基于累积磨损量分布的飞机刹车片可靠性分析

针对高可靠、长寿命型产品可靠性分析难于获得寿命数据的问题,基于累积磨损量分布研究刹车片的可靠性评估方法。在飞机刹车片退化机理分析的基础上,选择正态分布、对数正态分布、威布尔分布描述其累积磨损量,通过建立累积磨损量分布参数的时序模型,确定未来时刻累积磨损量的分布,对刹车片进行寿命预测。     

内燃波转子发动机循环分析

为研究内燃波转子发动机性能变化规律,建立内燃波转子发动机的气动热力循环分析模型,开展了内燃波转子对燃气轮机总体性能的影响研究,并进行影响内燃波转子发动机总体性能的参数分析,且针对现役涡轴发动机,结合波转子技术,给出5种组合方式。结果表明内燃波转子能够显著地提高燃气轮机的总体性能,循环功最大提高39%,耗油率最大降低28%。提高涡轮进口温度可以提高内燃波转子发动机的总体性能;存在使循环功达到最大值的最佳压气机压比,且涡轮进口温度越高,最佳压气机压比越大。在基准燃气轮机与内燃波转子的组合方式中,保证压气机部件以及涡轮进口温度不变,能最大限度地提高燃机轮机的性能。     

两级入轨运载器RBCC动力系统内流道设计与性能计算

针对以火箭基组合循环(RBCC)发动机作为水平起飞两级入轨(TSTO)运载器第一级动力系统的方案,建立了进气道-燃烧室-尾喷管一体化流道耦合性能快速计算模型,初步设计了RBCC发动机一体化内流道。RBCC发动机使用变结构进气道,采用支板/凹腔相结合实现火焰稳定的燃烧室以及单侧膨胀尾喷管;应用经过校验的性能分析模型进行RBCC燃烧室性能快速计算;对比分析了性能分析模型与三维数值计算获得的发动机出口状态参数对于飞行器后体流场的影响性;完成了RBCC为动力的两级入轨方案飞行器动力系统的性能分析与计算;分析评估了飞行弹道条件下RBCC推进系统的性能。计算结果表明:飞行器起飞质量280t时,可以完成运送4t载荷进入近地轨道的任务。     

涡扇发动机轴对称引射收敛喷管红外辐射特性

数值研究了涡扇发动机轴对称引射收敛喷管的红外辐射特性.排气系统的流场计算采用商用数值模拟软件,红外辐射特性计算采用自主开发的软件NUAA-IR,计算分析了轴对称收敛喷管和引射收敛喷管在3~5μm波段红外辐射特性以及喷管内不同固体壁面在探测方向上的红外辐射贡献.结果表明:引射收敛喷管的红外抑制作用主要在于引射加强了尾喷流与环境大气的掺混,减小了尾喷流的长度,降低了燃气流的红外辐射;引射收敛喷管对喷管内固体壁面的遮挡以及降温作用很小,只在方位角为20°方向上对内涵壁面、外涵内壁等中低温壁面有效;引射收敛喷管的总积分辐射强度在方位角为0°~15°范围内与收敛喷管几乎相等,在其他方位角范围内均小于收敛喷管,且在方位角为40°方向上降低幅度达到最大,约为34%.      

Attitude control system design and on-orbit performance analysis of nano-satellite––‘‘Tian Tuo 1’’

‘‘Tian Tuo 1'(TT-1) nano-satellite is the first single-board nano-satellite that was successfully launched in China. The main objective of TT-1 is technology demonstration and scientific measurements. The satellite carries out the significant exploration of single-board architecture feasibility validation, and it is tailored to the low-cost philosophy by adopting numerous commercialoff-the-shelf(COTS) components. The satellite is featured with three-axis stabilization control capability. A pitch bias momentum wheel and three magnetic coils are adopted as control actuators.The sun sensors, magnetometers and a three-axis gyro are employed as the measurement sensors.The quaternion estimator(QUEST) and unscented Kalman filter(UKF) method are adopted for the nano-satellite attitude determination. On-orbit data received by ground station is conducted to analysis the performance of attitude determination and control system(ADCS). The results show that the design of ADCS for TT-1 is suitable, robust and feasible.     

