Development of a super-pressure balloon with a diamond-shaped net

The essential reason of the lobed-pumpkin shaped super-pressure balloon to withstand against the high pressure is that the local curvature of the balloon film is kept small. Recently, it has been found that the small local curvature can also be obtained if the balloon is covered by a diamond-shaped net with a vertically elongated shape. The development of the super-pressure balloon using this method was started from a 3-m balloon with a polyethylene film covered by a net using Kevlar ropes. The ground inflation test showed the expected high burst pressure. Then, a 6-m and a 12-m balloon using a polyethylene film and a net using the Vectran were developed and stable deployment was checked through the ground inflation tests. The flight test of a 3000 m³ balloon was performed in 2013 and shown to resist a pressure of at least 400 Pa. In the future, after testing a new design to relax a possible stress concentration around the polar area, test flights of scaled balloons will be performed gradually enlarging their size. The goal is to launch a 300,000 m³ super-pressure balloon.     

Properties of tandem balloons connected by extendable suspension wires

The tandem balloon system has been known as a candidate system for long duration flight balloons. In this paper, the properties of the system are analytically studied in a new way by introducing an extendable suspension wire in the Sky Anchor configuration, which consists of a zero-pressure main balloon suspending a payload and a super-pressure balloon suspended below the payload. It was found that extension of the suspension wire between the payload and the super-pressure balloon can extend the capability of the tandem system; the altitude of the zero-pressure balloon can be changed without any consumables except some energy, and the day–night oscillation of the balloon altitude can be suppressed. This property is useful as the vehicle for long duration flights. It is also pointed out that the method to control the altitude of a balloon using an additional suspended super-pressure balloon can also be applied for super-pressure balloons.     

First results of a stratospheric experiment using a montgolfiere infra-rouge (MIR)

An original stratospheric experiment in the tropics has been performed on board the new long duration balloon system developped by the Centre National d'Etudes Spatiales in France. The experiment together with the performances reached in flight are presented.     

Study of seasonal variation of winds in upper stratosphere over Hyderabad

A predictability of the stratospheric zonal winds above 38 km during the turnaround is an essential parameter for planning of the high-altitude scientific balloon flights. This information is more relevant in the case of Hyderabad balloon facility which is closer to equator and has much more unstable wind reversal patterns which appears to have changed enormously during the last decade probably in correlation with the global warming. With a majority of our flights reaching the altitudes of 38–42 km and the requirement of long float durations, a prior knowledge of wind pattern during the summer and winter turnaround seasons is highly desirable. Furthermore, the flight operation corridor for balloon flights from Hyderabad is limited to 400 km and though in the west direction there are flat lands, in all other three directions, the landscape is dotted by water bodies, reserve forests and hilly terrain, and therefore need of such a data is essential. In order to establish the climatology of the stratospheric winds and study their inter-annual variability over Hyderabad for the turnaround periods, we have made a detailed analysis of the United Kingdom Meteorological office data between 2000 and 2007, to derive average wind parameters (magnitude, direction) at different ceiling altitudes above 38 km. These results can be used only as general trend of stratospheric wind and should not be the limitation of the UKMO Data.     

Development overview of the revised NASA Ultra Long Duration Balloon

The desire for longer duration stratospheric flights at constant float altitudes for heavy payloads has been the focus of the development of the National Aeronautics and Space Administration’s (NASA) Ultra Long Duration Balloon (ULDB) effort. Recent efforts have focused on ground testing and analysis to understand the previously observed issue of balloon deployment. A revised approach to the pumpkin balloon design has been tested through ground testing of model balloons and through two test flights. The design approach does not require foreshortening, and will significantly reduce the balloon handling during manufacture reducing the chances of inducing damage to the envelope. Successful ground testing of model balloons lead to the fabrication and test flight of a ∼176,000 m³ (∼6.2 MCF – Million Cubic Foot) balloon. Pre-flight analytical predictions predicted that the proposed flight balloon design to be stable and should fully deploy. This paper provides an overview of this first test flight of the revised Ultra Long Duration Balloon design which was a short domestic test flight from Ft. Sumner, NM, USA. This balloon fully deployed, but developed a leak under pressurization. After an extensive investigation to the cause of the leak, a second test flight balloon was fabricated. This ∼176,000 m³ (∼6.2 MCF) balloon was flown from Kiruna, Sweden in June of 2006. Flight results for both test flights, including flight performance are presented.     

