Effects of test vehicle patterns on cellular coverage measurements

Mobile test systems intended for cellular phone coverage measurements suffer from uncertainties, which are caused by the unpredictable radiation pattern of the measuring antenna installation. Not only do adjacent structures and very common multiple antennas disturb the characteristics, but also in the case of an ideal position does the vertical lobing introduce errors exceeding 10 dB. The problems are likely to be worse in dense urban areas, where multipath from surrounding buildings is the dominating propagation mode     

Theoretical analysis of the sequential lobing technique

A theoretical analysis of the sequential lobing technique for target angle tracking is presented. The signal power received by each antenna beam is assumed to pass through a logarithmic amplifier. A rigorous statistical approach is adopted in the analysis for both non-fluctuating and fluctuating targets. Closed form expressions are derived for the normalized mean error and rms error of the angle estimate for Swerling 0, I, II, and III targets. Results are compared with those obtained using a simplified approach for the non-fluctuating target     

Analysis and Design of Antennas for Air Traffic Collision Avoidance Systems

The analysis and design procedure of an antenna for a CW Doppler radar system being developed for pilot warning of midair collision hazards is presented. The antenna consists of two vertical arrays of half-wavelength dipoles mounted near a circular conducting cylinder. Each vertical array is composed of three vertical dipoles. Each array provides relatively uniform illumination (2-3 dB) in the forward 180 angular segment of the horizontal plane and approximately + 10-150 coverage in the vertical plane. The antenna could be used in a two-mode operation, either in a standard monopulse radar system (sum and difference amplitude patterns) or in a system where amplitude and phase are the measurable quantities.     

Exact Angular Accuracy of an Amplitude Comparison Sequential-Lobing Processor

Assume E1 and E2 are the squares of two sequential envelopes from the sequential lobing of an antenna in a given plane. Independent thermal noise is generally present in the envelopes. The statistic e = (E2 ? E1)/(E2 + E1) has been used as an estimate of the angle to a target for the significant region of small angles compared to a beamwidth. For a nonfading target, the probability density and characteristic function of e are obtained in closed form. Thence, the exact bias, standard deviation, and rms error in estimating the noise-free value e of e are obtained for all e and signal-to-noise ratios. The same type of statistic as e can be used to estimate time delay in a split range gate tracker.     

单脉冲双极化天线阵列设计

文章研究了单脉冲双极化天线阵列。天线阵混合馈电微带单元由共面微带线馈电和缝隙耦合微带线馈电两者结合形成,"十"字形微带单脉冲比较器与天线阵同面,具有结构紧凑、加工方便和成本低的优点。经仿真验证,在工作频带内其辐射单元双端口隔离度高于34dB;并且2个极化端口在其对应主平面方向的副瓣电平均低于-20dB。天线可适用于新一代多极化雷达系统。     

机载无线电罗盘垂直天线电参数分析

从机载无线电罗盘垂直天线的实际应用出发，首先对垂直天线的电参数进行了简单的介绍和说明，然后依据等效电路理论对天线的各项参数的相互关系进行了详细的分析和推导，并列举了相关的试验方法和试验结果，进一步说明了垂直天线电性能是其相关电参数折衷的结果，最后对非独立垂直天线设计中的关键问题提出了相关建议。     

Radically new design of SAR satellite: short vertical antennaapproach

The idea of this work is the use of a vertical antenna (antenna placed in the orbit plane) for a spaceborne radar. This surprising geometry is proven to work properly and to simplify the design of the instrument, particularly when it is associated with a short antenna length (<5 m, along speed vector). The number of antenna control points is greatly reduced, which saves cost and mass of an active antenna. A single pencil beam allows all the incidences and modes to be achieved. Viewing on both sides of the satellite track is enabled. Spotlight mode is no longer needed and therefore most of the operational constraints attached to high resolution are removed. Merits of the geometry are not limited to the instrument, a cascade of other innovations converges into a radically new design of the whole satellite for an ultimate goal of simplification and cost reduction, this is radar SAIL concept. The merits and cost savings of short vertical antenna are illustrated with a 1 m resolution X band mission, and the extra merits of the integrated SAIL architecture with respect to the standard satellite architecture are discussed     

