叶片反扭对跨声速大涵道比风扇性能的影响

使用基于流固耦合算法的叶片反扭程序,考虑了非定常气动力对叶片变形的非线性作用,研究了叶片反扭对跨声速大涵道比风扇性能的影响.以冷态叶型为起点,先计算离心力作用下的叶片变形,在此基础上使用流固耦合程序获得非定常气动力作用下的变形.考察了3个转速下叶片的动态变形对大涵道比风扇气动性能的影响.结果表明:在跨声速工况下,叶片表面激波位置的变化对叶片反扭角有很大作用,在考察的转速范围内,堵塞点使用设计叶型计算的流量大于动态叶型下的流量,数值达7%,将导致发动机起飞推力小于预测值.结果表明在大涵道比风扇设计阶段,预测气动性能使用准确叶型的重要性.      

数字示波器在尖峰干扰脉冲强度测量中的应用

运用数字示波器瞬态捕获能力及面积测量功能，快速、准确、不遗漏地测量电子设备的尖峰干扰信号（脉冲信号），用公式将脉冲强度单位换算为脉冲频谱密度单位。     

球形粒子在流体中的跟随性

本文从Maxey和Riley的粒子运动基本方程出发,得到了球形固体粒子在相对流动雷诺数很小情形下的分析解。讨论了粒子跟随性对外力、初始条件和流场性质的依赖关系;对均匀湍流场,分析了不同密度比和扰动频率对跟随性的影响     

断裂韧性K_(1C)和断裂门槛值ΔK_(th)可靠性测定方法

采用定量方程随机化方法 ,建立了断裂p JR Δa曲线方程 ,断裂p JR Δa曲线与钝化线的交点即为试验测定具有可靠度p的J积分临界值 (J1C) p值 ,根据断裂力学测试原理 ,由试验测定 (J1C) p 值可转化出断裂韧性 (K1C) p 值 ;还建立了断裂门槛ΔKth值的可靠性测定方法 ,并对试验数据进行了统计分析处理 ,得到了一些具有重要应用价值的结果和数据 .研究发现 :断裂门槛值ΔKth服从正态分布     

Optimum parameter matching obtained by experiments for coring drilling into lunar simulant

This paper performs a series of ground experiments (on the Earth) to obtain optimum parameter matching for a future core drill on the Moon. Three common stages, I, II, III, are recognized with respect to the cut per revolution (CPR), which is defined as the ratio between the feeding speed and the rotating speed. The optimum matching between the feeding speed and the rotating speed for drills locates at the boundary position between Stage II and Stage III, where the coring rate saturates and the weight on the bit and the driving torque are still low. Further data analysis of the ground experiments reveals that the optimum matching signifies a proportional relation between the maximum conveying rate (MCR) by the groove of the auger and its rotating speed. The kinetic analysis in an ideal condition without gravity, the friction from the auger groove and the pressure at the bit confirm a similar proportion. The correlation between the proportions needs further study to determine whether the optimum matching obtained on the ground can be directly applied to future drills on the Moon.     

某锅炉钢结构角钢对扣箱型结构的焊接

某锅炉钢结构项目电梯井立柱采用了角钢对扣的箱型结构,此种箱形结构截面小,焊缝布置不对称,且焊缝长度较大,坡口切割变形、焊接变形难以控制,我们通过自制工装改进制作工艺解决了此类问题,满足该项目的验收要求。     

在企业深化改革中开创社会化计量测试新局面

通过大量的事实，阐述了在企业不断深化改革过程中，开创社会化计量测试的基础，条件及基本做法。     

中间件技术的研究及应用

本文在分析了分布式应用系统体系结构发展变化的基础上．阐述了中间件的概念、功能和在可重用、多异构数据源应用系统的作用，对ODBC、BDE／IDAPIT、0LEDB／ADO和JDBC等分布式数据库中间件；CGI、lSAPI／NSAPI、ASP、JSP等中间件进行了分析比较，并给出了中间件技术在教务管理信息系统的应用实例。     

Angle estimation for two unresolved targets with monopulse radar

Most present-day radar systems use monopulse techniques to extract angular measurements of sunbeam accuracy. The familiar "monopulse ratio" is a very effective means to derive the angle of a single target within a radar beam. For the simultaneous estimation of the angles of two closely-spaced targets, a modification on the monopulse ratio was derived in (Blair and Pearce, 2001), while (Sinha et al., 2002) presented a maximum likelihood (ML) technique via numerical search. In this paper it is shown that the ML solution can in fact be found explicitly, and the numerical search of ((Sinha et al., 2002) is unnecessary. However, the ML solution requires the signal to noise ratio (SNR) for each target to be known, and hence we generalize it so it requires only the relative SNR. Several versions of expectation maximization (EM) joint angle estimators are also derived, these differing in the degree to which prior information on SNR and on beam pattern are assumed. The performances of the different direction-of-arrival (DOA) estimators for unresolved targets are studied via Monte Carlo, and it is found that most have similar performance: this is remarkable since the use of prior information (SNR, relative SNR, beam pattern) varies widely between them. There is, however, considerable performance variability as a function of the two targets' off-boresight angles. A simple combined technique that fuses the results from different approaches is thus proposed, and it performs well uniformly.