300M钢零件深盲孔内键槽的磨削加工

介绍了采用在普通车床上加装专用磨槽动力头的方法，对３００Ｍ钢深盲孔内键槽进行磨削加工     

蜂窝结构的电火花磨削技术

介绍对罗．罗发动机扇形密封件的加工，阐述了ＲＤＩＡ型数控电火花机床对复杂型面峰结构电火花磨削的技术要点。     

HAN基绿色推进剂点火技术研究进展

针对HAN基绿色推进剂普遍存在点火困难的问题,总结了国内外HAN基绿色推进剂点火技术的研究和应用情况。HAN基液体推进剂的点火方式主要包括催化分解点火、电火花点火、无弧点火、电解点火和激光点火。HAN基凝胶推进剂仍采用传统烟火药方式,难以实现点火。HAN基固体推进剂采用电极电解点火方式,在电压的控制下实现了点火、燃烧和熄火可控。分析认为,采用电解方式能够显著提高HAN推进剂的点火效率,是HAN基推进剂点火技术的发展方向。     

Design and experimental study of a micro-groove grinding wheel with spray cooling effect

The effectiveness of grinding fluid supply has a crucial impact on grinding quality and efficiency in high speed grinding. In order to improve the cooling and lubrication, through in-depth research of self-inhaling internal cooling method and intermittent grinding mechanism, a new spray cooling method used in high speed grinding is proposed. By referring to the structure of bowl- shaped dispersion disk, the grinding wheel matrix with atomization ability is designed; through studying heat transfer of droplet collision and the influence of micro-groove on the boiling heat transfer, grinding segment with micro-groove is designed to enhance the heat flux of coolant and achieve maximum heat transfer between droplets and grinding contact zone. High-speed grinding experiments on GH4169 with the developed grinding wheel are carried out. The results show that with the micro-groove grinding wheel just 5.4% of pump outlet flow rate and 0.5% of spindle energy is needed to reduce the grinding temperature to 200℃, which means the developed grinding wheel makes cooling high efficient and low energy consuming.     

Grinding performance evaluation of porous composite-bonded CBN wheels for Inconel 718

For high-efficiency grinding of difficult-to-cut materials such as titanium and nickel alloys, a high porosity is expected and also a sufficient mechanical strength to satisfy the function.However, the porosity increase is a disadvantage to the mechanical strength. As a promising pore forming agent, alumina bubbles are firstly induced into the abrasive layer to fabricate porous cubic boron nitride（CBN） wheels. When the wheel porosity reaches 45%, the bending strength is still high up to 50 MPa with modified orderly pore distribution. A porous CBN wheel was fabricated with a total porosity around 30%. The grinding performance of the porous composite-bonded CBN wheel was evaluated in terms of specific force, specific grinding energy, and grinding temperature, which were better than those of the vitrified one under the same grinding conditions. Compared to the vitrified CBN wheel, clear straight cutting grooves and less chip adhesion are observed on the ground surface and there is also no extensive loading on the wheel surface after grinding.     

页轮干式磨削Ti6Al4V合金

进行了Ti6A14V合金锆刚玉页轮和碳化硅页轮的磨削性能试验研究，分析了磨削用量对磨削力、磨削温度和磨削表面完整性的影响。磨削力通过KISTLER9265B测力仪测定，磨削表面温度由NIUSB-621X信号采集系统测得，磨削表面形貌和金相组织由HiroxKH-7700型体视显微仪和Quanta200型扫描电镜（SEM）观察，表面粗糙度由Mahr Perthometer M1粗糙度仪测得，表层显微硬度通过HVS—1000硬度计测定。研究结果表明：页轮磨削钛合金工件表面没有发生烧伤现象，磨削热影响区厚度小于50μm，锆刚玉页轮比碳化硅页轮更适合干式磨削钛合金。     

单层钎焊砂盘磨粒分布有序性研究

对亲型非砂轮磨削工具－－单层钎焊砂盘的硬质合金磨粒在基体上的分布进行了初步研究，砂盘作为一种手握粗磨削工具，降低磨削力是最重要的，文中借鉴砂带及单层高温钎焊超硬磨料砂轮的一些研究，提出了砂盘的磨粒在基体上有序性分布的概念，将此概念应用于砂盘钎焊制造工艺上，在相同的制造工艺和磨洵深度条件下，对得到的磨粒有序性及无序性分布的砂盘进行了磨削对比实验。结果表明，砂盘磨粒的有序性分布能显著降低其磨削力。此概     

具有参数编程功能的陶瓷刀片磨削加工数控系统

提出了一种适用于陶瓷刀片加工的新的插补算法，介绍了基于此算法的陶瓷刀片磨削加工数控系统。此插补算法大大简化了系统设计，提高了刀片的加工精度。用该系统精心设计的５个加工指令，即可完成所有标准刀片和大部分非标准刀片的加工编程。利用系统的参数编程功能，操作者只需选择刀片形状并输入刀片参数，系统可自动生成零件加工程序，完成刀片的加工。     

缓进给强力磨削及其应用

综述了缓进给强力磨削的特点、关键技术及应用。