Calibration of Envisat radar altimeter over Lake Issykkul

This study presents the results of calibration/validation (C/V) of Envisat satellite radar altimeter over Lake Issykkul located in Kyrgyzstan, which was chosen as a dedicated radar altimetry C/V site in 2004. The objectives are to estimate the absolute altimeter bias of Envisat and its orbit based on cross-over analysis with TOPEX/Poseidon (T/P), Jason-1 and Jason-2 over the ocean. We have used a new method of GPS data processing in a kinematic mode, developed at the Groupe de Recherche de Geodesie Spatiale (GRGS), which allows us to calculate the position of the GPS antenna without needing a GPS reference station. The C/V is conducted using various equipments: a local GPS network, a moving GPS antenna along the satellites tracks over Lake Issykkul, In Situ level gauges and weather stations. The absolute bias obtained for Envisat from field campaigns conducted in 2009 and 2010 is between 62.1 and 63.4 ± 3.7 cm, using the Ice-1 retracking algorithm, and between 46.9 and 51.2 cm with the ocean retracking algorithm. These results differ by about 10 cm from previous studies, principally due to improvement of the C/V procedure. Apart from the new algorithm for GPS data processing and the orbit error reduction, more attention has been paid to the GPS antenna height calculation, and we have reduced the errors induced by seiche over Lake Issykkul. This has been assured using cruise data along the Envisat satellite track at the exact date of the pass of the satellite for the two campaigns. The calculation of the Envisat radar altimeter bias with respect to the GPS levelling is essential to allow the continuity of multi-mission data on the same orbit, with the expected launch of SARAL/Altika mission in 2012. Implications for hydrology in particular, will be to produce long term homogeneous and reliable time series of lake levels worldwide.     

GPS-based sea level measurements to help the characterization of land contamination in coastal areas

The Corsica site has been established in 1996 to perform altimeter calibration on TOPEX/Poseidon and then on its successors Jason-1 and Jason-2. The first chosen location was under the #85 ground track that overflight the Senetosa Cape. In 2005, it was decided to develop another location close to Ajaccio, to be able to perform the calibration of Envisat and in a next future of SARAL/AltiKa that will flight over the same ground tracks. Equipped with various instruments (tide gauges, permanent GPS, GPS buoy, weather station…) the Corsica calibration site is able to quantify the altimeter Sea Surface Height bias but also to give an input on the origin of this bias (range, corrections, orbits, …). Due to the size of Corsica (not a tiny island), the altimeter measurement system (range and corrections) can be contaminated by land. The aim of this paper is to evaluate this land contamination by using GPS measurements from a fixed receiver on land and from another receiver onboard a life buoy. Concerning the altimeter land contamination, we have quantify that this effect can reach 8 mm/km and then affects the Sea Surface Height bias values already published in the framework of the Corsica calibration site by 5–8 mm for TOPEX and Jason missions. On the other hand, the radiometer measurements (wet troposphere correction) are also sensitive to land and we have been able to quantify the level of improvement of a dedicated coastal algorithm that reconciles our results with those coming from other calibration sites. Finally, we have also shown that the standard deviation of the GPS buoy sea level measurements is highly correlated (∼87%) with the Significant Wave Height derived from the altimeters and can be used to validate such parameter.     

利用高频天波返回散射反演台风中心和风速

通过分析高频天波返回散射地（海）杂波频谱分布特性,构建三谱滤波器模型,实现多类型频谱中一阶海杂波峰值比的提取,结果与实测数据吻合较好.基于台风中心与区域一阶海杂波峰值比相关性分析,结合后向差分法,有效确定了台风中心,结果与气象部门发布数据趋势上基本一致,平均绝对误差约38km.使用修正经验模型法初步开展了台风中心最大风速和台风中心附近的风速反演,结果与气象部门发布数据分布基本一致.研究结果表明高频天波返回散射探测对大范围、远距离海态监测具有重要意义.      

