一个接近真实的叶盘模型上应用了此优化方法。结果表明,仅使用质量占叶片质量10%的压电材料,就可以为多个模态提供约12%的阻尼比。      

Application of a PCA-DBN-based surrogate model to robust aerodynamic design optimization

An efficient method employing a Principal Component Analysis (PCA)-Deep Belief Network (DBN)-based surrogate model is developed for robust aerodynamic design optimization in this study. In order to reduce the number of design variables for aerodynamic optimizations, the PCA technique is implemented to the geometric parameters obtained by parameterization method. For the purpose of predicting aerodynamic parameters, the DBN model is established with the reduced design variables as input and the aerodynamic parameters as output, and it is trained using the k-step contrastive divergence algorithm. The established PCA-DBN-based surrogate model is validated through predicting lift-to-drag ratios of a set of airfoils, and the results indicate that the PCA-DBN-based surrogate model is reliable and obtains more accurate predictions than three other surrogate models. Then the efficient optimization method is established by embedding the PCA-DBN-based surrogate model into an improved Particle Swarm Optimization (PSO) framework, and applied to the robust aerodynamic design optimizations of Natural Laminar Flow (NLF) airfoil and transonic wing. The optimization results indicate that the PCA-DBN-based surrogate model works very well as a prediction model in the robust optimization processes of both NLF airfoil and transonic wing. By employing the PCA-DBN-based surrogate model, the developed efficient method improves the optimization efficiency obviously.     

基于重叠网格的唇口移动变几何进气道数值模拟研究

吸气式冲压发动机的进气道需要在比较宽广的马赫数范围内工作,而变几何进气道具有良好的气动性能,成为了最佳选择。重叠网格技术是解决存在复杂运动边界流动模拟问题的有效策略,在应用于变几何进气道非定常流动模拟时需要进一步完善。采用发展的重叠网格技术,对变几何平动方式的进气道开展了数值模拟研究。针对存在物面接触重叠网格的挖洞操作在执行时无法取得合理的插值模板问题,引入了虚拟单元赋值方法和“Collar”网格方法,实现了多体相交时重叠网格的计算。为了引入“Collar”型重叠网格,对其算法作了适当修改以适应本论文所建立的洞面优化方法。对平移过程中内收缩变化所造成的对启动过程的影响进行了研究。通过迎着来流方向平移唇口,增大了进气道的内收缩比,导致内压缩段出现边界层分离,分离泡随着唇口的前移而增大,当其移出内压缩段时,原本启动的进气道进入不启动状态,而后移唇口减小了内收缩比,使分离泡减小并向下游移动,辅以边界层排移,可以改善进气道的启动性能。此外,平移速度和振荡频率对启动过程的影响也进行了研究,进气道迟滞效应随平移速度和振荡频率增大而增大。     

遗传算法在机翼气动优化设计中的应用

把最优化方法与机翼的气动力求解相结合,进行跨音速机翼的气动优化设计。采用最优化方法为遗传算法,机翼的气动力由三维欧拉方程的数值解来提供。与基准机翼相比较,优化设计的机翼其气动性能有较大幅度的提高,表明遗传算法在机翼优化设计中的可行性和有效性