Impact of GPS antenna phase center variations on precise orbits of the GOCE satellite

The first European Space Agency Earth explorer core mission GOCE (Gravity field and steady-state Ocean Circulation Explorer) has been launched on March 17, 2009. The 12-channel dual-frequency Global Positioning System receiver delivers 1 Hz data and provides the basis for precise orbit determination (POD) on the few cm-level for such a very low orbiting satellite (254.9 km). As a member of the European GOCE Gravity Consortium, which is responsible for the GOCE High-level Processing Facility (HPF), the Astronomical Institute of the University of Bern (AIUB) provides the Precise Science Orbit (PSO) product for the GOCE satellite. The mission requirement for 1-dimensional POD accuracy is 2 cm. The use of in-flight determined antenna phase center variations (PCVs) is necessary to meet this requirement. The PCVs are determined from 154 days of data and the magnitude is up to 3-4 cm. The impact of the PCVs on the orbit determination is significant. The cross-track direction benefits most of the PCVs. The improvement is clearly seen in the orbit overlap analysis and in the validation with independent Satellite Laser Ranging (SLR) measurements. It is the first time that SLR could validate the cross-track component of a LEO orbit.     

LEO enhanced Global Navigation Satellite System (LeGNSS) for real-time precise positioning services

Global Navigation Satellite System (GNSS) has been widely used in many geosciences areas with its Positioning, Navigation and Timing (PNT) service. However, GNSS still has its own bottleneck, such as the long initialization period of Precise Point Positioning (PPP) without dense reference network. Recently, the concept of PNTRC (Positioning, Navigation, Timing, Remote sensing and Communication) has been put forward, where Low Earth Orbit (LEO) satellite constellations are recruited to fulfill diverse missions. In navigation aspect, a number of selected LEO satellites can be equipped with a transmitter to transmit similar navigation signals to ground users, so that they can serve as GNSS satellites but with much faster geometric change to enhance GNSS capability, which is named as LEO constellation enhanced GNSS (LeGNSS). As a result, the initialization time of PPP is expected to be shortened to the level of a few minutes or even seconds depending on the number of the LEO satellites involved. In this article, we simulate all the relevant data from June 8th to 14th, 2014 and investigate the feasibility of LeGNSS with the concentration on the key issues in the whole data processing for providing real-time PPP service based on a system configuration with fourteen satellites of BeiDou Navigation Satellite System (BDS), twenty-four satellites of the Global Positioning System (GPS), and sixty-six satellites of the Iridium satellite constellations. At the server-end, Precise Orbit Determination (POD) and Precise Clock Estimation (PCE) with various operational modes are investigated using simulated observations. It is found out that GNSS POD with partial LEO satellites is the most practical mode of LeGNSS operation. At the user-end, the Geometry Dilution Of Precision (GDOP) and Signal-In-Space Ranging Error (SISRE) are calculated and assessed for different positioning schemes in order to demonstrate the performance of LeGNSS. Centimeter level SISRE can be achieved for LeGNSS.     

卫星与测站钟差支持条件下的GEO卫星精密定轨

在基于伪距的GEO卫星精密定轨中, GEO卫星的静地特性导致定轨解算无法对星地组合钟差进行有效估计, 需要独立的时间同步支持. 本文讨论了卫星和测站钟差支持条件下的GEO卫星定轨原理, 利用仿真数据系统地分析了中国区域网跟踪条件下GEO卫星的定轨精度, 从定性和定量角度分析了钟差二次项、星地时间同步精度、站间时间同步精度及系统差等因素对定轨精度的影响.      