极化滤波反射面隐身天线研究

介绍了一种极化滤波反射面天线,将天线工程中的周期结构反射面技术应用于解决飞行器天线的RCS问题,采用由金属丝栅网构成的周期结构作为天线主反射面,使其对正交极化的来波具有良好的透射性,从而降低了天线的RCS。给出了此天线辐射方向图和雷达散射截面(RCS)的实测结果,并与普通金属反射面天线的结果进行了比较。     

Array antennas for DGPS

Multipath interference limits the speed and accuracy of determining position by “differential” GPS techniques. A geodetic surveyor, for example, requires multipath interference rejection of about 36+20 log₁₀ sin ϵ dB, where ϵ is the elevation angle of the satellite being observed. Signal processing in a GPS receiver cannot satisfy this requirement. A receiving antenna is required that can sufficiently reject signals arriving from below the horizon. Available antennas have inadequate rejection, and brute-force methods of improving them, by enlarging their ground-planes, are impractical. A compact, ground-planeless, dual-band, GPS antenna with improved multipath rejection has been designed and field-tested. This antenna resembles a vertical post rather than a horizontal platter; within its 0.1-m diameter, 0.4-m tall radome is a vertical array of turnstile elements. In field tests, a three-element array antenna rejected multipath better than a 0.5-m diameter ground-plane antenna by an average of 5 dB. A five-element array antenna appears superior to a 0.9-m diameter ground-plane antenna     

New Developments in Radar and Radio Sensors for Aircraft Navigation

Recent developments in airborne Doppler and ground mapping navigation radars and ground and satellite based radio systems are described. Simultaneous lobing and slope tracking techniques can remove the well-known Doppler sea bias error in fast and slowly moving vehicles. Doppler velocity information can be extracted from coherent forward-looking mapping radars, and high position fixing accuracy can be achieved by synthetic aperture radars. In radio navigation systems, such as Loran, Omega, and satellite systems, direct-ranging and differential techniques greatly reduce the geometric dilution and propagation effects which have plagued conventional radio navigation systems. The advantages gained by mixing of the data from these and other navigation sensors in a digital multisensor system are discussed and approaches for processing these data are suggested.     

定向通信系统天线波束指向误差分析

对影响定向通信系统天线波束指向误差的因素进行了分析,给出了一种特殊情形下波束指向误差与姿态角的关系式,同时给出了一般情形下基于最小二乘估计的波束指向误差与姿态角关系的推导方法.给出的关系式和方法对分析定向通信系统波束指向误差提供了理论依据,有助于评估定向通信系统的波束对准情况.     

电机电流分析法在测控天线传动系统故障诊断中的应用

分析了天线传动系统影响电机电流特性的因素，提出了天线正常跟踪卫星以及电机启动、制动时的电流特性标准，利用电机电流分析法对测控天线传动系统的周期性故障、阻尼增大故障以及系统级故障进行定位判断。结果表明，电机电流分析法可以作为天线传动系统故障诊断的一种有效手段。     

机载天线及其布局设计要求

结合机载天线的实际工程应用,从载机平台物理性能、任务系统功能要求、天线方向图覆盖以及系统电磁兼容性等几个方面对如何合理地设计天线布局进行了分析;列举了一些任务系统天线的最优布局位置,进一步说明了合理的天线布局是载机平台的物理性能和系统电气性能的折衷结果,并针对未来机载天线的发展趋势提出了一些看法。     

A Novel Slots-and-Monopole Antenna with a Steerable Cardioid Pattern

The outputs of a vertical monopole and two mutually perpendicular slots in a horizontal plane can be properly combined to yield a steerable cardioid-shaped pattern for vertically polarized waves. The required weighting factors for placing the pattern null in any desired direction are presented in graphical form. The shape and the half-power beamwidth of the steerable pattern are examined. This combination antenna unit offers important advantages in direction finding and other applications, especially at microwave frequencies.     

