SBS改性再生型木塑复合材料及其耐水性能

为了充分利用城市固体废弃物中的各项资源，本项工作将固体废弃物中的高密度聚乙烯（HDPE）回收后与废弃的木纤维、苯乙烯-丁二烯-苯乙烯（SBS）进行复合，成功地制备出SBS／再生型木塑复合材料，并进行了力学性能测试和水煮试验。结果表明，SBS的加入使木塑复合材料的冲击韧性得到显著改善，同时，复合材料的弯曲强度和弯曲模量没有明显的影响，表明SBS可以作为木塑复合材料的增韧剂。SBS／木塑复合材料经过8周、60℃的水煮后，复合材料的吸水率和厚度膨胀率均有所增加，弯曲模量和冲击韧性分别平均下降14．4％、10．8％。水煮试验初期复合材料的弯曲强度逐渐降低，然后又逐渐增大，第8周后弯曲强度增加的幅度约10％。木塑复合材料的冲击破坏模式以界面脱粘为主，而加入SBS后，复合材料的破坏以纤维断裂和基体断裂为主。     

Stochastic Dynamic System Suboptimal Control with Uncertain Parameters

The control of a linear system with random coefficients is studied here. The cost function is of a quadratic form and the random coefficients are assumed to be partially observable by the controller. By means of the stochastic Bellman equation, the optimal control of stochastic dynamic models with partially observable coefficients is derived. The optimal control is shown to be a linear function of the observable states and a nonlinear function of random parameters. The theory is applied to an optimal control design of an aircraft landing in wind gust.     

Parallel resonant converter with LLC-type commutation

It is shown that by using a proper transformation of state variables, the third-order system of the parallel resonant converter (PRC) with LLC-type commutation can be analyzed by means of a two-dimensional state-plane diagram. A set of characteristic curves which can be used for the converter design is derived from the analysis. It is shown from these curves that the converter possesses more desirable features than the conventional PRC     

Investigations of Stability & Dynamic Performances of a Current-Injected Regulator

The stability and dynamic performances of a buck/boost regulator employing a current-injected control are examined. Small-signal models for the power state, the multiloop error processor, and the duty-cycle pulse modulator are developed. The error-processor model which incorporates the current-injected loop, the dc loop, and the compensation network permits evaluation of the effects of each individual control loop and their combined efforts toward shaping the performance characteristics of the closed-loop system. Comparisons are made between this modeling approach and earlier approaches. Some important yet subtle dissimilarities are discussed. This model predicts the constant-frequency 50-percent duty-cycle instability which is inherent to the current-injected control.     

Multiposition alignment of strapdown inertial navigation system

The authors demonstrate that the stationary alignment of strapdown inertial navigation system (SDINS) can be improved by employing the multiposition/technique. Using an observability analysis, it is shown that an optimal two-position alignment not only satisfies complete observability conditions but also minimizes alignment errors. This is done by analytic rank testing of the stripped observability matrix and numerical calculation of the error covariance. It is also shown that an optimal three-position alignment accelerates the convergence of the alignment error compared with two-position alignment     

Improved Switching Converter Model Using Discrete and Averaging Techniques

The nonlinear modeling and analysis of dc-dc converters has been done by averaging and discrete-sampling techniques. The averaging technique is simple, but inaccurate, as the modulation frequencies approach the theoretical limit of one-half the switching frequency. The discrete technique is accurate even at high frequencies, but is very complex and cumbersome. An improved model is developed by combining the aforementioned techniques. This new model is easy to implement in circuit and state variable forms and is accurate to the theoretical limit.     

Nondestructive Characterization of RBSOA of High-Power Bipolar Transistors

Reverse-bias safe operating area (RBSOA) of high-power Darlington transistors is characterized using a 120 A/1000 V nondestructive reverse-bias second breakdown tester designed and fabricated at Virginia Polytechnic Institute and State University. Elaborate RBSOA characteristics are generated with different forward/reverse base drives and collector current levels. The effects of elevated case temperature and second-base drive on RBSOA of four-terminal Darlington devices are also discussed.     

Comparison of half-bridge off-line, ZCS-QRC and ZVS-MRC

The performance of the half-bridge (HB) zero-current-switched (ZCS) quasi-resonant converter (QRC) and zero-voltage-switched (ZVS) multiresonant converter (MRC) is compared with respect to their efficiency, input voltage range, semiconductor stresses, power density, and reliability. The efficiency of the HB ZVS-MRC at a given nominal input is shown to be highly dependent on the range of the input voltage, and it suffers when the converter has to be designed to cover a wide range. However, this is not the case for the HB ZCS-QRC. Experimental versions of the HB ZCS-QRC and HB ZVS-MRC were designed for the input voltage range from 150 to 350 V and a maximum output power of 100 W, under the same constraints, to facilitate their comparison     

Analysis and Design of Series Resonant Converter by State-Plane Diagram

Analysis based on the state-plane diagram is given for series resonant converters operating in the frequency range 0.5 ? fs/fo ? 1.0. When the voltages and currents in the converter are normalized, design parameters take on special geometric meanings in the normalized state diagram. Examples of converter design using graphical methods are given for the cases of ? and ? control. Control characteristics of the converter operating in the continuous conduction mode are derived. The concept of the energy reflection coefficient is introduced as a measure of power transfer efficiency in the converter design.     

Extensions of the Discrete-Average Models for Converter Power Stages

An improved power converter model is developed by combining the average and discrete modeling techniques. The parameter determination of the proposed discrete-average model is shown to be dependent on the type of duty cycle control law and the nature of the error processor used in the feedback loop. Furthermore, the paper pinpoints deficiencies of the conventional loop gain measurement technique which is widely used in industries.