The contribution of local gravimetric geoid models to the calibration of satellite altimetry data and an outlook of the latest GOCE GGM performance in Gavdos

The use of geoid heights has been one of the available methodologies utilized for the independent calibration/validation of altimeters on-board satellites. This methodology has been employed for long in the Gavdos dedicated cal/val facility (Crete, Greece), where calibration results for the Jason satellites have been estimated, both for ascending and descending passes. The present work gives a detailed overview of the methodology followed in order to estimate a high-resolution and accuracy gravimetric geoid model for the wider Gavdos area, in support of the on-going calibration work. To estimate the geoid model, the well-known remove-compute-restore method is used while residual geoid heights are estimated through least-squares collocation so that associated errors are determined as well. It is found that the estimated formal geoid errors from LSC along passes 018 and 109 of Jason satellites, used for the bias estimation, range between ±0.8–1.6 cm. The so-derived geoid heights are employed in the determination of the Jason-2 altimeter bias for all available cycles (cycles 1-114, spanning the period from July 2008 to August 2011) together with the RioMed DOT model. From the results acquired the Jason-2 bias has been estimated to be +196.1 ± 3.2 mm for pass 109 and +161.9 ± 5.1 mm for pass 018. Within the same frame, the GOCE/GRACE-based geopotential model GOCO02s has been used to estimate the mean dynamic ocean topography and the steady-state circulation in the area around Gavdos. The so-derived DOT model was used to estimate the Jason-2 bias in an effort to evaluate the performance of satellite-only geoid models and investigate whether their spatial resolution and accuracy provides some improvement w.r.t. traditional local gravimetric geoids. From the results acquired with geoid heights from GOCO02s, the estimated Jason-2 bias deviates significantly from that of the local gravimetric model, which can be attributed to a possible mean offset and the low resolution of GOCE-based GGMs. On the other hand, when the newly estimated GOCE-based DOT was employed with geoid heights from the local gravimetric geoid model, the Jason-2 bias has been estimated to be +185.1 ± 3.2 mm for pass 109 and +130.2 ± 5.1 mm for pass 018.     

Detection of Envisat RA2/ICE-1 retracked radar altimetry bias over the Amazon basin rivers using GPS

Altimetry is now routinely used to monitor stage variations over rivers, including in the Amazon basin. It is desirable for hydrologic studies to be able to combine altimetry from different satellite missions with other hydrogeodesy datasets such as leveled gauges and watershed topography. One requirement is to accurately determine altimetry bias, which could be different for river studies from the altimetry calibrated for deep ocean or lake applications. In this study, we estimate the bias in the Envisat ranges derived from the ICE-1 waveform retracking, which are nowadays widely used in hydrologic applications. As a reference, we use an extensive dataset of altitudes of gauge zeros measured by GPS collocated at the gauges. The thirty-nine gauges are spread along the major tributaries of the Amazon basin. The methodology consists in jointly modeling the vertical bias and spatial and temporal slope variations between altimetry series located upstream and downstream of each gauge. The resulting bias of the Envisat ICE-1 retracked altimetry over rivers is 1.044 ± 0.212 m, revealing a significant departure from other Envisat calibrations or from the Jason-2 ICE-1 calibration.     

ASAR imaging for coastal upwelling in the Baltic Sea

Analysis of Envisat Advanced Synthetic Aperture Radar (ASAR) and Aqua/Terra Moderate Imaging Spectrometer (MODIS) infrared (IR) imagery of coastal upwelling in the southeastern Baltic Sea is presented. It is found that upwelling features are well distinct in the SAR images, and the leading imaging mechanism appears to be the change of the marine atmospheric boundary layer (MABL) stratification over the sea surface temperature (SST) front. This finding is supported by model calculations of the MABL transformation supplemented with the SAR backscatter calculations based on the CMOD4 model. In addition an empirical dependence of the SAR contrasts over the upwelling region on the wind speed and the SST drop is suggested. Finally, surface slicks accumulated in the sea surface current convergence zones generate additional distinct features in SAR imagery. This effect is interpreted within the framework of the coastal current circulation model based on analysis of the SST snapshot.     

