A challenge to the highest balloon altitude

Development of a balloon to fly at higher altitudes is one of the most attractive challenges for scientific balloon technologies. After reaching the highest balloon altitude of 53.0 km using the 3.4 μm film in 2002, a thinner balloon film with a thickness of 2.8 μm was developed. A 5000 m³ balloon made with this film was launched successfully in 2004. However, three 60,000 m³ balloons with the same film launched in 2005, 2006, and 2007, failed during ascent. The mechanical properties of the 2.8 μm film were investigated intensively to look for degradation of the ultimate strength and its elongation as compared to the other thicker balloon films. The requirement of the balloon film was also studied using an empirical and a physical model assuming an axis-symmetrical balloon shape and the static pressure. It was found that the film was strong enough. A stress due to the dynamic pressure by the wind shear is considered as the possible reason for the unsuccessful flights. A 80,000 m³ balloon with cap films covering 9 m from the balloon top will be launch in 2011 to test the appropriateness of this reinforcement.     

Development overview of the revised NASA Ultra Long Duration Balloon

The desire for longer duration stratospheric flights at constant float altitudes for heavy payloads has been the focus of the development of the National Aeronautics and Space Administration’s (NASA) Ultra Long Duration Balloon (ULDB) effort. Recent efforts have focused on ground testing and analysis to understand the previously observed issue of balloon deployment. A revised approach to the pumpkin balloon design has been tested through ground testing of model balloons and through two test flights. The design approach does not require foreshortening, and will significantly reduce the balloon handling during manufacture reducing the chances of inducing damage to the envelope. Successful ground testing of model balloons lead to the fabrication and test flight of a ∼176,000 m³ (∼6.2 MCF – Million Cubic Foot) balloon. Pre-flight analytical predictions predicted that the proposed flight balloon design to be stable and should fully deploy. This paper provides an overview of this first test flight of the revised Ultra Long Duration Balloon design which was a short domestic test flight from Ft. Sumner, NM, USA. This balloon fully deployed, but developed a leak under pressurization. After an extensive investigation to the cause of the leak, a second test flight balloon was fabricated. This ∼176,000 m³ (∼6.2 MCF) balloon was flown from Kiruna, Sweden in June of 2006. Flight results for both test flights, including flight performance are presented.     

Temperature variability in the tropical mesosphere during the northern hemisphere winter

Temperature observations at 20–90 km height and 5°N–15°N during the period of December 1992–March 1993 from the WINDII and MLS experiments on the UARS satellite are analysed together with MF radar winds and UKMO assimilated fields of temperature and zonal and meridional winds. The correlation between the different datasets at the tropics and zonal mean wind data at mid latitudes is examined for period February–March 1993, when series of stratospheric warming events were observed at middle and high latitudes. Wavelet analysis is applied to investigate coupling between stationary and travelling planetary waves in the stratosphere and the upper mesosphere. Planetary waves m = 1 with periods of 4–7 days, 8–12 days and 13–18 days are found to dominate the period. Westward 7- and 16–18 day waves at the tropics appear enhanced by stationary planetary waves during sudden stratospheric warming events.     

Evolution of scientific ballooning and its impact on astrophysics research

As we celebrate the centennial year of the discovery of cosmic rays on a manned balloon, it seems appropriate to reflect on the evolution of ballooning and its scientific impact. Balloons have been used for scientific research since they were invented in France more than 200 years ago. Ballooning was revolutionized in 1950 with the introduction of the so-called natural shape balloon with integral load tapes. This basic design has been used with more or less continuously improved materials for scientific balloon flights for more than a half century, including long-duration balloon (LDB) flights around Antarctica for the past two decades. The U.S. National Aeronautics and Space Administration (NASA) is currently developing the next generation super-pressure balloon that would enable extended duration missions above 99.5% of the Earth’s atmosphere at any latitude. The Astro2010 Decadal Survey report supports super-pressure balloon development and the giant step forward it offers with ultra-long-duration balloon (ULDB) flights at constant altitudes for about 100 days.     