Precise orbit determination using the batch filter based on particle filtering with genetic resampling approach

In this study, genetic resampling (GRS) approach is utilized for precise orbit determination (POD) using the batch filter based on particle filtering (PF). Two genetic operations, which are arithmetic crossover and residual mutation, are used for GRS of the batch filter based on PF (PF batch filter). For POD, Laser-ranging Precise Orbit Determination System (LPODS) and satellite laser ranging (SLR) observations of the CHAMP satellite are used. Monte Carlo trials for POD are performed by one hundred times. The characteristics of the POD results by PF batch filter with GRS are compared with those of a PF batch filter with minimum residual resampling (MRRS). The post-fit residual, 3D error by external orbit comparison, and POD repeatability are analyzed for orbit quality assessments. The POD results are externally checked by NASA JPL’s orbits using totally different software, measurements, and techniques. For post-fit residuals and 3D errors, both MRRS and GRS give accurate estimation results whose mean root mean square (RMS) values are at a level of 5 cm and 10–13 cm, respectively. The mean radial orbit errors of both methods are at a level of 5 cm. For POD repeatability represented as the standard deviations of post-fit residuals and 3D errors by repetitive PODs, however, GRS yields 25% and 13% more robust estimation results than MRRS for post-fit residual and 3D error, respectively. This study shows that PF batch filter with GRS approach using genetic operations is superior to PF batch filter with MRRS in terms of robustness in POD with SLR observations.     

Precise orbit determination and baseline consistency assessment for Swarm constellation

Precise orbit determination (POD) and precise baseline determination (PBD) of Swarm satellites with 4 years of data are investigated. Ambiguity resolution (AR) plays a crucial role in achieving the best orbit accuracy. Swarm POD and PBD based on single difference (SD) AR and traditional double difference (DD) AR methods are explored separately. Swarm antenna phase center variation (PCV) corrections are developed to further improve the orbit determination accuracy. The code multipath of C1C, C1W and C2W observations is first evaluated and clear variations in code noise related to different receiver settings are observed. Carrier phase residuals of different time periods and different loop tracking settings of receiver are studied to explore the effect of ionospheric scintillation on POD. The reduction of residuals in the polar and geomagnetic equator regions confirms the positive impact of the updated carrier tracking loops (TLs) on POD performance. The SD AR orbits and orbits with float ambiguity (FA) are compared with the Swarm precise science orbits (PSOs). An average improvement of 27 %, 4 % and 16 % is gained in along-track, cross-track and radial directions by fixing the ambiguity to integer. For Swarm-A/B and Swarm-B/C formations, specific days are selected to perform the DD AR-based POD during which the average distance of the formation satellites is less than 5000 km. Satellite laser ranging (SLR) observations are employed to validate the performance of FA, SD AR and DD AR orbits. The consistency between the SD AR orbits and SLR data is at a level of 10 mm which shows an improvement of 25 % when comparing with the FA results. An SLR residuals reduction of 15 % is also achieved by the DD AR solution for the selected days. Precise relative navigation is also an essential aspect for spacecraft formation flying missions. The closure error method is proposed to evaluate the baseline precision in three dimensions. A baseline precision of 1–3 mm for Swarm-A/C formation and 3–5 mm for Swarm-A/B and Swarm-B/C satellite pairs is verified by both the consistency check and closure error method.     

环火星测量数据处理及精密轨道确定

为支持我国首次火星探测任务取得圆满成功，宇航动力学国家重点实验室将全自主开发的精密定轨平台系统，应用于环火星轨道确定中。为满足多对象、多弧段、多中心天体的定轨需求，平台系统设计了卫星结构、测站结构、观测结构和天体结构4大基础结构，并在4大基础结构之上，设计了灵活的弧段结构和估计结构。为验证平台系统是否具备环火星定轨能力，平台系统首先使用2020年上半年跟踪火星快车实验的数据对测量模型进行了检核，得到了理论测距和实测测距偏差（11m~21m）；其次，使用2009年实测双程测速和三程测速数据定轨，单独使用双程测速定轨，轨道与欧空局精密星历位置偏差最大不超过100m，测速残差的均方根（Root Mean Square, RMS）为0.0137(cm/s)。使用三程测速定轨，位置偏差不超过250m，三程测速RMS为0.0119（cm/s）；最后，使用两天三站测距仿真进行了自定轨验证，初轨和随机差都基本收敛回仿真初值。结果显示，宇航动力学国家重点实验室精密定轨系统能够满足我国首次火星探测任务的基本需求。     