Regional in situ validation of satellite altimeters: Calibration and cross-calibration results at the Corsican sites

The in situ validation of the satellite altimeter sea surface heights is generally performed either at a few local points directly flown over by the satellites or using the global tide gauge network. A regional in situ calibration method was developed by NOVELTIS in order to monitor the altimeter data quality in a perimeter of several hundred kilometres around a given in situ calibration site. The primary advantage of this technique is its applicability not only for missions flying over dedicated sites but also for missions on interleaved or non repetitive orbits. This article presents the altimeter bias estimates obtained with this method at the Corsican calibration site, for the Jason-1 mission on its nominal and interleaved orbits as well as for the Jason-2 and Envisat missions. The various regional bias estimates (8.2 cm and 7.4 cm for Jason-1 respectively on the nominal and interleaved orbits in Senetosa, 16.4 cm for Jason-2 in Senetosa and 47.0 cm for Envisat in Ajaccio, with an accuracy between 2.5 cm and 4 cm depending on the mission) are compared with the results obtained by the other in situ calibration teams. This comparison demonstrates the coherency at the centimetre level, the stability and the generic character of the method, which would also be of benefit to the new and future altimeter missions such as Cryosat-2, SARAL/AltiKa, Sentinel-3, Jason-3, Jason-CS.     

Validation of an active transponder for KOMPSAT-5 SAR image calibration

This paper describes the development and validation of a transportable active transponder designed for the image calibration of Korea Multi-Purpose Satellite-5 (KOMPSAT-5) with a synthetic aperture radar (SAR). Ground targets are essential in SAR image calibration. The environment for the deployment of ground targets for SAR image calibration should provide uniformity and minimum interference. The Amazon or deserts are regarded as desirable environments. However, such environments for SAR image calibration are difficult to find in Korea. Thus, it will be advantageous to have an active transponder whose performance will not be severely limited by the absence of such uniform environment. We have therefore developed an active transponder which has an adjustable internal delay and into which the orbit data of an arbitrary satellite can be loaded. The stored obit data with the aid of an internal global positioning system (GPS) receiver and gyroscope enables the active transponder to point to a selected satellite. In addition, a virtual deployment of the active transponder is possible due to its adjustable internal delay. Thus, the developed active transponder can be deployed at any place without environmental constraint. The performance of the developed active transponder is validated using the satellite TerraSAR-X, which is already in operation. The test results show that the active transponder is successfully compliant with the requirements for KOMPSAT-5 image calibration.     

Cross testing of ionosphere models IRI-2001 and IRI-2007, data from satellite altimeters (Topex/Poseidon and Jason-1) and global ionosphere maps

In this study, we use a great body of statistical data covering the entire 23rd solar cycle to cross test data of satellite altimeters, Global Ionosphere Maps and the International Reference Ionosphere models, IRI-2001 and IRI-2007. It is revealed that experimental TEC values of the satellite altimeters regularly exceed the model ones by ∼3 TECU (1 TECU = 10¹⁶ m⁻²). The best possible value of difference between TECs obtained from altimeter and GIM-map data significantly differs for different laboratories: the maximum for CODG data falls on 2.5 TECU, ESAG – 3 TECU, JPLG – 0 TECU, UPCG – 2 TECU. The dependence of experimental and model data root-mean-square deviation on the F10.7 index is shown to be nearly linear. IRI-2001 and IRI-2007 relative errors are characterized by considerable 11-year and annual variations. Given the geomagnetic planetary index K_p under 7, IRI-2001 and IRI-2007 reproduce TEC in the ionosphere with an accuracy of ∼30% relative to measurement data from satellite altimeters. The amplitude of absolute error variations resulting from the difference in ionization enhancement between the model and the real ionosphere during the morning solar terminator transit is ∼5 TECU.     

海表温度对中法海洋卫星散射计测量的影响

卫星散射计通过测量海表粗糙度反演全球海面风场。对于Ku波段散射计，海表粗糙不仅和海面风场相关，还受海表温度的二阶效应调制。定量研究了海表温度对中法海洋卫星（CFOSAT）散射计（CSCAT）反演风速和后向散射测量的影响。结果表明，CSCAT两种极化方式测量的后向散射系数都会受到海表温度的影响，但是垂直极化中低入射角（θ <36°）测量的后向散射系数几乎不随温度变化。因此CSCAT的风速偏差也随海表温度的变化而变化，且随着入射角的增大和风速的减小，海表温度对风速偏差的影响程度增大。在数据分析的基础上提出了一种考虑海表温度影响机制的地球物理模式函数，为未来CFOSAT散射计风场反演的海温校正提供参考。     