Simultaneous observations of Pc 1 micropulsation activity and stratospheric electrodynamic perturbations on 27 January 2003

The 2nd Polar Patrol Balloon campaign (2nd-PPB) was carried out at Syowa Station in Antarctica during 2002–2003. Identical stratospheric balloon payloads were launched as close together in time as allowed by weather conditions to constitute a cluster of balloons during their flights. A very pronounced negative ion conductivity enhancement was observed at 32 km in the stratosphere below the auroral zone on 27 January 2003 from 1500 to 2200 UT. During this event, the conductivity doubled for an interval of about 7 h. This perturbation was associated with an extensive Pc 1 or Pi 1 wave event that was observed by several Antarctic ground stations, balloon PPB 10, and the Polar spacecraft. No appreciable X-ray precipitation was observed in association with this event, which would point to >60 Mev proton precipitation as a possible magnetosphere–stratosphere coupling mechanism responsible for the conductivity enhancement. Such precipitation is consistent with the wave data. During the latter half of the event, E_z was briefly positive. There was a tropospheric Southern Ocean storm system underneath the balloon during this interval. If the event was associated with this storm system and not energetic proton precipitation, the observations imply an electrified Southern Ocean storm and major perturbations in stratospheric conductivity driven by a tropospheric disturbance. This event represents a poorly understood source for global circuit current. Precipitating energetic proton data from Akebono and NOAA POES spacecraft show significant >16 MeV precipitation was occurring at the location of PPB 8 but not PPB 10, suggesting that proton precipitation was, in fact, the responsible coupling mechanism.     

Stratospheric flights with large polyethylene baloons from equatorial latitudes

Starting with average 50% success for stratospheric balloon flights during 1959–1969 and attaining 100% success during 1972–1973, the success record dropped to 50% during 1974–1979. Through a critical analysis of 59 flights made from Hyderabad and 21 flights made from other equatorial bases, revised design criteria were proposed for balloons to be flown from equatorial latitudes, which were accepted by M/s Winzen International, Inc. (WII), U.S.A. and have again raised the success record to 93% for 15 flights made since April 1980. A revised analysis for 71 flights made from 1965 to 1984 has been presented. Stratospheric circulation over Hyderabad indicating predominance of easterlies with mesospheric westerlies descending occasionally into stratosphere has been discussed.     

Mesospheric doppler wind measurements from Aura Microwave Limb Sounder (MLS)

This paper describes a microwave limb technique for measuring Doppler wind in the Earth’s mesosphere. The research algorithm has been applied to Aura Microwave Limb Sounder (MLS) 118.75 GHz measurements where the O₂ Zeeman lines are resolved by a digital autocorrelation spectrometer. A precision of ∼17 m/s for the line-of-sight (LOS) wind is achieved at 80–92 km, which corresponds to radiometric noise during 1/6 s integration time. The LOS winds from Aura MLS are mostly in the meridional direction at low- and mid-latitudes with vertical resolution of ∼8 km. This microwave Doppler technique has potential to obtain useful winds down to ∼40 km of the Earth’s atmosphere if measurements from other MLS frequencies (near H₂O, O₃, and CO lines) are used. Initial analyses show that the MLS winds from the 118.75 GHz measurements agree well with the TIDI (Thermosphere Ionosphere Mesosphere Energetics and Dynamics Doppler Interferometer) winds for the perturbations induced by a strong quasi 2-day wave (QTDW) in January 2005. Time series of MLS winds reveal many interesting climatological and planetary wave features, including the diurnal, semidiurnal tides, and the QTDW. Interactions between the tides and the QTDW are clearly evident, indicating possible large tidal structural changes after the QTDW events dissipate.     