VLBI observations to the APOD satellite

The APOD (Atmospheric density detection and Precise Orbit Determination) is the first LEO (Low Earth Orbit) satellite in orbit co-located with a dual-frequency GNSS (GPS/BD) receiver, an SLR reflector, and a VLBI X/S dual band beacon. From the overlap statistics between consecutive solution arcs and the independent validation by SLR measurements, the orbit position deviation was below 10?cm before the on-board GNSS receiver got partially operational. In this paper, the focus is on the VLBI observations to the LEO satellite from multiple geodetic VLBI radio telescopes, since this is the first implementation of a dedicated VLBI transmitter in low Earth orbit. The practical problems of tracking a fast moving spacecraft with current VLBI ground infrastructure were solved and strong interferometric fringes were obtained by cross-correlation of APOD carrier and DOR (Differential One-way Ranging) signals. The precision in X-band time delay derived from 0.1?s integration time of the correlator output is on the level of 0.1?ns. The APOD observations demonstrate encouraging prospects of co-location of multiple space geodetic techniques in space, as a first prototype.     

Precision orbit determination performance for CryoSat-2

In this paper we discuss our efforts to perform precision orbit determination (POD) of CryoSat-2 which depends on Doppler and satellite laser ranging tracking data. A dynamic orbit model is set-up and the residuals between the model and the tracking data is evaluated. The average r.m.s. of the 10?s averaged Doppler tracking pass residuals is approximately 0.39?mm/s; and the average of the laser tracking pass residuals becomes 1.42?cm. There are a number of other tests to verify the quality of the orbit solution, we compare our computed orbits against three independent external trajectories provided by the CNES. The CNES products are part of the CryoSat-2 products distributed by ESA. The radial differences of our solution relative to the CNES precision orbits shows an average r.m.s. of 1.25?cm between Jun-2010 and Apr-2017. The SIRAL altimeter crossover difference statistics demonstrate that the quality of our orbit solution is comparable to that of the POE solution computed by the CNES. In this paper we will discuss three important changes in our POD activities that have brought the orbit performance to this level. The improvements concern the way we implement temporal gravity accelerations observed by GRACE; the implementation of ITRF2014 coordinates and velocities for the DORIS beacons and the SLR tracking sites. We also discuss an adjustment of the SLR retroreflector position within the satellite reference frame. An unexpected result is that we find a systematic difference between the median of the 10 s Doppler tracking residuals which displays a statistically significant pattern in the South Atlantic Anomaly (SSA) area where the median of the velocity residuals varies in the range of ?0.15 to +0.15?mm/s.     

Evaluation on real-time dynamic performance of BDS in PPP,RTK, and INS tightly aided modes

Since China’s BeiDou satellite navigation system (BDS) began to provide regional navigation service for Asia-Pacific region after 2012, more new generation BDS satellites have been launched to further expand BDS’s coverage to be global. In this contribution, precise positioning models based on BDS and the corresponding mathematical algorithms are presented in detail. Then, an evaluation on BDS’s real-time dynamic positioning and navigation performance is presented in Precise Point Positioning (PPP), Real-time Kinematic (RTK), Inertial Navigation System (INS) tightly aided PPP and RTK modes by processing a set of land-borne vehicle experiment data. Results indicate that BDS positioning Root Mean Square (RMS) in north, east, and vertical components are 2.0, 2.7, and 7.6?cm in RTK mode and 7.8, 14.7, and 24.8?cm in PPP mode, which are close to GPS positioning accuracy. Meanwhile, with the help of INS, about 38.8%, 67.5%, and 66.5% improvements can be obtained by using PPP/INS tight-integration mode. Such enhancements in RTK/INS tight-integration mode are 14.1%, 34.0%, and 41.9%. Moreover, the accuracy of velocimetry and attitude determination can be improved to be better than 1?cm/s and 0.1°, respectively. Besides, the continuity and reliability of BDS in both PPP and RTK modes can also be ameliorated significantly by INS during satellite signal missing periods.     