全极化散射计极化失真误差校正方法

全极化散射计是一种新型微波散射计，可以同时测量目标的同极化和交叉极化散射系数.一方面能够解决传统散射计在海面风场反演中的风向模糊问题，提高海面风场测量精度，另一方面交叉极化散射系数可以有效提高海面风速测量范围，解决台风灾害监测和预报问题.利用全极化散射计数据进行高精度海面风场反演，首先需要解决全极化散射计系统极化失真误差导致无法准确测量目标不同极化散射系数的问题.本文基于全极化散射计信号模型推导了极化失真误差影响下极化散射系数模型，并对极化失真误差影响进行了定量分析.在极化散射系数模型基础上，通过引入海面散射特性假设和极化定标技术推导了极化散射系数校正模型.基于RADARSAT-2获取的不同区域海面全极化散射系数数据仿真误差影响下极化散射系数并利用该模型进行校正，结果表明该方法可以有效校正极化失真误差，显著提高极化散射系数测量精度.      

Semi-empirical model of middle atmosphere wind from the ground to the lower thermosphere

During recent years, special attention has been paid to understanding the background circulation of the middle atmosphere. Particularly in the mesosphere/lower thermosphere (MLT) region, this has involved including data from a range of new radar measurements. It has also involved the comparison of existing empirical middle atmosphere wind models, such as CIRA-86 and HWM-93 to the new data. This has led to the construction of empirical models of MLT winds such as the Global Empirical Wind Model (GEWM). Further investigations are aimed at the construction of new empirical and semi-empirical wind models of the entire middle atmosphere including these new experimental results. The results of a new wind climatology (0–100 km) are presented here, based upon the GEWM, a reanalysis of stratospheric data, and a numerical model which is used to fill the gap between data from the stratospheric and MLT regions.     

GSFC DORIS contribution to ITRF2008

The NASA GSFC DORIS analysis center has provided weekly DORIS solutions from November 1992 to January 2009 (839 SINEX files) of station positions and Earth Orientation Parameters for inclusion in the DORIS contribution to ITRF2008. The NASA GSFC GEODYN orbit determination software was used to process the orbits and produce the normal equations. The weekly SINEX gscwd10 submissions included DORIS data from Envisat, TOPEX/Poseidon, SPOT-2, SPOT-3, SPOT-4, SPOT-5. The orbits were mostly seven days in length (except for weeks with data gaps or maneuvers). The processing used the GRACE-derived EIGEN-GL04S1 gravity model, updated modeling for time-variable gravity, the GOT4.7 ocean tide model and tuned satellite-specific macromodels for SPOT-2, SPOT-3, SPOT-4, SPOT-5 and TOPEX/Poseidon. The University College London (UCL) radiation pressure model for Envisat improves nonconservative force modeling for this satellite, reducing the median residual empirical daily along-track accelerations from 3.75 × 10⁻⁹ m/s² with the a priori macromodel to 0.99 × 10⁻⁹ m/s² with the UCL model. For the SPOT and Envisat DORIS satellite orbits from 2003 to 2008, we obtain average RMS overlaps of 0.8–0.9 cm in the radial direction, 2.1–3.4 cm cross-track, and 1.7–2.3 cm along-track. The RMS orbit differences between Envisat DORIS-only and SLR & DORIS orbits are 1.1 cm radially, 6.4 cm along-track and 3.7 cm cross-track and are characterized by systematic along-track mean offsets due to the Envisat DORIS system time bias of ±5–10 μs. We obtain a good agreement between the geometrically-determined geocenter parameters and geocenter parameters determined dynamically from analysis of the degree one terms of the geopotential. The intrinsic RMS weekly position repeatability with respect to the IDS-3 combination ranges from 2.5 to 3.0 cm in 1993–1994 to 1.5 cm in 2007–2008.     

一种基于温度参数的热层密度修正方法

热层大气的阻力效应是影响低轨航天器大量空间操作的重要因素, 尤其是经验密度模式, 其固有的至少15%的内符合误差已严重制约航天器轨道计算精度的提高. 针对广泛应用的经验密度模式, 选择物理背景简明、关联参数较少的JACCHIA71模式, 以地磁平静条件下的全球散逸层顶温度最小值T_c及125 km高度拐点温度T_x为对象, 建立密度相对于上述温度参数的条件方程, 推导密度相对于温度参数的解析偏导数, 并给出其最小二乘解. 同时, 利用CHAMP卫星数据对模式进行修正, 模式平均误差从40%降低至3%左右. 通过TG01飞行器的轨道预报比较, 修正前后轨道预报位置精度从2 km提升至1 km左右. 经过CHAMP卫星和TG01飞行器的实测数据检验, 验证了修正算法的正确性和有效性.      

