神舟2号大气密度探测器的探测结果(Ⅰ)日照和阴影区域热层大气密度变化

选用了神舟2号（SZ-2）大气密度探测器在2001年2—4月间的探测数据,进行日照和阴影区域热层大气密度变化的探讨.结果表明:在高度410km附近,日照和阴影区域大气密度变幅为2—3倍,变幅的大小与地磁活动程度呈负相关关系.日照面大气密度峰区位于星下点地方时1400—1500LT的纬度处,峰值大小与太阳活动程度呈正相关关系.阴影面大气密度谷区位于星下点地方时0400-0500的纬度处,同时在±10°纬度区域中还出现了阴影面峰区.     

线阵CCD平场校正及FPGA实现的研究

为了消除由于照明光源的非均匀性、镜头渐晕及CCD传感器噪声对图像质量造成的不良影响,首先从理论上分析了线阵CCD固定模式噪声和像素光电响应非均匀性的数学模型和产生的原因;对像素光电响应非均匀性这一主要影响因素,根据其光电响应模型提出了CCD像素光电响应非均匀性的两点校正方法,即求解出各个像素光电响应不均匀性的校正因子和暗偏置量系数,进而用以计算各个像素的校正量,实现逐点校正;针对校正算法大数据量、实时计算的要求,设计了基于现场可编程逻辑门阵列FPGA快速实现校正算法的硬件处理结构。最后,通过仿真和实验表明,两点校正方法可以有效地减小CCD像素光电响应不均匀性的图像噪声,提高图像质量,以便做后续精确处理。     

高超声速滑翔再入定向定速打击末制导算法

以具有终端落角和落速约束的小升阻比短距滑翔高超声速再入打击飞行器为研究对象，通过引入弹道调整段来实现对飞行器的初步大幅度减速，并使其满足中末制导交班条件，以解决飞行器捕获目标后难以直接对其进行定向定速打击的问题。首先设计了一种变角偏差反馈系数的偏置比例制导律，解决了末端攻击段弹道下压困难以及导引头视场稳定跟踪等问题。在此基础上，建立了一种基于攻角和弹道倾角估计的末端减速指令生成方法，有效解决了基于理想速度曲线减速控制方法精度不足的问题。因此，数值仿真结果表明该制导方案能够有效控制飞行器终端落角和落速，并具有较高的制导精度。     

静止轨道卫星通信链路的预算与分析

星地链路计算作为卫星通信的重要技术，是卫星通信系统设计的基础和理论依据，直接决定了卫星通信系统的链路通信质量。由于影响卫星链路的因素很多，设计中存在一处不合理即使得整条星地链路不可用，造成巨大的损失。而且在实际设计中无法做到最理想的链路状态，往往需要在某方面有所取舍，这也是链路计算中的一大难点。基于目前国际通用的链路计算方法，将星地链路上下行拆分，独立计算，综合分析，再结合实际工程经验，分析和计算实际工程案例，针对不同的链路配置给出相应合理的设计方法，可作为静止轨道通信卫星星地链路计算分析的参考。     

A new dynamic pushback control method for reducing fuel-burn costs: Using predicted taxi-out time

Long departure-taxi-out time leads to significant airport surface congestion, fuel-burn costs, and excessive emissions of greenhouse gases. To reduce these undesirable effects, a Predicted taxi-out time-based Dynamic Pushback Control(PDPC) method is proposed. The implementation of this method requires two steps: first, the taxi-out times for aircraft are predicted by the leastsquares support-vector regression approach of which the parameters are optimized by an introduced improved Firefly algorithm. Then, a dynamic pushback control model equipped with a linear gate-hold penalty function is built, along with a proposed iterative taxiway queue-threshold optimization algorithm for solving the model. A case study with data obtained from Beijing International airport(PEK) is presented. The taxi-out time prediction model achieves predictive accuracy within 3 min and 5 min by 84.71% and 95.66%, respectively. The results of the proposed pushback method show that total operation cost and fuel-burn cost achieve a 14.0% and 21.1%reduction, respectively, as compared to the traditional K-control policy.(3) From the perspective of implementation, using PDPC policy can significantly reduce the queue length in taxiway and taxi-out time. The total operation cost and fuel-burn cost can be curtailed by 37.2% and 52.1%,respectively, as compared to the non-enforcement of any pushback control mechanism. These results show that the proposed pushback control model can reduce fuel-burn costs and airport surface congestion effectively.     

