Dynamical analysis of a spinning solar sail

This paper discusses the orbit and attitude dynamics of a solar sail, and gives the sufficient conditions of a stable orbit and attitude coupled system. The stability of the coupled system is determined by the orbit stability and attitude stability. Based on the sufficient conditions, a spin-stabilized solar sail of cone configuration is proposed to evolve in the heliocentric displaced orbit. For this kind of configuration, the attitude is always stable by spinning itself. The orbit stability depends on the orbit parameters of the heliocentric displaced orbit, the ratio of the orbit radius to displaced distance and orbit angular velocity. If the center of mass and center of pressure overlap, it can be proved that the coupled system is stable when the orbit parameters are chosen in the stable region. When the center of mass and center of pressure offset exists, the stability of the coupled system can not be judged. A numerical example is given and the result shows that both the orbit and attitude are stable for the case.     

Performance analysis of an attitude control system for solar sails using sliding masses

This paper deals with the attitude control performance analysis of a square solar sail. Two sliding masses are moved inside and along mast lanyards for the control around the pitch and yaw axes. An optimal linear controller with a feedback and a feedforward part is used to control the attitude of the sail. Numerical simulations have been carried out to investigate the system’s ability of performing precise and near-time-optimal reorientation maneuvers as well as the controller’s sensitivity with respect to the sail parameters, as the center of pressure to the center of mass offset or the sail’s size. Our simulation results are finally shown and discussed.     

太阳帆航天器编队维持和重构的方法研究

针对高面质比航天器可以利用太阳光压进行轨道控制的特点,本文提出一种太阳帆航天器编队构型维持和重构的方法.该方法通过控制主从航天器太阳帆姿态角和反射系数,调整主从航天器之间的光压差,产生抵消编队成员间相对运动受到摄动差或进行轨道机动时所需的连续小推力,从而实现编队构型的维持和重构.仿真结果表明,在主航天器太阳帆的姿态角和反射系数相对固定的条件下,对于太阳同步轨道上的高面质比太阳帆航天器编队,使用滑模控制方法,能够调整编队中从航天器太阳帆的姿态角和反射系数产生推力抵消摄动力影响,达到长期维持太阳帆航天器编队构型的目的;通过开环控制方法,能够调整编队中从航天器太阳帆的姿态角和反射系数产生连续小推力,在较长时间周期内实现编队重构.     

On-orbit verification of fuel-free attitude control system for spinning solar sail utilizing solar radiation pressure

This paper introduces a new attitude control system for a solar sail, which leverages solar radiation pressure. This novel system achieves completely fuel-free and oscillation-free attitude control of a flexible spinning solar sail. This system consists of thin-film-type devices that electrically control their optical parameters such as reflectivity to generate an imbalance in the solar radiation pressure applied to the edge of the sail. By using these devices, minute and continuous control torque can be applied to the sail to realize very stable and fuel-free attitude control of the large and flexible membrane. The control system was implemented as an optional attitude control system for small solar power sail demonstrator named IKAROS (Interplanetary Kite-craft Accelerated by Radiation Of the Sun). In-orbit attitude control experiments were conducted, and the performance of the controller was successfully verified in comparison with the ground-based analytical performance estimation.     

姿态角幅值约束下的太阳帆Lissajous轨道保持控制

太阳帆航天器以两姿态角作为轨道控制输入时, 其轨道动力学方程具有非仿射非线性特性. 通过人工平动点处线性化获得的线性系统可完成太阳帆航天器轨道保持控制器的分析与设计. 由于线性近似模型为有误差模型, 存在近似有效范围约束, 表现为轨道高度约束和姿态角幅值约束. 本文研究了姿态角幅值约束对线性近似模型有效性的影响, 通过计算给出满足近似误差要求的姿态角幅值约束. 当控制输入存在幅值约束时, 控制器轨道修正能力受到束缚. 通过研究姿态角幅值约束下的最大允许入轨误差, 设计了最大允许入轨误差下线性二次型调节器(LQR)用于轨道保持控制, 并将控制器应用于太阳帆日地三体系统非线性模型中, 实现了日地人工L₁点Lissajous轨道最大允许入轨误差的控制收敛和良好精度下的轨道保持控制.      