Program of balloon launchings in Indonesia in the 1980s

The stratospheric balloon program in Indonesia was initiated in the year 1974, by sending a team to CNES, France, to undergo a job training. The first balloon launching conducted in the year 1975 and since then other launchings have been carried out regularly. The launchings were done on the island of Bali and East Java, because these areas are ideal of that purpose as the upperwind over these areas almost constantly blows easterly.The program of balloon launchings in the 1980's will be improved by the construction of a permanent launching station situated in Mojokerto, East Java, and the addition of Rawin sonde RD 650 CS equipment, Balte Telecommand with 10 addresses and recovery equipment. The volume of balloons will be larger i.e. up to 13.000 m³, enabling to carry heavier payload for longer flight time duration. Also a tethered balloon will be operated for experimentation of TV relay station and communication, especially remote areas.     

The Mars Environment Analogue Platform long duration balloon flight

The MEAP (Mars Environment Analogue Platform) mission was to fly a stratospheric balloon on a semicircular trajectory around the North Pole in summer 2008. The balloon platform carried the high-resolution neutral gas mass spectrometer P-BACE (Polar Balloon Atmospheric Composition Experiment) as scientific payload. MEAP/P-BACE is a joint project between the Esrange Space Center, Sweden, the University of Bern, Switzerland and the Swedish Institute of Space Physics (IRF), Kiruna, Sweden. Mission objectives were to validate the platform for future long duration flights around the North pole, to validate the P-BACE instrument design for planetary mission applications (conditions in the Earth stratosphere are similar to the conditions at the Mars surface), to study variation of the stratospheric composition during the flight and to gain experience in balloon based mass spectrometry. All objectives were fulfilled.     

A new reeling technique for very long extension scanning in the stratosphere

A balloon borne winching system has been developed for extending a very long tether with payload down into the stratosphere and recovering it; this has been flight proven by being carried to an altitude of 40 km, lowering a 62 kg stratospheric photochemistry experiment 12 km at a descent velocity of ～6–8 m/sec and recovering it at comparable velocities. During the first flight, data gave no evidence of dynamic instabilities due to the system or the stratospheric interactions. The future utility of this payload is discussed with attention to the design factors that bound the range of performance of this type of system.     

Studies of thin film nonlinear viscoelasticity for superpressure balloons

In order to provide scientists with a stratospheric platform from which to conduct long duration research, a superpressure balloon is desired which will maintain a relatively constant volume for weeks at a time. The pumpkin shaped balloon has been developed by making use of the surface lobing to limit the circumferential stress and meridional tendons to carry the loads in the other direction. However, in order to prevent geometric instabilities during deployment and after pressurization, the design should eliminate as much excess material as possible while not exceeding the permissible stresses of the material. This paper will describe the behavior of the very thin membrane material selected for this application and the limits of the film in a biaxial state of stress. In addition, it is shown that the viscoelastic nature of the film will limit the stress by causing a reduced radius of curvature in the lobe of the pumpkin.     

A challenge to the highest balloon altitude

Development of a balloon to fly at higher altitudes is one of the most attractive challenges for scientific balloon technologies. After reaching the highest balloon altitude of 53.0 km using the 3.4 μm film in 2002, a thinner balloon film with a thickness of 2.8 μm was developed. A 5000 m³ balloon made with this film was launched successfully in 2004. However, three 60,000 m³ balloons with the same film launched in 2005, 2006, and 2007, failed during ascent. The mechanical properties of the 2.8 μm film were investigated intensively to look for degradation of the ultimate strength and its elongation as compared to the other thicker balloon films. The requirement of the balloon film was also studied using an empirical and a physical model assuming an axis-symmetrical balloon shape and the static pressure. It was found that the film was strong enough. A stress due to the dynamic pressure by the wind shear is considered as the possible reason for the unsuccessful flights. A 80,000 m³ balloon with cap films covering 9 m from the balloon top will be launch in 2011 to test the appropriateness of this reinforcement.     

一种基于地转风模型的平流层风场插值方法

平流层风场水平分量的数据精度和密度对高空气球实验的轨迹预测精度和飞行控制精度有着直接的影响。面向平流层风场，提出一种基于地转风模型的插值方法。该方法通过改进科里奥利频率公式，并用二维卷积计算地转风模型，提升了地转风模型的计算效率和低纬度地区风场精度，再用迭代二元线性回归和改进的自适应观测场偏差权重矩阵减小了观测误差对插值结果的影响。实验结果表明:所提插值方法能有效提升平流层风场插值计算速度，并对平流层风场水平分量的插值精度有显著提升。      

Feasibility study of a sea-anchored stratospheric balloon for long-duration flights