ILS-a safe bet for your future landings

An argument is presented in favor of the ILS (instrument landing system), the principal components of which are the localizer, which provides lateral guidance to the pilot, and the glide slope, which gives the vertical guidance. A pilot flying these signals precisely will end up over the hard surface runway with the ILS receiving antenna, wherever it is mounted on the aircraft, being about 20 ft above the touchdown point. The safety record and evolution of the ILS are examined, and a pilot's view of ILS (that of the author, an engineer who has worked with ILS since 1957 and a pilot who has used ILS safely for over 30 years) is given. System availability is discussed, and comments concerning future use are offered     

Optical fiber geostationary tether satellite (F-GTS) system design

The geostationary satellite orbit (GSO) is a limited natural resource and its efficient utilization is very important. The geostationary tether satellite (GTS) system has a number of satellites aligned along the local vertical on either side of the nominal geostationary position. The system is synchronized with the Earth's rotation and all the various altitudes are geostationary, Furthermore, optical-fiber geostationary tether satellite (F-GTS) system has been introduced to improve the GTS system, with regard to increment of communication capacity, simplification of interference paths and intersatellite link (ISL) capability. The F-GTS system design is discussed with the purpose of achieving a realistic satellite network. Three frequency bands, i.e., the 14/11, 30/20, and 50/40 GHz bands, are examined for selection of the optimum frequency band. The F-GTS system example for covering the service areas in Japan is discussed with regard to satellite antenna diameter, communication capacities, etc. To apply the F-GTS system to the whole GSO, the diagonal azimuth orbit arrangement method is proposed for low latitude service areas. Moreover, the F-GTS communication capacity and total communication capacity, when the F-GTS systems are applied to the whole GSO, are also examined.     

基于角度分集的机载超宽带MIMO天线设计

为了提高机载通信设备信道容量和进一步减小天线安装空间，提出一种采用角度分集技术的超宽带（UWB）多输入多输出（MIMO）天线。该天线将Vivaldi天线和超宽带槽天线进行了集成设计，无需采用解耦结构便可获得较高的端口隔离度，大大提高了数据传输率。通过在Vivaldi天线辐射臂上开一对方形缝隙和在介质板背面增加长方形辐射贴片，可以有效减小天线的尺寸，设计的UWB-MIMO天线尺寸为36 mm×36 mm×0.8 mm。给出了天线的设计流程，加工了天线实物，并对其进行了测量。仿真和实测结果表明MIMO天线具有超宽的阻抗带宽，可以覆盖整个3.1~10.6 GHz超宽带频段。Vivaldi天线阻抗带宽为2.8~15.9 GHz，UWB槽天线阻抗带宽为1.8~12.7 GHz，天线端口隔离度均在-10 dB以下。测量了天线的辐射性能和增益特性，实测结果与仿真结果吻合较好，证明了该天线的有效性。该天线可以应用于超宽带无线通信系统和机载阵列天线系统中。     

Balloon Position Determination on Venus

A position determination technique for balloons floating in the Venusian atmosphere is described. Measurements are all made using a single station of the NASA Deep Space Network. One coordinate of the fix is derived from a ranging measurement, and the other coordinate is derived from observation on earth of the polarization of a signal radiated from a linearly polarized antenna on the balloon, aligned to vertical by balloon local gravity.     

机载天线电磁兼容及布局分析

讨论机载天线电磁兼容及布局优化分析的数学模型。介绍了低频区、谐振区及光学区机载天线辐射场、电磁干扰余量的求解法。利用电磁干扰余量对机载天线电磁兼容（ＥＭＣ）问题进行了分析和求解,从而确定无线布局问题,给出了天线布局设计的流程图,并以机载微带共形天线为例,求解了其增益分布图和两微带天线元之间的电磁干扰余量。     

柔性天线面对漂浮基星载天线扰动分析及抑制

 为了研究柔性天线面弹性变形对漂浮基星载天线的扰动,采用固定界面模态综合法和Lagrange方法,通过轴末端与天线面交界面的协调关系,推导了大范围运动的星载天线刚柔耦合动力学模型,其所建立的动力学模型计算效率高并具有足够的精度。分析了柔性天线面弹性变形对星载天线的扰动,利用PD+振动力反馈控制抑制系统振动,并基于Lyapunov方法证明了控制系统的渐近稳定性。仿真结果表明：天线工作过程激起了柔性天线面弹性振动,进而引起星载天线的抖动,严重影响了星载天线的指向精度;利用其控制策略能快速抑制系统振动。结论对天线指向精度的分析与控制具有重要的理论价值及工程实际意义。