共查询到20条相似文献,搜索用时 78 毫秒
1.
针对复合材料高质量的加工要求,结合各加工技术的优点,本文提出二维超声复合电解/放电加工技术(2UECM/EDM),并对其表面生成机理进行深入研究。利用二维超声辅助磨削加工时单磨粒的运动轨迹对加工表面沟槽的加宽作用和电解/放电加工的整平作用,通过研磨面积比(δs)来分析复合材料表面形貌和表面粗糙度(Ra)的变化规律,并进行了复合材料SiCp/Al维超声复合电解/放电加工的表面生成机理对比试验。结果表明,单周进给距离、电压和二维超声振幅等参数影响加工表面质量。其中,表面粗糙度与磨粒单周进给距离的变化趋势一致;较高电压时电解/放电加工效应显著,导致增强颗粒裸露进而增加了Ra;轴向和切向二维振动共同作用下显著增大δs值,而其值在1.8附近时Ra出现明显的转折变化趋势。因此,当δs大于1.8时的工具和工件振幅以及较低电压参数,加工时对增强颗粒的拖曳和碾压可以显著降低表面不平度、较大幅度提高工件表面质量。 相似文献
2.
本文就钛合金叶片电解加工后的表面粗糙度、点蚀、烧伤及吸氢等问题进行了分析并提出了改善钛合金电解加工表面完整性的措施。 相似文献
3.
为了研究单晶硅电火花线切割(WEDM)表面损伤层的损伤形式和形成机理,以电火花线切割加工后的单晶硅表面为研究对象,采用表面形貌观察分析及择优腐蚀方法研究了单晶硅经过电火花线切割后的加工表面.研究结果表明单晶硅经电火花放电加工后表面损伤形式分为4种:热损伤、应力损伤、热与应力综合作用损伤及电解/电化学腐蚀损伤.热损伤使得硅表面形成多晶或非晶硅;应力损伤使硅表面产生裂纹;热与应力综合作用会产生小孔效应,且随着放电功率密度的增加,小孔会明显增多;电解/电化学作用会加快损伤区域及杂质元素富集区域的腐蚀. 相似文献
4.
5.
6.
喷射液束电解-激光复合加工工艺试验研究 总被引:5,自引:1,他引:4
喷射液束电解 激光复合加工是一项新探索的加工技术,其特点是既发挥激光加工的高效率,又借助喷射电液束的冷却、冲刷、电解作用而实现在线去除再铸层。基于该加工原理的分析,在对激光电解液中衰减特性研究的基础上,研制了试验系统并对不锈钢片进行了打孔工艺试验。试验结果表明,应用液压1.5 MPa、浓度18%的NaNO3电解液的喷射液束电解-激光复合加工可实现再铸层减少90%以上。通过对打孔形貌的对比以及加工工艺规律的初步分析,揭示了喷射液束电解-激光复合加工以激光加工为主,电解加工辅助去除再铸层的加工原理,证实了该复合加工工艺的可行性,可望在航空航天领域得到广泛工程应用。 相似文献
7.
8.
9.
整体叶盘电解加工中,流场对加工稳定性起着重要作用,电解液进液角度对流场均匀性具有重要影响。针对由叶尖至叶根流动模式,设计了5种电解液进液角度流动模型(12°、22°、32°、42°以及52°),并开展电解加工流场仿真研究。结果表明,电解液进液角度为32°时,平均流速为19.01 m/s,流速均方差为6.33,满足整体叶盘电解加工对流场的要求。在电解液进液角度为32°的流场形式下,开展整体叶盘电解加工试验,加工过程稳定,试件表面无流纹,加工精度为0.12 mm,表面粗糙度为Ra0.353μm,验证了流场的合理性。 相似文献
10.
11.
基于飞机油箱模型形状特征油量测量切片步长选择方法研究 总被引:1,自引:0,他引:1
在分析飞机数字式油量测量过程中目前广泛使用的切片法油量测量原理的基础上,针对现有的定步长切片法无法得到准确、可靠的燃油质量特性数据库的缺陷,结合对飞机油箱模型形状特征的分析,提出了基于飞机油箱模型形状特征的油量测量切片步长选择方法。此方法包括切片步长整体和局部选择两个过程,整体选择以实现相邻两切片平面所夹油箱模型体积近似相等为目的来确定切片步长,以体现油箱模型截面整体变化规律;局部选择以设计切片平面与截面突变平面重合或尽可能接近的方式,突出油箱截面的局部变化特征。实验结果表明:该切片步长选择方法较定步长方法能够建立更为合理、可靠的燃油质量特性数据库,从而提高了油量测量精度。 相似文献
12.