A balloon-borne sun-tracking multichannel photometer for atmospheric aerosol measurements

A balloon borne multichannel photometer for measurement of atmospheric scattering in the near ultraviolet and the visible wavelength regions has been developed at the Physical Research Laboratory, Ahmedabad for study of the size distribution and number density of aerosols at tropospheric and lower stratospheric altitudes. The instrumentation involves tracking the sun in elevation and scanning in azimuth. The payload was recently flown on a 100 kg. balloon from the Hyderabad Balloon Facility on 18 April 1984. The balloon reached a float altitude of 35 km and good quality data has been obtained from an altitude of 6 km upto float altitude. Data analysis is still in progress. The present paper details the instrument design and presents a few illustrations of the instrument performance from this flight.     

Magnetospheric application of high-altitude long-duration balloon technology: Daylight auroral observations

Daylight auroral imaging is a proposed application of the NASA high-altitude long-duration balloon technology. This paper discusses the theoretical background of this application and test observations, for proof of the feasibility. It is demonstrated that nitrogen auroral emissions in the near-infrared band are detectable at altitudes of 35–40 km and above using a near-infrared InGaAs camera. The purpose of such observations is to identify auroral small-scale structures that are manifestations of auroral particle accelerations and the solar wind – magnetosphere – ionosphere interaction. Use of this new approach will enable studies of the dayside aurora, low-latitude aurora, and storm-time and substorm-time auroral conjugacy.     

Semi-empirical model of middle atmosphere wind from the ground to the lower thermosphere

During recent years, special attention has been paid to understanding the background circulation of the middle atmosphere. Particularly in the mesosphere/lower thermosphere (MLT) region, this has involved including data from a range of new radar measurements. It has also involved the comparison of existing empirical middle atmosphere wind models, such as CIRA-86 and HWM-93 to the new data. This has led to the construction of empirical models of MLT winds such as the Global Empirical Wind Model (GEWM). Further investigations are aimed at the construction of new empirical and semi-empirical wind models of the entire middle atmosphere including these new experimental results. The results of a new wind climatology (0–100 km) are presented here, based upon the GEWM, a reanalysis of stratospheric data, and a numerical model which is used to fill the gap between data from the stratospheric and MLT regions.     

The radiation controlled balloon (RACOON)

The RACOON concept permits the flight of large, low-cost polyethylene balloons for several weeks at stratospheric altitudes without ballast. The theory of operations is described. The RACOON balloon ascends each morning and descends at night. This movement of 15 to 20 km in altitude provides an ideal platform for vertical soundings and sampling measurements in the stratosphere. Results of a number of globe-circling flights are presented.     

USV test flight by stratospheric balloon: Preliminary mission analysis

The Unmanned Space Vehicle test flights will use a 7 m 1300 kg aircraft. The first three launches will take place at the Italian Space Agency ASI base in Trapani–Milo, Sicily, through a stratospheric balloon that will drop the aircraft at a predefined height. After free fall acceleration to transonic velocities, the parachute deployment will allow a safe splash down in the central Mediterranean Sea. The goal of this article is to show the preliminary analysis results for the first USV flight.We carried out a statistical study for the year 2000–2003, evaluating the typical summer and winter launch windows of the Trapani–Milo base.First, in the center Mediterranean, we define safe recovery areas. They cannot be reached during the balloon ascending phase so, after a sufficiently long floating part able to catch the open sea, the balloon will go down to the release height (24 km). The simulation foresees a 400,000 m³ balloon and 3 valves for the altitude transfer.A safe splash down must occur far enough from the nearest coast: the minimum distance is considered around 25 km. The vehicle should be released at a distance, from the nearest coast, greater than this minimum amount plus the USV model maximum horizontal translation, during its own trajectory from balloon separation to splash down. In this way we define safe release areas for some possible translations.Winter stratospheric winds are less stable. The winter average flight duration is 7 h and it is probably too long for the diurnal recovery requirement and its scheduled procedures.Comparing past stratospheric balloons flights and trajectories computed using measured meteorological data (analysis), with their predictions made using forecast models and soundings, we obtain the standard deviation of the trajectory forecast uncertainty at the balloon–aircraft separation. Two cases are taken into account: predictions made 24 and 6 h before the launch.Assuming a Gaussian latitudinal uncertainty distribution for the prediction 6 h before the launch, we are able to identify the forecast trajectories that have a probability greater than 97% to reach the safe release areas.Simulating the summer windows trajectories for the years from 2000 to 2003 and for the favorable ground wind days, we obtain the number of trajectories with the desired forecast probabilities.     