Dynamic analysis of C/C composite finger seal

A seal device as an important component of aeroengines has decisive influence on per- formance, reliability, and working life of aeroengines. With the development of aeroengines, demands on the performance characteristics of seal devices are made strictly. Finger seal as a novel kind of sealing device, recently attracts more and more attentions in academic circles and engineer- ing fields at home and abroad. Research on finger seals has been extensively developed, especially on leakage and wear performances under dynamic conditions. However, it is a pity that the work on finger seals has been limited with a single approach that is improving the performance by structural optimization; in addition, the technology of dynamic analysis on finger seals is weak. Aiming at the problems mentioned above, a distributed mass equivalent dynamic model of finger seals considering the coupling effect of overlaid laminates is established in the present paper, the dynamic perfor- mance of 2.5 dimension C/C composite finger seal is analyzed with the model, and then the effects of fiber bundle density and fiber bundle preparation direction on finger seal＇s dynamic performance are discussed, as well as compared with those of Co-based alloy finger seal. The current work is about dynamic analysis of finger seals and application of C/C composite in this paper may have much academic significance and many engineering values for improving research level of finger seal dynamics and exploring feasibility of C/C composite being used for finger seals.     

基于技术参数评估的涡扇发动机总体性能设计分析

为了充分掌握各代涡扇发动机技术参数水平及其发展趋势,统计包括现役型号在内的15台2～4代涡扇发动机的总体性能参数、循环参数和部件参数,采用考虑涡轮冷却的总体性能计算和重量预测相结合的发动机技术参数综合评估模型并利用计算程序绘制趋势曲线,评估技术参数的发展趋势,结果表明技术参数逐年改善的趋势是比较稳定的,并用曲线趋势外推法取得下一代关键参数的定量数据。在此基础上探索下一代高推重比涡扇发动机可能的总体性能方案,为下一代先进涡扇发动机的预研和设计提供参考。     

多尾鳍仿生航行器推进性能的三维数值研究

采用格子波尔兹曼方法及浸没边界法,发展了一套适用于自由游动的三维数值研究程序。进而以多尾鳍推进仿生航行器为原型,讨论了尾鳍数目、形状、材料刚度等构型参数及振幅、频率等尾鳍摆动参数对推进性能的影响。结果表明对称布置、反对称摆动的双尾鳍能够明显消除侧向力而避免航行器主体的横向晃动,且推力大于两个单独尾鳍的简单加和;在中等Reynolds数下,具有波动性质的柔性尾鳍不论是推进速度还是推进效率均优于刚性尾鳍;当尾鳍单纯摆动推进时,具有完整鳍面的半椭圆形尾鳍的推进性能优于后部有缺口的深叉形尾鳍。     

军用直升机雷达隐身性能仿真与评估

采用高频方法计算了某型通用直升机及其隐身改型的RCS数据,基于现有雷达隐身性能计算方法和直升机低空飞行特点,对直升机在单部雷达和雷达组网两种情况下的雷达隐身性能进行仿真分析,给出了单部雷达和雷达组网发现目标的判定准则,分析了直升机可探测范围曲线、平均综合检测概率和暴露时间等隐身指标。通过仿真分析,评估了不同飞行高度下RCS减缩与直升机隐身性能的定量关系,为直升机的隐身设计提供了参考依据。     

高超声速二元进气道前体曲线激波逆向设计

为实现高超声速二元进气道前体激波的压缩能力、压缩效率、流量捕获特性和结构长度可控,提出了平面曲线激波逆向设计方法。采用B-Spline曲线控制激波形状。利用有旋特征线法,求解激波的影响域及决定激波的壁面。设计了一凹激波,并对波后流场进行CFD无黏数值模拟,CFD结果和设计结果一致,验证了设计方法的可行性。此外,还设计了直激波、凹激波和凸激波3种激波,并对其在设计点和非设计点处的性能开展了数值研究。在设计点处,分析了激波的压缩比、激波的总压恢复系数、激波压缩区的压升、激波压缩区出口马赫数和流动角随激波控制角的变化规律。在非设计点处,分析了激波压缩区的流量系数和总压恢复系数随攻角和马赫数的变化规律。