Early analysis of precise orbit and clock offset determination for the satellites of the global BeiDou-3 system

Eight new-generation BeiDou satellites (BeiDou-3) have been launched into Medium Earth Orbit (MEO), allowing for global coverage since March 2018, and they are equipped with new hydrogen atomic clocks and updated rubidium clocks. Firstly, we analyzed the signals for the carrier-to-noise-density ratio (C/N0) and pseudorange multipath (MP) by using international GNSS (Global Navigation Satellite System) Monitoring and Assessment System (iGMAS) station data, and found that B1C has a lower C/N0, and B2a has the same level of C/N0 as the B1I and B3I signals. For pseudorange multipath, compared with the BeiDou-2 satellites, the obvious systematic variation of MP scatters related to the elevation angle is greatly improved for the BeiDou-3 and BeiDou-3e satellites signals. For the signals of the BeiDou-3 satellites, the order of the Root Mean Square (RMS) values of multipath and noise is B3I?<?B1I?<?B2a?<?B1C. Then, the comparison of the precise orbit determination and clock offset determination for the BeiDou-2, BeiDou-3, and BeiDou-3 experimental (BeiDou-3e) satellites was done by using 10 stations from iGMAS. The 3D precision of the 24?h orbit overlap is 24.55, 25.61, and 23.35?cm for the BeiDou-3, BeiDou-3e, and BeiDou-2 satellites, respectively. BeiDou-3 satellite has a comparable precision to that of the BeiDou-2 satellite. For the precision of clock offset estimation, the Standard Deviation (STD) of the BeiDou-3 MEO satellite is 0.350?ns, which is an improvement of 0.042?ns over that of the BeiDou-2 MEO satellite. The stabilities of the BeiDou-3 and BeiDou-3e onboard clocks are better than those of BeiDou-2 by factors of 2.84 and 1.61 at an averaging time of 1000 and 10,000?s, respectively.     

Aircraft nonlinear stability analysis and multidimensional stability region estimation under icing conditions

Icing is one of the crucial factors that could pose great threat to flight safety,and thus research on stability and stability region of aircraft safety under icing conditions is significant for control and flight.Nonlinear dynamical equations and models of aerodynamic coefficients of an air craft are set up in this paper to study the stability and stability region of the aircraft under an icing condition.Firstly,the equilibrium points of the iced aircraft system are calculated and analyzed based on the theory of differential equation stability.Secondly,according to the correlation theory about equilibrium points and the stability region,this paper estimates the multidimensional stability region of the aircraft,based on which the stability regions before and after icing are compared.Finally,the results are confirmed by the time history analysis.The results can give a reference for stability analysis and envelope protection of the nonlinear system of an iced aircraft.     

阵风载荷减缓系统故障分析

阵风引起的额外载荷会引起飞机结构疲劳,降低结构使用寿命。采用非定常气动力有理函数拟合方法建立时域状态空间下的动力学系统,设计了阵风载荷减缓系统。研究了阵风载荷减缓系统3种典型故障模式(副翼偏转饱和、舵机卡死、副翼偏转延时)的力学建模方法,并对机翼在阵风减缓系统故障模式下的阵风响应进行分析。仿真结果表明,3种故障模式均不利于阵风载荷减缓系统对阵风载荷的减缓,对于一些特定情况,故障模式下的阵风载荷减缓系统不仅不能减缓阵风载荷,还会带来由副翼偏转不当引起的额外负载。     

EPDM包覆层热解状态下的力学行为及本构模型

为了准确描述固体火箭发动机三元乙丙(EPDM)包覆层在不同热解状态下的力学特性,通过热重分析的方法得到EPDM的热解温度范围,并采用准静态单轴拉伸实验的方法获得EPDM在不同热解温度下的应力-应变曲线。以Ogden(n=2)模型为基础,分别对不同热解状态下的力学曲线进行建模,并通过对实验数据的拟合获得模型参数。结果表明,在初始热解状态下,材料只发生了少量的失水和气体的逃逸,其力学行为可通过粘超弹本构模型进行描述;随着材料热解程度增加,基体材料和填充纤维均遭到破坏,其力学行为表现为超弹脆性材料特性。