粗差拟准检定法在星载GPS低轨卫星定轨中的应用

利用自适应卡尔曼滤波进行星载GPS低轨卫星定轨时,必须解决量测方程中经常存在的粗差问题．在分析以往方法的优缺点后,用拟准检定法来探测和修正量测方程中存在的粗差．该法的优点是辨识粗差准确率高,能同时定位多个粗差．另外,为了克服星载GPS低轨卫星定轨的滤波器可能出现的数值不稳定性及发散现象,还采用了UD分解算法及Sage自适应滤波器．最后用一个CHAMP卫星的模拟算例验证本方法的可行性和有效性．     

Geostationary orbit determination using SATRE

A new strategy of precise orbit determination (POD) for GEO (Geostationary Earth Orbit) satellite using SATRE (SAtellite Time and Ranging Equipment) is presented. Two observation modes are proposed and different channels of the same instruments are used to construct different observation modes, one mode receiving time signals from their own station and the other mode receiving time signals from each other for two stations called pairs of combined observations. Using data from such a tracking network in China, the results for both modes are compared. The precise orbit determination for the Sino-1 satellite using the data from 6 June 2005 to 13 June 2005 has been carried out in this work. The RMS (Root-Mean-Square) of observing residuals for 3-day solutions with the former mode is better than 9.1 cm. The RMS of observing residuals for 3-day solutions with the latter mode is better than 4.8 cm, much better than the former mode. Orbital overlapping (3-day orbit solution with 1-day orbit overlap) tests show that the RMS of the orbit difference for the former mode is 0.16 m in the radial direction, 0.53 m in the along-track direction, 0.97 m in the cross-track direction and 1.12 m in the 3-dimension position and the RMS of the orbit difference for the latter mode is 0.36 m in the radial direction, 0.89 m in the along-track direction, 1.18 m in the cross-track direction and 1.52 m in the 3-dimension position, almost the same as the former mode. All the experiments indicate that a meter-level accuracy of orbit determination for geostationary satellite is achievable.     

Precise orbit determination and precision comparison for FY3C and FY3D with receiver antenna GPS and BDS PCV using spaceborne BDS and GPS observation data

The FY3C and FY3D satellites were equipped with global navigation satellite occultation detector (GNOS) receivers that received both GPS and BDS-2 signals. For further improving precise orbit determination (POD) precisions, we estimated receiver GPS and BDS signal phase center variations (PCV) models with 2° and 5° resolutions and set the different weights for GPS and BDS-2 observations in the combined POD. The BDS-based POD precision using BDS-2 satellite antenna phase center offset (PCO) values from the China Satellite Navigation Office (CSNO) are not as accurate as those obtained from the International GNSS Service (IGS) Multi-GNSS experiments project (MGEX). The estimated receiver GPS and BDS PCV models with 2° and 5° resolutions were estimated from the GPS phase residuals of GPS-based POD and BDS phase residuals of combined POD, respectively. In most cases, the POD precisions using the estimated PCVs with 2° resolution are superior to those with 5° resolution. The precisions of the BDS-based POD and combined POD were both improved by introducing the receiver BDS PCV models. The weighting for GPS and BDS-2 observations can further improve the precision of the combined POD. The tested results of selected weights are better than those with equal weight in the combined POD. The experiment results show that orbital precisions of FY3C are worse than those of FY3D.     

Geosynchronous satellites expanding a future GNSS satellite constellation: A precise orbit determination study