中纬度地磁暴期间热层垂直风响应机制的模拟

基于TIMEGCM模型,研究了2005年9月10日中纬度地磁暴期间热层(100～650 km)水平风场变化对垂直风的影响.通过连续性方程诊断分析了暴时引起垂直风场变化的机制,结果表明:250 km以上的垂直风场取决于水平风场的变化,而250 km以下的垂直风场由较高高度的垂直风拉动;在地磁暴初相开始时,经向风场相比纬向...     

Balloon-borne,high-altitude gravimetry

Gravity measurements from a high-altitude balloon can verify global and upward-continued gravity models. A gravimeter suspended beneath a balloon is in a dynamic, and largely unpredictable, environment sensing accelerations due to gravity and balloon motions. Independent measurements of balloon motions using inertial navigation data combined with ground tracking data will allow for separation of balloon-induced accelerations from gravitational accelerations. Analysis of these data must estimate: 1) vertical gravimeter accelerations due to motion and gravity, 2) horizontal velocity to estimate the Eötvös effect, and 3) gravimeter position for comparison with gravity models. The first engineering test flight occurred on 11 October 1983, during the seasonal wind reversal and was very successful. Flight duration was approximately seven hours, with two hours of data collected at each of 30 km and 26 km altitudes. The results include gravity estimates, design criteria for future flights and feasibility analysis for vertical gravity profiles during ascent and descent.     

High altitude flights in equatorial regions

A thorough analysis of balloon flights made from Hyderabad, India (Latitude 17°28′N, Longitude 78°35′E), and other equatorial sites has been made. It has been shown that limited success is expected for flights made from equatorial latitudes with balloons made out of natural colour polyethylene film, since the best known balloon film in the world today viz. Winzen Stratofilm is tested for low temperature brittleness only at ?80°C., whereas the tropopause temperatures over equatorial latitudes vary between ?80°C and ?90°C. The success becomes even more critical when flights are made with heavy payloads and larger balloons particularly at night when in the absence of solar radiation the balloon film becomes more susceptible to low temperature brittle failure. It is recommended that in case of capped balloons longer caps should be used to fully cover the inflated protion of the balloon at the higher level equatorial tropopause. It is also advised that the conditions such as wind shears in the tropopause should be critically studied before launching and a day with the tropopause temperature nearer to ?80°C should be chosen. Special care also should be taken while handling the balloon on ground and during launching phase. Properties of Winzen Stratofilm have been critically studied and fresh mandates have been recommended on the basis of limiting values of film stresses which caused balloon failures in the equatorial tropopause. It is also emphasized that the data on such flights is still meagre especially for flights with heavy payloads and larger balloons. It has been also shown that it is safest to use balloons made out of grey coloured film which retains its flexibility with the absorption of solar radiation, the success obtained with such balloons so far being 100%. The drawback, however, is that these balloons cannot be used for night flights. Stratospheric wind regimes over Hyderabad are also discussed with a view to determine the period over which long duration flights can be made. The data available, however, is meagre and it is recommended that more frequent special wind ascents be made to collect adequate statistical data from which reliable conclusions could be drawn through critical analysis.     