Meteorological variations in the middle clouds of Venus from VEGA balloon in situ measurements

Instruments aboard the gondolas of the two VEGA balloons obtained in situ measurements of pressure, temperature, vertical velocity relative to the balloon, cloud particle backscatter, lightning and the ambient light level. Atmospheric motions at the balloon float altitudes were also determined from Earth-based tracking results. To illustrate the history of the balloon flights and to facilitate comparisons between some of the different observed quantities, measurements of pressure, temperature and backscatter are presented as time series for the entire lifetime of each balloon. Both long and short period variations have been detected. In addition, the environmental entropy encountered by each balloon will be discussed.     

Integrating Non-Tidal Sea Level data from altimetry and tide gauges for coastal sea level prediction

The main objective of this paper is to integrate Non-Tidal Sea Level (NSL) from the joint TOPEX, Jason-1 and Jason-2 satellite altimetry with tide gauge data at the west and north coast of the United Kingdom for coastal sea level prediction. The temporal correlation coefficient between altimetric NSLs and tide gauge data reaches a maximum higher than 90% for each gauge. The results show that the multivariate regression approach can efficiently integrate the two types of data in the coastal waters of the area. The Multivariate Regression Model is established by integrating the along-track NSL from the joint TOPEX/Jason-1/Jason-2 altimeters with that from eleven tide gauges. The model results give a maximum hindcast skill of 0.95, which means maximum 95% of NSL variance can be explained by the model. The minimum Root Mean Square Error (RMSe) between altimetric observations and model predictions is 4.99 cm in the area. The validation of the model using Envisat satellite altimetric data gives a maximum temporal correlation coefficient of 0.96 and a minimum RMSe of 4.39 cm between altimetric observations and model predictions, respectively. The model is furthermore used to predict high frequency NSL variation (i.e., every 15 min) during a storm surge event at an independent tide gauge station at the Northeast of the UK (Aberdeen).     

中法海洋卫星微波散射计在轨性能验证

中法海洋卫星（CFOSAT）微波散射计是国际上第一个旋转扇形波束体制散射计，通过优化雷达观测几何实现对地面目标多角度和多方位的高精度测量，提高海面风场、土壤湿度和海冰面积等地球物理参数的反演精度.根据CFOSAT卫星2018年10月发射以来的在轨测试数据，结合散射计系统特点，分析验证了星上定标数据和后向散射系数反演结果的正确性，并对CFOSAT首批科学数据进行了定量分析和系统评价.结果表明，CFOSAT散射计在轨工作状态良好，实际性能与设计预期一致，风速测量精度优于1.5m·-1，风向测量精度优于15°，空间分辨率可达12.5km，在近岸风场监测、土壤湿度遥感和海冰面积估计等应用领域具有独特的优势.      

基于移动站的转发式地面站设备时延标校方法

在转发式卫星测定轨系统中,基于伪码测距原理的星地距离测量是实现卫星精密定轨和高精度时间比对的基础。为获得高精度的星地距离,需要将地面站设备时延从伪码测距值中精确扣除。在转发式卫星测轨原理的基础上,提出了基于移动站的转发式地面站设备时延标校方法,实现了对转发式地面站设备时延的标校,标校精度能够优于0.5ns,对提高转发式卫星定轨精度和卫星双向时间比对精度具有重要作用。     

The compatability of cloud tracked winds from the United States,European, and Japanese geostationary satellites

Overlap of coverage of the five geostationary satellites has allowed an intercomparison of the FGGE cloud tracked winds. No attempt was made during FGGE to standardize the cloud tracking techniques. In spite of this potential for differences between data sets, the compatability of the various cloud wind data sets was generally quite good. The vector magnitude differences between nearly co-located vectors showed similar cumulative frequency statistics for all data producers. A study of systematic biases which could affect a global wind analysis of any given synoptic period showed that image alignment errors caused less than 2 m s^?1 bias for all data producers except the NESS high level winds which had an average bias of slightly greater than 3 m s^?1. This appears to be caused by the manual alignment of images in the movie loops. Height bias studies showed the Japanese winds to be higher than other data producers by as much as 100 mb for both the high and low levels winds. Height biases appear to be caused by the differences in cloud wind height assignment procedures.