高背压等离子点火器及其液体燃料点火特性实验研究

航天应用的液体火箭发动机及燃烧型加热器燃烧室室压高、燃料流量大、温度低、有重复启动需求，实现安全可靠点火的难度较大。针对这些需求，研究了一种采用高背压设计的电弧等离子体点火器。实验研究了Ar，N₂气体工质在高进气压力下的伏安特性，发现N₂在宽压力范围内适用于点火。发射光谱分析表明，在高达数MPa的进气压力下，Ar，N₂等离子体射流电子密度符合局部热力学平衡判据（LTE判据），点火能量集中。N₂等离子体整体温度低于Ar，但阳极喷口附近温度高于Ar，N₂等离子体射流火焰长，卷吸沿程空气造成射流平均温度偏低，但有助于低温液体推进剂的蒸发混合和强化点火。等离子体射流引起了臭氧和氮氧化物的形成，具有促进点火和化学反应的作用。背压提高引起电源输出电压升高，提高供气压力和电流，有助于点火器在高背压环境中稳定电压。燃烧型空气加热器燃烧室的点火实验发现，采用N₂等离子体喷注面中心点火，可以在短时间内完成酒精-空气和酒精-液氧-空气的点火，最高燃烧室室压接近5MPa时，点火器仍能稳定工作，多次使用电极烧蚀不明显，在液体火箭发动机的重复可靠点火方面具有很好的应用前景。     

Topology optimization in lightweight design of a 3D-printed flapping-wing micro aerial vehicle

Topology optimization is an effective method to obtain a lightweight structure that meets the requirements of structural strength. Whether the optimization results meet the actual needs mainly depends on the accuracy of the material properties and the boundary conditions, especially for a tiny Flapping-wing Micro Aerial Vehicle (FMAV) transmission system manufactured by 3D printing. In this paper, experimental and numerical computation efforts were undertaken to gain a reliable topology optimization method for the bottom of the transmission system. First, the constitutive behavior of the ultraviolet (UV) curable resin used in fabrication was evaluated. Second, a numerical computation model describing further verified via experiments. Topology optimization modeling considering nonlinear factors, e.g. contact, friction and collision, was presented, and the optimization results were verified by both dynamic simulation and experiments. Finally, detailed discussions on different load cases and constraints were presented to clarify their effect on the optimization. Our methods and results presented in this paper may shed light on the lightweight design of a FMAV.     

过氧化氢/紫外线/臭氧氧化技术处理肼类污水的应用

采用放大试验规模（处理量1 m³/h）的H₂O₂（过氧化氢）/UV（紫外线）/O₃（臭氧）氧化技术处理肼类推进剂污水，在30.0±1.6 ℃，pH=9.0±0.2的条件下，研究肼类的过氧化氢增强光解臭氧化降解。对比不同氧化技术的协同效应以及对污水降解的影响，重点考察过氧化氢、紫外线、臭氧和初始浓度等工艺参数对降解效果的影响，对氧化技术的应用进行了优化。研究结果表明：该技术可使COD去除率提高27.66%，肼类的降解速率随着过氧化氢投加量、紫外线辐射强度、O₃投加速率和水质地提高而升高，随着初始质量浓度的提高而下降。在最佳工艺下，处理5 000 mg/L质量浓度的废水，处理60 min时，COD去除率分别为98.62%（偏二甲肼）、99.17%（甲基肼）、99.94%（肼）和93.25%（单推-3）。     

双模块下颌式内转进气道/圆锥前体一体化布局研究

为实现三维内转进气道的内收缩流场与圆锥前体的外压缩流场的良好匹配，提出了一种双模块下颌式内转进气道/圆锥前体(Double-modules Chin Inward-turning Inlet and Conical Forebody，DCII/CF)一体化设计方法，获得一种新颖的双发并置、侧向安装的DCII/CF一体化布局。针对该布局形式，开展了DCII/CF一体化构型与传统的单模块内转进气道/圆锥前体(Single-module Inward-turning Inlet and Conical Forebody，SII/CF)一体化构型的数值对比研究。结果表明：DCII/CF一体化布局不仅为内转进气道提供了优秀的前体附面层排移效果，还有效避免了传统SII/CF布局中前体附面层与进气道内部流场之间的相互干扰。在Ma∞=6.0设计状态，DCII/CF一体化布局的进气道总压恢复系数相较传统的SII/CF布局有了显著提高，从0.403提高至0.482；但由于前体附面层的排移，该布局的捕获流量略有降低， SII/CF的流量系数为0.956，该布局则为0.917。而在非设计状态，该布局形式同样具备较好的总压恢复性能，在Ma∞=5.0与Ma∞=4.0的总压恢复系数分别达到了0.586和0.682，明显高于SII/CF的总压恢复系数0.507和0.619。     