Shape optimization of a three-dimensional membrane-structured solar sail using an angular momentum unloading strategy

A shape of the satellite’s solar sail membrane is essential for unloading angular momentum in the three-axis stabilized attitude control system because the three-dimensional solar sail can receive solar radiation pressure from arbitrary directions. In this paper, the objective is the shape optimization of a three-dimensional membrane-structured solar sail using the angular momentum unloading strategy. We modelled and simulated the solar radiation pressure torque, for unloading angular momentum. Using the simulation system, since the unloading angular momentum rate is maximized, the shape of the three-dimensional solar sail was optimized using a Genetic algorithm and Sequential Quadratic Programming. The unloading velocity in the optimized shaped solar sail was greatly improved with respect to a conventional flat or pyramid solar sail.     

High performance two degrees of freedom attitude control for solar sails

The purpose of this paper is to present a high performance solar sail attitude controller which uses ballast masses moving inside the sail’s booms as actuators and to demonstrate its ability of performing time efficient reorientation maneuvers. The proposed controller consists of a combination of a feedforward and a feedback controller, which takes advantage of the feedforward’s fast response and the feedback’s ability of responding to unpredicted disturbances. The feedforward controller considers the attitude dynamics of the sailcraft as well as the disturbance torque due to the center of pressure offset to the center of mass of the sailcraft. Additional disturbance torques, like those coming from the environment or from asymmetry of the spacecraft structure, are then handled by the feedback controller. Simulation performance results are finally compared against results available in the literature.     

Optimal steering law of refractive sail

The interaction between electromagnetic waves and matter is the working principle of a photon-propelled spacecraft, which extracts momentum from the solar radiation to obtain a propulsive acceleration. An example is offered by solar sails, which use a thin membrane to reflect the impinging photons. The solar radiation momentum may actually be transferred to matter by means of various optical phenomena, such as absorption, emission, or refraction. This paper deals with the novel concept of a refractive sail, through which the Sun’s light is refracted by crossing a film made of polymeric micro-prisms. The main feature of a refractive sail is to give a large transverse component of thrust even when the sail nominal plane is orthogonal to the Sun-spacecraft line. Starting from the recent literature results, this paper proposes a semi-analytical thrust model that estimates the characteristics of the propulsive acceleration vector as a function of the sail attitude angles. Such a mathematical model is then used to analyze a simplified Earth-Mars and Earth-Venus interplanetary transfer within an optimal framework.     

Spinning solar sail orbit steering via spin rate control

The orbit of a solar sail can be controlled by changing the attitude of the spacecraft. In this study, we consider the spinning solar power sail IKAROS (Interplanetary Kite-craft Accelerated by Radiation Of the Sun), which is managed by Japan Aerospace Exploration Agency (JAXA). The IKAROS attitude, i.e., the direction of its spin-axis, is nominally controlled by the rhumb-line control method. By utilizing the solar radiation torque, however, we are able to change the direction of the spin-axis by only controlling its spin rate. With this spin rate control, we can also control indirectly the solar sail’s trajectory. The main objective of this study is to construct the orbit control strategy of the solar sail via the spin-rate control method. We evaluate this strategy in terms of its propellant consumption compared to the rhumb-line control method. Finally, we present the actual flight attitude data of IKAROS and the change of its trajectory.     

CubeSail: A low cost CubeSat based solar sail demonstration mission

CubeSail is a nano-solar sail mission based on the 3U CubeSat standard, which is currently being designed and built at the Surrey Space Centre, University of Surrey. CubeSail will have a total mass of around 3 kg and will deploy a 5 × 5 m sail in low Earth orbit. The primary aim of the mission is to demonstrate the concept of solar sailing and end-of-life de-orbiting using the sail membrane as a drag-sail. The spacecraft will have a compact 3-axis stabilised attitude control system, which uses three magnetic torquers aligned with the spacecraft principle axis as well as a novel two-dimensional translation stage separating the spacecraft bus from the sail. CubeSail’s deployment mechanism consists of four novel booms and four-quadrant sail membranes. The proposed booms are made from tape-spring blades and will deploy the sail membrane from a 2U CubeSat standard structure. This paper presents a systems level overview of the CubeSat mission, focusing on the mission orbit and de-orbiting, in addition to the deployment, attitude control and the satellite bus.