Sea-anchored balloons are stratospheric super-pressure balloons that are anchored to the sea. The sea-anchored balloon is a simple system that has the capability for long-duration flights, fixed-point observations, flexible launch windows, easy telemetry links to ground stations, and quick recoveries. Such balloons are not required to fly through the jet stream while tethered to the ground or sea, because the tether is deployed from a reel on the balloon after reaching a floating altitude. In this study, the feasibility of the sea-anchored balloon is investigated, with particular emphasis on the tether strength, balloon altitude, and system mass, based on the present technological level of the tether’s specific strength. Although the wind distribution with altitude is a dominant factor for feasibility, a sea-anchored balloon with an altitude of about 25 km would be feasible if the velocity of the jet stream is sufficiently low. The sea-anchored balloon can be simply flight-tested, since additional ground facilities and special flight operations are not necessary.     

Evolution of scientific ballooning and its impact on astrophysics research

As we celebrate the centennial year of the discovery of cosmic rays on a manned balloon, it seems appropriate to reflect on the evolution of ballooning and its scientific impact. Balloons have been used for scientific research since they were invented in France more than 200 years ago. Ballooning was revolutionized in 1950 with the introduction of the so-called natural shape balloon with integral load tapes. This basic design has been used with more or less continuously improved materials for scientific balloon flights for more than a half century, including long-duration balloon (LDB) flights around Antarctica for the past two decades. The U.S. National Aeronautics and Space Administration (NASA) is currently developing the next generation super-pressure balloon that would enable extended duration missions above 99.5% of the Earth’s atmosphere at any latitude. The Astro2010 Decadal Survey report supports super-pressure balloon development and the giant step forward it offers with ultra-long-duration balloon (ULDB) flights at constant altitudes for about 100 days.     

The radiation controlled balloon (RACOON)

The RACOON concept permits the flight of large, low-cost polyethylene balloons for several weeks at stratospheric altitudes without ballast. The theory of operations is described. The RACOON balloon ascends each morning and descends at night. This movement of 15 to 20 km in altitude provides an ideal platform for vertical soundings and sampling measurements in the stratosphere. Results of a number of globe-circling flights are presented.     

A balloon-borne sun-tracking multichannel photometer for atmospheric aerosol measurements

A balloon borne multichannel photometer for measurement of atmospheric scattering in the near ultraviolet and the visible wavelength regions has been developed at the Physical Research Laboratory, Ahmedabad for study of the size distribution and number density of aerosols at tropospheric and lower stratospheric altitudes. The instrumentation involves tracking the sun in elevation and scanning in azimuth. The payload was recently flown on a 100 kg. balloon from the Hyderabad Balloon Facility on 18 April 1984. The balloon reached a float altitude of 35 km and good quality data has been obtained from an altitude of 6 km upto float altitude. Data analysis is still in progress. The present paper details the instrument design and presents a few illustrations of the instrument performance from this flight.     

Analysis of long-endurance station-keeping flight scenarios for stratospheric airships in the presence of thermal effects

The ability to achieve long-endurance station-keeping flights makes stratospheric airships desirable platforms for the provision of communication and surveillance services. To maintain long-endurance flights, it is necessary to consider the problem of energy consumption. In this paper, we discuss long-endurance flight scenarios of stratospheric airships in the presence of thermal effects. The balance between buoyancy and gravity is influenced by thermal effects during the diurnal cycle. We perform a theoretical analysis based on the helium’s mass, pressure differential, and altitude as the main factors. To verify the effectiveness of the control over the pressure differential and the altitude, three long-endurance flight scenarios are proposed and compared. Then, the corresponding optimization problems are constructed to determine the energy-minimum flight. Finally, further efforts are made to reduce energy consumption. The realization and limitations of two strategies for improvement are analyzed. A comparison with other scenarios shows the effectiveness of energy conservation. The study in this paper thus provides a reference for station-keeping applications of stratospheric airships.     