13.
The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow 总被引:1,自引:0,他引:1
This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation. 相似文献
14.
Abnormal Shape Mould Winding 总被引:1,自引:0,他引:1
Fu Hongya Wang Xianfeng Han Zhenyu Fu Yunzhong 《中国航空学报》2007,20(6):552-558
为解决网格化芯模的缠绕问题,本文提出了复合材料面片缠绕机理;接着详细分析了面片缠绕过程中的芯模凹曲面上纤维滑线和架空现象,应用微分几何曲面理论和空间几何理论,提出判据及其解决方案;最后,针对飞机发动机进气道的缠绕成型,编制缠绕控制程序并进行相应的实验,验证了面片缠绕方法的可行性。 相似文献
15.
16.
航天器返回地球的气动特性综述 总被引:4,自引:0,他引:4
航天器返回地球的飞行过程中,气动特性是实现将宇宙飞行速度减到落地前速度、保证再入飞行得到有效控制以及再入防热安全可靠的关键因素。针对简单旋成体气动外形、半弹道式再入控制、烧蚀防热类返回航天器,综述了返回地球过程中变化的空气流域特性、航天器周围的气体绕流环境、空气与航天器作用产生的动力学与热效应等。系统地给出了该类航天器的再入气动特性参数与飞行性能的共性规律,包括:气动阻力与再入减速、气动升力与再入轨迹控制、配平攻角与飞行稳定性、气动加热与防热,以及再入过程中不同气动特性航天器、气象条件变化等对再入飞行性能的影响规律。为航天器开展返回飞行过程的跨流域气动性能工程研制提供设计参考。 相似文献
17.
基于马赫数分布可控曲面外/内锥形基准流场的前体/进气道一体化设计 总被引:4,自引:1,他引:3
提出了一种高超声速飞行器乘波前体的外锥形基准流场设计方法,在锥面马赫数分布规律给定的条件下,通过有旋特征线法实现反设计,提高了基准流场设计的灵活性。该基准流场通过锥形"下凹"弯曲激波和波后等熵压缩波系压缩气流,可以在较短的长度内完成高效压缩。基于反正切马赫数分布外锥形基准流场设计的乘波前体具有较高的容积率,乘波特性良好且出口均匀,设计点时有黏升阻比为1.89。另外,基于该乘波前体和马赫数分布可控的内收缩进气道给出了一种双乘波的前体与进气道一体化设计方案,实现了内外流分别独立乘波,充分发挥了乘波前体和内收缩进气道的各自优势。 相似文献
18.
IntroductionExpensive turbine parts like HPT(HighPressure Turine)blades or vanes are replaced bynew parts in case of damage.For example theburn through of the inner side of a blade or vane(Figure 1)is a frequently appearing damage,which cannot be repaired… 相似文献
19.
Advanced gas turbine stages are designed to operate at increasingly higher inlet temperatures to increase thermal efficiency and specific power output.To maintain durability and reasonable life,film cooling is needed in addition to internal cooling,especially for the first stage.Film cooling lowers material temperature by forced convection inside film-cooling holes and by forming a layer of coolant about component surfaces to insulate them from the hot gases.Unfortunately,each cooling jet forms a pair of counter-rotating vortices that entrains hot gas and causes the film-cooling jet to lift off from the surface that it is intended to protect.This paper gives an overview of efforts to enhance the effectiveness of film-cooling.This paper also describes two new design concepts.One design concept seeks to minimize the entrainment of hot gases underneath of film-cooling jets by using flow-aligned blockers.The other design concept shifts the interaction between the approaching hot gas and the cooling jet to occur further above the surface by using an upstream ramp.For both design concepts,computational fluid dynamics results are presented to examine their usefulness in enhancing film-cooling effectiveness. 相似文献
20.
《中国航空学报》2014,(4):F0003-F0003
<正>About Journal Chinese Journal of Aeronautics(CJA)is a comprehensive academic journal dealing with the fields of aeronautics and astronautics.It reports researches concerning the two fields in China and abroad to promote the academic exchange.Founded in 1988 and sponsored by the Chinese Society of Aeronautics and Astronautics and Beihang University,CJA publishes papers bimonthly,with issues released in February,April,June,August,October and December. 相似文献