基于神经网络的飞机主要参数估算方法

根据飞机设计要求来选择主要参数往往涉及许多不确定的因素。本文基于多层神经网络计算模型，提出了一种新的飞机主要参数的估算方法，并给出了实现这种方法的详细步骤。将该方法应用于喷气支线飞机和喷气公务机主要参数的估算，测试结果表明估算误差均在10％之内。     

紧凑热交换器优化设计

对各种传热表面的板翅式紧凑热交换器进行了优化设计计算，建立了通用优化程序系统。此程序既适用于一般地面热交换器，也适用于飞机空调中的热交换器。与传统的设计计算相比较，优化设计的效果很好。热交换优化后，肋片的形状变得更加合理，芯体传热表面更加紧。通过各种肋片的计算得出，条状肋片为板翅式肋片中的最佳者。     

三相谐振直流环节逆变器的控制策略

本文针对三相谐振直流环节逆变器提出了三种电流调节方案,并对这三种调节方案进行了分析比较。电流调节△调制方案是零滞环的,它使得三相电流总是流向正确的方向,具有良好的动态特性,但谐波特性较差;相邻模态电流调制方案使逆变器在相邻的开关模态或零开关模态之间进行切换,谐波特性很好,动态特性不够好,而滞环控制电流调制器根据逆变器的实际情况选择开关模态(包括零模态),具有良好的动态特性和谐波特性,适用于三相谐振直流环节逆变器。文中给出了三种方案下的仿真波形,仿真结果的比较也于文后给出。     

着舰导引中的H∞飞行/推力综合控制设计

以提高低动压着舰时动态跟踪及抑制舰尾气流扰动的性能为期望 ,基于线性矩阵不等式 (LMI)的 H∞ 控制理论 ,提出了保持由地速构成的迎角 αd 恒定的 H∞ 飞行 /推力综合控制增广模型结构。使飞机在接近舰尾处于雷达导引系统关闭的关键时刻 ,该系统仍有姿态保持及抑制气流扰动的优良性能 ,从而改变了传统设计需由导引系统纠正气流扰动而引起的轨迹偏离。基于工程应用 ,文中提出了 H∞ 控制器的降阶方法 ,进行了离散化实时仿真验证。仿真表明 ,本文开发的系统能够很好地满足设计要求     

氢氧爆轰直接起始的射流点火方法研究

为探讨氢氧爆轰驱动激波风洞中的高氢混合比氢氧混合气直接爆轰的点火方法，对射流点火管的点火能力进行实验研究发现，点火管长度是决定射流点火能力的关键因素，射流点火能力随点火管长度的增加而增强。点火管与爆轰管之间无隔膜，结构简单，操作方便。同时观察了点火管中增添孔板对射流点火能力的影响，发现障碍物对射流点火能力具有减弱作用。     

Advanced Development of ESG Strapdown Navigation Systems

The fundamental problem of inertial navigation, double integration of acceleration to obtain position, is defined and discussed. Mechanizations of both space-stable and local-vertical platform systems are exhibited. The synthesis problem for an electrically suspended gyro (ESG) strapdown system is defined and discussed: readout, readout errors due to vehicle motion, synchronization of readout with system computer, alignment, correction and calibration for mass unbalance drift, and digital mechanization. Alignment, calibration, and acceleration measurement are also discussed. Sources of error involved in the electronic gimbaling including those peculiar to strapdown configuration are discussed and compared to mechanically gimbaled systems. Advanced developments required in the component and systems areas are listed, and it is shown that such development will lead to reduced complexity, higher accuracy, and increased reliability and utility for inertial systems.     

CAPP系统中特征造型描述法的应用

本文结合专为哈尔滨制氧机厂开发的实用型CAPP系统，对CAPP系统的研制进行了探索性的研究，该系统以Windows作为开发平台，在基于零件特征造型建模的基础上，运用面向对象编程技术完成了一个交互式信息输入子系统，实现了回转体零件CAPP系统的信息输入，这里主要介绍零件特征信息模型的建立与特征信息的数据结构。     

内喷管间隙宽度对线性塞式喷管性能的影响

为了了解内喷管间隙宽度对线性塞式喷管性能的影响，提出了对应着同一个内喷管的三种不同间隙宽度的塞锥。采用数值模拟的方法，得到了不同间隙宽度的线性塞式喷管在不同工况下的流场和性能。比较了不同间隙宽度对线性塞式喷管性能的影响，结果表明：增加内喷管间隙会增大线性塞式喷管的面积比和设计压比；内喷管间隙变宽，塞锥表面的压强下降，塞式喷管的性能下降，间隙宽度增大一倍，塞式喷管性能下降1％～3％。另外在计算过程中发现，内喷管的性能是整个线性塞式喷管性能的主要组成部分，占了整个塞式喷管性能的三分之二以上。     

How we will go to Mars

This article studies the efficiency of ejecting waste generated by the life support system (LSS) of a manned spacecraft to reduce initial mass on low earth orbit. The spacecraft is used for a long-duration interplanetary mission and is equipped with either a chemical or a nuclear-thermal propulsion system. For this study we simulate an optimal control problem for a given spacecraft maneuver. An impulsive approximation of the optimal interplanetary spacecraft trajectory is assumed, which allows us to reduce the general optimal control problem to hierarchic structure of 'outer' and 'inner' subproblems. This structure is analyzed using the Pontryagin's Maximum principle. Numerical results, illustrating the efficiency of waste ejection are shown for typical Earth-Mars transfer trajectories. This results confirm in theory that using a waste ejection system makes an early manned Mars mission possible without having to design and build new, advanced biological LSS.     

Surface characteristics of spacecraft components affect the aggregation of microorganisms and may lead to different survival rates of bacteria on Mars landers

Layers of dormant endospores of Bacillus subtilis HA101 were applied to eight different spacecraft materials and exposed to martian conditions of low pressure (8.5 mbar), low temperature (-10 degrees C), and high CO(2) gas composition and irradiated with a Mars-normal ultraviolet (UV-visible- near-infrared spectrum. Bacterial layers were exposed to either 1 min or 1 h of Mars-normal UV irradiation, which simulated clear-sky conditions on equatorial Mars (0.1 tau). When exposed to 1 min of Mars UV irradiation, the numbers of viable endospores of B. subtilis were reduced three to four orders of magnitude for two brands of aluminum (Al), stainless steel, chemfilm-treated Al, clear-anodized Al, and black-anodized Al coupons. In contrast, bacterial survival was reduced only one to two orders of magnitude for endospores on the non-metal materials astroquartz and graphite composite when bacterial endospores were exposed to 1 min of Mars UV irradiation. When bacterial monolayers were exposed to 1 h of Mars UV irradiation, no viable bacteria were recovered from the six metal coupons listed above. In contrast, bacterial survival was reduced only two to three orders of magnitude for spore layers on astroquartz and graphite composite exposed to 1 h of Mars UV irradiation. Scanning electron microscopy images of the bacterial monolayers on all eight spacecraft materials revealed that endospores of B. subtilis formed large aggregates of multilayered spores on astroquartz and graphite composite, but not on the other six spacecraft materials. It is likely that the formation of multilayered aggregates of endospores on astroquartz and graphite composite is responsible for the enhanced survival of bacterial cells on these materials.