PBT弹性体微相分离及对其力学性能的影响研究

为了获得微相分离对宽温PBT叠氮聚醚弹性体力学性能的影响规律,用红外光谱分析法(FT-IR)和动态热力学分析法(DMA)研究了PBT叠氮聚醚弹性体产生微相分离的机理和影响因素。用调节硬段含量、交联参数的方法调控其微相分离,控制适当的微相分离程度可显著改善推进剂的力学性能。研究结果表明:在二元醇扩链的弹性体体系中,当硬段含量约为15%时,弹性体发生相对最大比例的微相分离,体现出较佳的综合力学性能。通过微相分离的调控可获得宽温范围内综合力学性能较好的叠氮聚醚推进剂用粘合剂基体材料。     

虚拟环境系统中复杂模型的建立--3D资源在快速开发虚拟环境系统中的应用

对利用3D资源在快速开发虚拟环境系统中的方法进行了研究。在开发虚拟环境系统的过程中，复杂模型的建立是必不可少的，仅仅利用OpenGL函数编程来实现仿真是很困难的，针对该问题提出了利用3D资源进行3D文件读取和转换的两种方案，分析了虚拟环境中复杂模型的建立以及处理的基本方法，并对数控车床的仿真进行了详细介绍。     

VKM—5型立式捏合机研制与应用

介绍自行研制的VKM—5型立式捏合机的构造及工作原理,详述了该机采用液压传动和气动元件进行位置检测以及气、电、液安全联锁的特点,并说明与卧式捏合机对比试验情况。     

多孔高氯酸铵的制备及其对固体推进剂燃速的影响

介绍美国和台湾用对流炉和沸腾床制备多孔高氯酸铵(PAP)及包覆法。同时介绍了用PAP部分取代HTPB体系推进剂中的AP和全部取代双基推进剂中的超细AP的燃烧性能研究。结果表明,用包覆的PAP取代超细AP是提高燃速的较好途径。     

Global Response of Martian Plasma Environment to an Interplanetary Structure: From Ena and Plasma Observations at Mars

As a part of the global plasma environment study of Mars and its response to the solar wind, we have analyzed a peculiar case of the subsolar energetic neutral atom (ENA) jet observed on June 7, 2004 by the Neutral Particle Detector (NPD) on board the Mars Express satellite. The “subsolar ENA jet” is generated by the interaction between the solar wind and the Martian exosphere, and is one of the most intense sources of ENA flux observed in the vicinity of Mars. On June 7, 2004 (orbit 485 of Mars Express), the NPD observed a very intense subsolar ENA jet, which then abruptly decreased within ∼10 sec followed by quasi-periodic (∼1 min) flux variations. Simultaneously, the plasma sensors detected a solar wind structure, which was most likely an interplanetary shock surface. The abrupt decrease of the ENA flux and the quasi-periodic flux variations can be understood in the framework of the global response of the Martian plasma obstacle to the interplanetary shock. The generation region of the subsolar ENA jet was pushed towards the planet by the interplanetary shock; and therefore, Mars Express went out of the ENA jet region. Associated global vibrations of the Martian plasma obstacle may have been the cause of the quasi-periodic flux variations of the ENA flux at the spacecraft location.     

Tunnel/predictor display with two-axis control coordination and simplification

A longitudinal-lateral control coordination and simplification concept is considered for a tunnel/predictor display, which presents the command flight path and a specified future aircraft position in a 3-dimensional format to the pilot, for improving flight path control. A basic element of the proposed concept is the generation of common longitudinal-lateral transfer characteristics of the predictor-aircraft system for the crossover frequency region. Control coordination is supported by a dynamics similarity between the longitudinal and the lateral response characteristics of the predictor position in closed-loop pilot control actions. The control coordination and simplification concept is considered to support the pilot in manual flight path control, directed at an enhancement of his control performance and at a reduction of his workload. Results from pilot-in-the-loop simulation experiments support the theoretical findings and show the effectiveness of the proposed predictor concept with control coordination.