The integration of geosynchronous orbit (GSO) satellites in Global Navigation Satellite Systems (GNSS) is mostly discussed to enable a regional enhancement for tracking. But how do GSO satellites affect the orbit determination of the rest of the constellation? How accurately can these orbits be determined in a future GNSS tracking scenario with optical links? In this simulation study we analyze the benefit of GSO satellites as an expansion of a MEO (Medium Earth Orbit) satellite constellation – we selected the Galileo satellite constellation – for MEO Precise Orbit Determination (POD). We address not only the impact on POD of MEO satellites but also the possibility to precisely determine the GSO satellites – geostationary orbits (GEO) and inclined geosynchronous orbits (IGSO) – in such an expanded MEO constellation. In addition to GNSS microwave observations, we analyze the influence of different optical links between the participating entities: Optical two-way Inter-Satellite Links (OISL) and ground-space oriented Optical Two-Way Links (OTWL). These optical measurements together with the GNSS microwave observations give a remarkable benefit for the POD capability. In the case of GNSS and OTWL, we simulate the measurements with regard to a network of 16 ground stations. We pay great attention to the simulation of systematic effects of all measurement techniques. We discuss the influence on the systematic errors as well as the formal orbit uncertainties. A MEO constellation expanded with GSO satellites as well as the use of optical links together with GNSS observations not only improves the MEO satellite orbits but also the GSOs to a great extent.     

附加先验轨道约束的LEO几何法实时精密定轨验证分析

低轨卫星的实时精密定轨能够极大拓展其完成复杂科学任务的能力,例如实时环境监测、机动控制和卫星自主导航等.本文根据几何法实时精密定轨模型,提出了附加LEO先验轨道约束从而改善实时定轨的精度、收敛速度和稳定性的构想.分别采用广播星历、超快速星历预报部分和实时精密星历,设计了6种实时定轨方案,并利用Swarm-A,B,C星7天的观测数据进行方案验证与分析.结果表明,使用广播星历、IGU和IGC星历的方案精度递增,附加先验轨道约束能够进一步提升精度.使用IGC星历并附加标准差为1m的先验轨道约束后,在径向、切向和法向的定轨精度分别达到6.12cm,5.55cm和4.98cm.此外,附加先验轨道约束能够显著提升收敛速度,使用IGC星历平均收敛时间约为31min,附加标准差为1m的先验轨道约束后收敛仅需约4min.      

基于单频星载GPS数据的低轨卫星精密定轨

为满足搭载单频GPS接收机低轨卫星的精密定轨需求以及深化单频定轨研究,文中解决了单频星载GPS数据的周跳探测问题,并利用“海洋二号”（HY-2A）卫星及“资源三号”（ZY-3）卫星的单频星载GPS实测数据采用两种方法确定了二者的简化动力学轨道,并通过观测值残差分析、与双频精密轨道比较、激光测卫数据检核等方法对所得轨道精度进行评定。结果表明,在不考虑电离层延迟影响的情况下,HY-2A卫星定轨精度为2~3dm,ZY-3卫星为1m左右;而采用半和改正组合消除电离层延迟一阶项影响后,二者定轨精度均显著提高,HY-2A卫星三维精度提高至1dm左右,ZY-3卫星提高至1~2dm。文章的研究成果表明,搭载单频GPS接收机的低轨卫星也可获得厘米级的定轨精度。     

Near real-time BDS GEO satellite orbit determination and maneuver analysis with reversed point positioning

The Geostationary Earth Orbit (GEO) satellite is a crucial part of the BeiDou Navigation Satellite System (BDS) constellation. However, due to various perturbation forces acting on the GEO satellite, it drifts gradually over time. Thus, frequent orbit maneuvers are required to maintain the satellite at its designed position. During the orbit maneuver and recovery periods, the orbit quality of the maneuvered satellite computed with broadcast navigation ephemeris will be significantly degraded. Furthermore, the conventional dynamic Precise Orbit Determination (POD) approach may not work well, because of a lack of publicly available satellite information for modeling the thrust forces. In this paper, a near real-time approach free of thrust forces modeling is proposed for BDS GEO satellite orbit determination and maneuver analysis based on the Reversed Point Positioning (RPP). First, the station coordinates and receiver clock offsets are estimated by GPS/BDS combined Single Point Positioning (SPP) with single-frequency phase-smoothed pseudorange observations. Then, with the fixed station coordinates and receiver clock offsets, the RPP method can be conducted to determine the GEO satellite orbits. When no orbit maneuvers occur, the proposed method can obtain orbit accuracies of 0.92, 2.74, and 8.30?m in the radial, along-track, and cross-track directions, respectively. The average orbit-only Signal-In-Space Range Error (SISRE) is 1.23?m, which is slightly poorer than that of the broadcast navigation ephemeris. Using four days of GEO maneuvered datasets, it is further demonstrated that the derived orbits can be employed to characterize the behaviors of GEO satellite maneuvers, such as the time span of the maneuver as well as the satellite thrusting accelerations. These results prove the efficiency of the proposed method for near real-time GEO satellite orbit determination during maneuvers.     