Telemetry,telecommand and safety sub-systems for scientific ballooning from Hyderabad

Highly sophisticated balloon-borne scientific payloads have stringent requirement on the telemetry and command system. The development and fabrication of the on-board TT&C package for telemetry, tracking, command, safety and ranging for these experiments is done in-house at the National Balloon Facility (NBF) at Hyderabad. In the last few years, we have made major improvements both in the ground station and the on-board sub-systems, thereby improving the data quality, data handling speed and the general flight control along with aviation safety. The new system has telemetry data rate up to 1 Mbps. A reduction in weight, power and cost of the reengineered on-board integrated package has also lead to the ease of operation during field tests prior to launch and at remote recovery sites. In this paper, we describe the details of the new control package, its flight performance and our plans for portable S-band telemetry and telecommand system to cater to the balloon flights from Antarctic station and long duration balloon flights.     

Horizontal winds in the mesosphere at high latitudes

A total of 146 meteorological rocket flights applying the ‘falling sphere’ technique are used to obtain horizontal winds in the mesosphere at polar latitudes, namely at the Andøya Rocket Range (69°N, 125 flights), at Spitsbergen (78°N, 10 flights), and at Rothera (68°S, 11 January flights only). Nearly all flights took place around noon or midnight, i.e., in the same phase of the semidiurnal tide. Meridional winds at 69°N show a clear diurnal tidal variation which is not observed in the zonal winds. The zonal wind climatology shows a transition from summer to winter conditions with the zero wind line propagating upward from 40 km (end of August) to 80 km (end of September). Zonal winds are smaller at Spitsbergen compared to Andøya which is in line with a common angular velocity at both stations. Meridional winds at noon are of similar magnitude at all three stations and are directed towards the north and south pole, respectively. Horizontal and meridional winds generally agree with empirical models, except for the zonal winds at Antarctica which are similar to the NH, whereas there is a significant SH/NH difference in CIRA-1986.     

基于中国岢岚地区法布里-珀罗干涉仪的风场及行星波观测特征

利用中国岢岚站（38.7°N,111.6°W）法布里-珀罗干涉仪2013年7月至2014年11月的水平风场数据,对87,97,250km风场长期变化和行星波特征进行了研究.通过分析年振荡（AO）和半年振荡（SAO）振幅相位,将午夜风场与HWM07数据对比发现:87km和97km处FPI纬向风变化趋势与HWM07相近,而经向风相位落后于HWM07,从振幅上看,HWM07振幅偏大;250km处风场月变化大,FPI与HWM07差异大,HWM07模式的准确性需进一步考虑太阳活动和行星际磁场的影响.利用Lomb-Scargle功率谱以及最小二乘谐波拟合提取了三个高度的行星波振幅,其特征表明87km和97km处纬向风16日波秋季及冬春季活动强,而6.5日波最强振幅出现在春季和秋季,在中间层顶附近两种行星波活动均较弱;250km处经向行星波活动略强于纬向,经向风不同周期带的行星波最强振幅主要出现在5-9月,与电离层f₀F₂振荡特性的研究结果一致.      

Mid-latitude thermospheric zonal winds during the equinoxes

The diurnal variation of the mid-latitude upper thermosphere zonal winds during equinoxes has been studied using data recently generated from CHAMP measurements from 2002 to 2004 using an iterative algorithm. The wind data was separated into two geomagnetic activity levels, representing high geomagnetic activity level (Ap > 8) and low geomagnetic activity level (Ap ? 8). The data were further separated into two solar flux levels; with F10.7 > 140 for high and F10.7 ? 140 for low. Geomagnetic activity is a correlator just as significant as solar activity. The response of mid-latitude thermospheric zonal winds to increases in geomagnetic disturbances and solar flux is evident. With increase in geomagnetic activity, midday to midnight winds are generally less eastward and generally more westward after the about midnight transitions. The results show that east west transitions generally occurred about midnight hours for all the situations analyzed. The west to east transition occurs from 1400–1500 MLT. Enhanced westward averaged zonal wind speeds going above 150 ms⁻¹ are observed in the north hemisphere mid-latitude about sunrise hours (∼0700–1100 MLT). Nighttime winds in the north hemisphere are in good agreement with previous single station ground observations over Millstone Hill. Improved ground observations and multi satellite observations from space will greatly improve temporal coverage of the Earth’s thermosphere.