控制系统通用综合测试系统组建研究

在分析系统需求和基本功能的基础上 ,采用VXI总线技术、远程测控技术和测试应用程序自动生成等关键技术 ,按照综合测试的总体要求进行系统集成 ,组建控制系统通用综合测试系统 ,包括系统硬件和软件方案 ,对系统的硬件结构方案、模件选型以及软件流程、组成和作用进行了详细讨论。     

线阵CCD平场校正及FPGA实现的研究

为了消除由于照明光源的非均匀性、镜头渐晕及CCD传感器噪声对图像质量造成的不良影响,首先从理论上分析了线阵CCD固定模式噪声和像素光电响应非均匀性的数学模型和产生的原因;对像素光电响应非均匀性这一主要影响因素,根据其光电响应模型提出了CCD像素光电响应非均匀性的两点校正方法,即求解出各个像素光电响应不均匀性的校正因子和暗偏置量系数,进而用以计算各个像素的校正量,实现逐点校正;针对校正算法大数据量、实时计算的要求,设计了基于现场可编程逻辑门阵列FPGA快速实现校正算法的硬件处理结构。最后,通过仿真和实验表明,两点校正方法可以有效地减小CCD像素光电响应不均匀性的图像噪声,提高图像质量,以便做后续精确处理。     

Multi-mode optimal fuzzy active vibration control of composite beams laminated with photostrictive actuators

Firstly, a multi-field coupling finite element formulation of composited beam laminated with the photostrictive actuators is developed in this paper. Moreover, an optimal fuzzy active control algorithm is also proposed on the basis of the combination of optimal control and fuzzy one.This method opens a new avenue to resolve the contradiction between the linear system control method and nonlinear actuating characteristics of photostrictive actuators. The desired control for suppressing multi-modal vibration of photoelectric laminated beam is firstly obtained through optimal control and then the fuzzy control is used to approach the desired mechanical strain induced by photostrictive actuators. Thus, the multi-mode vibration control of beam is realized.In the design process of optimal fuzzy controller, the design of fuzzy control is independent of optimal control. The simulation results demonstrate that the proposed control method can effectively realize multi-modal vibration control of photoelectric laminated beams, and the control effect of optimal fuzzy control is better than that of optimal state feedback control.     

Crystal orientation and morphology of a lamellae in wrought titanium alloys: On the role of microstructure evolution in b processing

To obtain high-quality aviation forgings of titanium alloys, b forging is an essential processing step which must be considered throughout a production process. In this work, the effect of b forging on the crystal orientation and morphology of lamellar a was experimentally investigated in a two-phase titanium alloy. Strong dynamic recovery during b working resulted in the formation of low-angle grain boundary(LAGBb) inside b grains. The lamellar a can penetrate through the LAGBb, leading to similar intra a LAGBs on subgrain boundaries. Deformation banding occurs at high strain rates, and both diffusive and sharp boundaries of deformation bands can be observed.A continuous change of the b orientation in diffusive boundaries results in the formation of fine and disordered a lamellae without intra-lamellar boundary to hold the Burgers orientation relationship(OR). On sharp boundaries, it is prone to producing continuous grain boundary a(aGB) with a highly similar orientation along the boundaries. Meanwhile, there may exist several lower-angle boundaries within the grain boundary a for a smoother orientation change on the b grain boundary.     

基于新型丝状电极等离子体激励器的前体涡控制

本文首次将新型丝状暴露电极DBD等离子激励器应用于大迎角下细长体非对称涡控制。丝状暴露电极的材料的选择对DBD推力以及推力效率至关重要,通过地面精细推力测量对丝状暴露电极等离子体激励器进行了优化,结果表明,本文研究材料中采用钨丝作为暴露电极,其推力效率最优;且随着电极直径从d=0.3 mm减小到d=0.08 mm,DBD推力效率显著提升。基于优化后的DBD激励器,将其应用于前体非对称涡控制:未施加等离子体控制时,压力测量以及PIV结果均表明细长体背风区流场为明显的非对称涡结构;在等离子体激励下,该非对称涡结构可变为对称甚至反向非对称,且非稳态激励控制能力明显优于稳态激励。研究发现,大迎角下细长体非对称涡控制与背风区原始涡系结构有关,其中包含对称涡系和非对称涡系。本文研究为大迎角下细长体非对称涡控制提供了一种新思路,同时也为丝状暴露电极DBD等离子体激励器的应用提供参考。     

GAP/环氧化合物体系胶片的制备与性能表征

为探索一种新型非异氰酸酯固化体系,以端羟基聚叠氮缩水甘油醚(GAP)为研究对象,三羟甲基丙烷三缩水甘油醚(TMPTGE)为固化剂,通过实验筛选出六亚甲基四胺(HA)为固化催化剂,对GAP/TMPTGE/HA固化体系进行了研究。通过拉伸试验、DMA试验,研究了固化参数R和固化时间对GAP/TMPTGE胶片力学性能的影响,借助非等温DSC法,研究了GAP/TMPTGE/HA体系的固化动力学特征,并通过TG实验对胶片热性能进行了表征。结果表明,随着固化参数R的增大,胶片的断裂伸长率先增加后降低,拉伸强度不断增大;R=3.0时,胶片断裂伸长率达到最大值98%,此时拉伸强度为0.67 MPa,玻璃化转变温度为-34.8℃;胶片热分解分为2个阶段,对应的分解峰温分别为250℃和350℃。     

微流量测量方法及其技术的发展

归纳了近五年来基于MEMS技术的微流量传感器结构及性能参数。根据国际上热门的研究方法推断微流量测量技术可能的发展方向与研究趋势,即集成两种或两种以上的测量方法,实现优势互补,提高测量精度或扩大量程比。最后基于现有的技术基础,提出了融合科氏效应与差压效应的微流量测量方法,阐述了传感器的工作原理与理论基础,并对其可行性进行了分析与论证。     

PBT弹性体力学性能及低温脆性研究

采用一步法制备了热固性3,3-双(叠氮甲基)环氧丁烷-四氢呋喃共聚醚(PBT)弹性体,并对其氢键结构、应力-应变关系和动态力学性能及低温脆性进行了研究。结果表明,合成的PBT弹性体拉伸强度和断裂伸长率在DEG羟基含量为35%、R=0.97时,可达2.51 MPa和1 274%,玻璃化温度为-34.5℃。高DEG含量的PBT弹性体脆化参数较低,与常温力学性能变化规律相反。因此,引入低温脆化参数,对PBT弹性体的性能优化具有积极意义。     

光纤陀螺仪中尖峰脉冲引起漂移 的误差分析及其抑制

首次分析了光纤陀螺仪探测器输出信号中频率固定的尖峰脉冲对光纤陀螺 仪零偏漂移的影响机理,给出了尖峰脉冲影响光纤陀螺仪零偏漂移的误差模型;根据干 涉式数字闭环光纤陀螺仪探测器输出信号的特点,提出了一种基于高速集成模拟开关的 时域选通尖峰脉冲抑制具体实现方法,实验验证了尖峰脉冲引起的零偏漂移大小和理论 分析接近,表明了误差模型的正确性,同时表明该方法能够有效降低尖峰脉冲引起的光 纤陀螺仪零偏漂移。