The impact of orbital errors on the estimation of satellite clock errors and PPP

Precise satellite orbit and clocks are essential for providing high accuracy real-time PPP (Precise Point Positioning) service. However, by treating the predicted orbits as fixed, the orbital errors may be partially assimilated by the estimated satellite clock and hence impact the positioning solutions. This paper presents the impact analysis of errors in radial and tangential orbital components on the estimation of satellite clocks and PPP through theoretical study and experimental evaluation. The relationship between the compensation of the orbital errors by the satellite clocks and the satellite-station geometry is discussed in details. Based on the satellite clocks estimated with regional station networks of different sizes (∼100, ∼300, ∼500 and ∼700 km in radius), results indicated that the orbital errors compensated by the satellite clock estimates reduce as the size of the network increases. An interesting regional PPP mode based on the broadcast ephemeris and the corresponding estimated satellite clocks is proposed and evaluated through the numerical study. The impact of orbital errors in the broadcast ephemeris has shown to be negligible for PPP users in a regional network of a radius of ∼300 km, with positioning RMS of about 1.4, 1.4 and 3.7 cm for east, north and up component in the post-mission kinematic mode, comparable with 1.3, 1.3 and 3.6 cm using the precise orbits and the corresponding estimated clocks. Compared with the DGPS and RTK positioning, only the estimated satellite clocks are needed to be disseminated to PPP users for this approach. It can significantly alleviate the communication burdens and therefore can be beneficial to the real time applications.     

Comparison of convergence time and positioning accuracy among BDS,GPS and BDS/GPS precise point positioning with ambiguity resolution

Precise point positioning (PPP) usually takes about 30?min to obtain centimetre-level accuracy, which greatly limits its application. To address the drawbacks of convergence speed and positioning accuracy, we develop a PPP model with integrated GPS and BDS observations. Based on the method, stations with global coverage are selected to estimate the fractional cycle bias (FCB) of GPS and BDS. The short-term and long-term time series of wide-lane (WL) FCB, and the single day change of narrow-lane (NL) FCB are analysed. It is found that the range of GPS and BDS non-GEO (IGSO and MEO) WL FCB is stable at up to a 30-day-time frame. At times frame of up to 60?days, the stability is reduced a lot. Whether for short-term or long-term, the changes in the BDS GEO WL FCB are large. Moreover, BDS FCB sometimes undergoes a sudden jump. Besides, 17 and 10 stations were used respectively to investigate the convergence speed and positioning errors with six strategies: BDS ambiguity-float PPP (Bfloat), GPS ambiguity-float PPP (Gfloat), BDS/GPS ambiguity-float PPP (BGfloat), BDS ambiguity-fixed PPP (Bfix), GPS ambiguity-fixed (Gfix), and BDS/GPS ambiguity-fixed (BGfix). The average convergence speed of the ambiguity-fixed solution is greatly improved compared with the ambiguity-float solution. In terms of the average convergence time, the Bfloat is the longest and the BGfix is the shortest among these six strategies. Whether for ambiguity-float PPP or ambiguity-fixed PPP, the convergence reduction time in three directions for the combined system is the largest compared with the single BDS. The average RMS value of the Bfix in three directions (easting (E), northing (N), and up (U)) are 2.0?cm, 1.5?cm, and 5.9?cm respectively, while those of the Gfix are 0.8?cm, 0.5?cm, and 1.7?cm. Compared with single system, the BDS/GPS combined ambiguity-fixed system (BGfix) has the fastest convergence speed and the highest accuracy, with average RMS as 0.7?cm, 0.5?cm, and 1.9?cm for the E, N, U components, respectively.