金属弹簧管性能影响因素的仿真分析

为了研究高温密封组件金属弹簧性能,本文通过对波音公司编网状弹簧管结构和Streck心脏支架结构的研究,建立了编织弹簧的几何拓扑构型和数学模型,推导了弹簧直径计算公式。采用AUTODESK3D-MAX构建了编织弹簧的仿真模型,用ANSYS仿真软件分别从编织丝直径、编织密度以及编织方法 3方面探究不同测试对弹簧性能的影响。结果表明,增加弹簧丝直径、降低弹簧管轴向方向的编织密度、提高圆周方向的编织密度、向外的弹簧管编织方式可有效提高弹簧管的回弹性能。     

流-固-推进耦合下的机体/推进一体化性能分析

吸气式空天飞行器的一体化性能随扰动变化的敏感性高,在高马赫数飞行条件下,有必要开展流-固-推进耦合性能分析。针对机体/推进一体化布局的吸气式飞行器,明确一体化部件之间的耦合关系和耦合问题,利用CFD、有限元和准一维流方法,结合本征正交分解(Proper Orthogonal Decomposition,POD)降阶手段,建立吸气式空天飞行器流-固-推进多物理场耦合快速分析方法,并开展多场耦合特性分析。结果表明:(1)进气道压缩面的流-固耦合导致出口静压的最大振荡振幅约为平均静压的21.6%,而出口马赫数的最大振幅约为平均马赫数的8.45%。(2)进气道出口性能的振荡会影响发动机的推力性能,导致推力振荡幅值可达平均值的31%,且随着时间的推移,会在进气道外压缩流场产生大量的气动涡,涡结构进入进气道后会导致进气道出口性能的持续下降,进一步削弱了发动机的平均推力性能。     

指数分布基于多重定数截尾样本中异常数据的检验

讨论多重定数截尾指数型寿命数据,对同时存在异常大数据和异常小数据的情形给出了检验方法,得到了检验异常数据的判别标准,最后以一实例说明其应用.     

机械振动全息分析及其若干问题

本文用球面波多重象全息照相分析物体的机械振动,简要地讨论了球面波多重象全息三维振动分析的基本规律,介绍了用计算机控制的显微光密度计确定由测点振动引起的物光波的相位差技术,用几何光学方法推导了曲面测件图象上测点位置的修正公式,提出了提高全息振动条纹分辨率的方法.本文在15cm长度物体上至少可记录105级能分辨的全息振型条纹.     

基于改进遗传算法的机器人动态路径规划

针对基本遗传算法解决移动机器人路径规划的不足，提出了一种改进的遗传算法。首先，采用栅格法对机器人路径规划进行建模。然后，提出一种生成初始种群的方法和精英策略，设计出自适应变异概率，提高了算法的求解质量。同时，在规划过程中，将全局路径规划与局部路径规划相结合，并且根据机器人与动态障碍物碰撞类型的不同，提出了相应的避碰策略。仿真实验表明:该算法优于基本遗传算法，能够有效地指导机器人在动态环境中实现避障，获得无碰最优或次优路径。     

低速高湍流度90°弯管流动数值模拟

分析了曲率对弯曲管道流动的影响 ,给出了曲率修正的双层 k-ε湍流模型 ,并数值模拟了非均匀来流低速高湍流度 90°弯管内流动。文中比较了曲率修正双层 k- ε湍流模型的计算结果与实验结果 ,以及双层 k- ε湍流模型和逆压力梯度修正双层 k- ε湍流模型的计算结果。通过比较 ,发现经过曲率修正后的双层 k- ε湍流模型更好地模拟了非均匀来流低速高湍流度 90°弯管内流动。同时比较了壁面参数的插值方法 ,发现在弯曲管道流动模拟中对壁面参数进行一阶插值比零阶插值能更好地模拟真实流场     

移相谐振PWM技术的研究

本文着重讨论在高频应用场合下的移相零电压谐振ＰＷＭ 技术，分析移相型谐振变换器、谐振腔电路及定频ＰＷＭ（脉宽调制）技术中的设计规范。     

专用瞄准设备自动检定系统

介绍了专用瞄准设备自动检定系统的系统配置、工作原理及软件设计，并对系统的测量不确定度进行了分析和评定。     

GRACE gravity field modeling with an investigation on correlation between nuisance parameters and gravity field coefficients

The GRACE (Gravity Recovery And Climate Experiment) monthly gravity models have been independently produced and published by several research institutions, such as Center for Space Research (CSR), GeoForschungsZentrum (GFZ), Jet Propulsion Laboratory (JPL), Centre National d’Etudes Spatiales (CNES) and Delft Institute of Earth Observation and Space Systems (DEOS). According to their processing standards, above institutions use the traditional variational approach except that the DEOS exploits the acceleration approach. The background force models employed are rather similar. The produced gravity field models generally agree with one another in the spatial pattern. However, there are some discrepancies in the gravity signal amplitude between solutions produced by different institutions. In particular, 10%–30% signal amplitude differences in some river basins can be observed. In this paper, we implemented a variant of the traditional variational approach and computed two sets of monthly gravity field solutions using the data from January 2005 to December 2006. The input data are K-band range-rates (KBRR) and kinematic orbits of GRACE satellites. The main difference in the production of our two types of models is how to deal with nuisance parameters. This type of parameters is necessary to absorb low-frequency errors in the data, which are mainly the aliasing and instrument errors. One way is to remove the nuisance parameters before estimating the geopotential coefficients, called NPARB approach in the paper. The other way is to estimate the nuisance parameters and geopotential coefficients simultaneously, called NPESS approach. These two types of solutions mainly differ in geopotential coefficients from degree 2 to 5. This can be explained by the fact that the nuisance parameters and the gravity field coefficients are highly correlated, particularly at low degrees. We compare these solutions with the official and published ones by means of spectral analysis. It is found that our solutions are, in general, consistent with others in the spatial pattern. The water storage variations of the Amazon, Chari and Ganges river basins have also been computed. The variations computed with the NPARB approach are closer to those produced by JPL and DEOS solutions, while the variations produced with the NPESS approach are in good agreement with those produced by the CSR and GFZ solutions. A simulation study is implemented with considering realistic noise and low-frequency error. The two approaches are used to recover the true model. The NPESS solution appears closer to the true one. Therefore we are inclined to estimate the nuisance parameters simultaneously with the geopential coefficients.     

低速增压风洞模型支撑系统中的角度机构控制

介绍了在低速增压风洞模型支撑系统中以单片机为核心构建的角度机构控制系统.该控制系统利用单片机接口电路实现了对伺服电机的控制及与上位机之间通信、数据传榆,解决了模型支撑系统中由于机械回差带来的精度问题以及角度机构支杆非线性运动带来的模型控制问题,达到了风洞试验要求的控制精度.