USV test flight by stratospheric balloon: Preliminary mission analysis

The Unmanned Space Vehicle test flights will use a 7 m 1300 kg aircraft. The first three launches will take place at the Italian Space Agency ASI base in Trapani–Milo, Sicily, through a stratospheric balloon that will drop the aircraft at a predefined height. After free fall acceleration to transonic velocities, the parachute deployment will allow a safe splash down in the central Mediterranean Sea. The goal of this article is to show the preliminary analysis results for the first USV flight.We carried out a statistical study for the year 2000–2003, evaluating the typical summer and winter launch windows of the Trapani–Milo base.First, in the center Mediterranean, we define safe recovery areas. They cannot be reached during the balloon ascending phase so, after a sufficiently long floating part able to catch the open sea, the balloon will go down to the release height (24 km). The simulation foresees a 400,000 m³ balloon and 3 valves for the altitude transfer.A safe splash down must occur far enough from the nearest coast: the minimum distance is considered around 25 km. The vehicle should be released at a distance, from the nearest coast, greater than this minimum amount plus the USV model maximum horizontal translation, during its own trajectory from balloon separation to splash down. In this way we define safe release areas for some possible translations.Winter stratospheric winds are less stable. The winter average flight duration is 7 h and it is probably too long for the diurnal recovery requirement and its scheduled procedures.Comparing past stratospheric balloons flights and trajectories computed using measured meteorological data (analysis), with their predictions made using forecast models and soundings, we obtain the standard deviation of the trajectory forecast uncertainty at the balloon–aircraft separation. Two cases are taken into account: predictions made 24 and 6 h before the launch.Assuming a Gaussian latitudinal uncertainty distribution for the prediction 6 h before the launch, we are able to identify the forecast trajectories that have a probability greater than 97% to reach the safe release areas.Simulating the summer windows trajectories for the years from 2000 to 2003 and for the favorable ground wind days, we obtain the number of trajectories with the desired forecast probabilities.     

平流层飞艇总体设计的基础问题

平流层飞艇是一种新型的长航时临近空间飞行器，具有驻空高度高、驻空时间长、承载能力大、使用效费比高等特点，在对地观测及通信中继等领域具有广泛应用前景。但是该飞行器系统十分复杂，技术与设计实现难度大，总体设计需要考虑的基础问题及解决方案尚不完全明晰。根据平流层大气风场、温度和压力的基础特征，考虑平流层环境对平流层飞艇总体设计的影响，根据空气动力学与热力学基本理论，分析平流层飞艇的显著特征及与常规低空飞艇的区别，研究这些基础问题对平流层飞艇总体设计的影响，为平流层飞艇技术发展提供建议和参考。      

Hardware qualification for scientific ballooning missions

The European Stratospheric Balloon Observatory (ESBO) initiative aims at simplifying the access to stratospheric balloon missions. We plan to provide platforms and support with instrument design in order to support scientists. During the design process, the inevitable question of qualification for the harsh flight conditions arises. Unfortunately, there is no existing standard for qualification of stratospheric ballooning hardware. Thus, we developed a qualification procedure for use within ESBO and similar projects.In this paper, we present our analysis of the environmental conditions in the stratosphere. While conditions at typical balloon float altitudes are similar to the space environment, there are also some relevant differences. For example, the thermal environment is dominated by radiation and thermal conduction, but the remaining atmosphere still supports a certain amount of convection. The remaining atmospheric pressure in the stratosphere also leads to reduced arcing distances. Vibrational loads are far less than for space missions, but quasi-static or shock loads may occur. The criticality of radiation increases with mission duration.Based on the environmental conditions, we present the qualification procedures for ESBO, which are based on the European Cooperation for Space Standardization (ECSS) standards for space systems. Overtesting against too high requirements leads to overengineering, driving mission cost and mitigating the advantages of balloons over space missions. Therefore, we modified the ECSS standards to fit typical scientific ballooning missions over several days at altitudes up to 40 km. Furthermore, we analyzed design rules for space systems with regard to their relevance for scientific ballooning, including material and component selection. We present the experience from the hardware qualification process for the ESBO prototype STUDIO (Stratospheric UV Demonstrator of an Imaging Observatory). Even though boundary conditions are different for each individual mission, we aimed for a broader approach: We investigated more general requirements for scientific ballooning missions to support future flights.     

Mechanical properties of ANTRIX balloon film and fabrication of single cap large volume balloons

The zero pressure plastic balloons used for high altitude studies are generally made from polyethylene material. Tensile properties of the thin film polymer are the key parameters for material selection due to extremely low temperature of −90 °C encountered by the balloons in the tropopause region during the ascent at equatorial latitudes. The physical and structural properties of the material determine the uniformity of the stress distribution over the entire shell. Load stresses from the suspended load propagate via load tapes heat sealed along with the gore seals as per the balloon design. A balance between this heat seal strength and the film strength is a desirable property of the basic resin in terms of the bubble strength, gauge uniformity, and long-term storage properties. In addition, the design of the top shell of the balloon and its stress distribution play an important role since only a fraction of the balloon is deployed during the filling operation and the ascent. In this paper we describe the mechanical properties of the ‘ANTRIX’ film developed by us and the optimized design of single cap balloons, which have been successfully used in our experiments over the past 5 years.