平板表面薄圆柱绕流摩擦力矢量场全局测量

针对壁面摩擦力矢量场测量问题,基于剪切敏感液晶(SSLC)涂层技术建立了一种测量平板表面摩擦力矢量场的方法。该方法基于多视角测量原理,采用六台同步相机从不同方向同时采集SSLC涂层在摩擦力作用下的颜色变化,与采用单台相机相比能够降低测量噪声,并且具有测量非定常流动的摩擦力场的潜力。应用该方法测量了平板表面薄圆柱绕流的摩擦力矢量场,结果表明:(1)SSLC涂层能够以彩色方式定性显示壁面摩擦力信息;(2)通过对不同方向观测的SSLC涂层颜色进行分析处理,该方法能够高分辨率测量薄圆柱绕流的摩擦力矢量场,详细地捕获了流动特征;(3)同一份SSLC涂层可以重复使用并且可用于测量不同的摩擦力矢量场。     

Effect of timing jitter on performance of MTI filters

The effect of transmitting timing jitter and sampling jitter on a multipulse clutter cancellation system is analyzed, and explicit expressions are obtained for the net increase in the residue clutter power due to timing jitter. The increase in mean-square error is found to be proportional to the jitter variance, with the two jitters contributing almost equally. The system analyzed can have either a recursive or nonrecursive MTI filter, and the latter includes the familiar two- and three-pulse canceller as special cases. The increase in residue clutter power for a three-pulse canceller is about 4.8 dB worse than that for a two-pulse canceller     

Equivalent transformation for a partially adaptive array

A partially adaptive array is one in which elements of a phased array are controlled or adaptively weighted in groups or in which certain elements, called auxiliary elements, are made controllable. Mathematically, this type of array is formed by transforming all of the elements of an array by a nonsquare matrix such that the resulting output vector has a length less than the number of array elements. It is shown that there is an equivalent matrix transform that can effectively be utilized in analyzing the partially adaptive array's performance when a small number of external jammers are present. Processor implementation and convergence rate considerations lead to the desirability of reducing the dimensionality of the cancellation processor while maintaining good sidelobe interference protection. A meaningful measure of canceller performance is to compute the optimal output signal-to-noise ratio. This expression is a function of the jammer, direction-of-arrival vectors (DOAVs), jammer powers, the array steering vector, and internal noise. It is shown that if this expression is computed for the fully adaptive array then it is easily computed for the partially adaptive array by transforming the jammer DOAVs and the steering vector by the orthogonal projection matrix defined by the rows of the subarray transformation matrix and substituting these vectors back into the original expression for the fully adaptive array     

机载MIMO雷达空时自适应杂波对消器

针对机载多输入多输出(MIMO)雷达杂波分布呈现空时耦合特性,提出一种空时自适应杂波对消器.利用机载MIMO雷达的脉冲回波数据,构造杂波对消器的系数矩阵.通过空时自适应杂波对消器的预处理,可以有效地抑制杂波,并通过与常规空时处理算法的级联,最终可以有效提高动目标的检测性能.实现了由传统地基雷达杂波对消器向机载运动平台的推广.仿真结果表明,这种自适应杂波对消器不仅适用于正侧视雷达,对于非正侧视雷达也同样适用.     

Adaptive digital beamforming for angle estimation in jamming

A radar digital beamforming (DBF) architecture and processing algorithm is described for nulling the signal from a mainlobe electronic jammer and multiple sidelobe electronic jammers while maintaining monopulse angle estimation accuracy on the target. The architecture consists of a sidelobe jamming (SLJ) cancelling adaptive array (AA) followed by a mainlobe jamming (MLJ) canceller. A mainlobe maintenance (MLM) technique or constrained adaptation during the sidelobe cancellation process is imposed so that the results of the SLJ cancellation process do not distort the subsequent mainlobe cancellation process. The SLJ signals and the MLJ signals are thus cancelled sequentially in separate processes. This technique was developed for improving radar processing in determining the angular location of a target, and specifically for improving the monopulse technique by maintaining the accuracy of the target echo monopulse ratio in the presence of electronic jamming by adaptive suppression of the jamming signals before forming the monopulse sum and difference beams     

New approach for suppression of FM jamming in GPS receivers

A new approach is proposed for the suppression of FM jammers in C/A code GPS receivers. This approach is based on the cascading of the augmented-state approximate conditional mean (ASACM) filter and the discrete wavelet transform (DWT) filter. An ASACM filter for single interference suppression in spread-spectrum systems has been reported in the recent literature. However, the formulation of the ASACM filter and its performance analysis is lacking in the case of suppression of multiple FM interferences. The ASACM filter is formulated here for the suppression of multiple FM jammers. Further, a DWT filter using biorthogonal wavelet is suggested for the suppression of FM jammers. Finally, these two filters are cascaded to get an optimum performance for higher jammer to signal ratio, which is of importance in the GPS, for the case of suppression of multiple FM jammers. The performance of the proposed filters is analyzed through simulation examples for the suppression of single and multiple FM jammers in GPS receivers     

多干扰机InSAR欺骗干扰方法

单航过的干涉合成孔径雷达（InSAR）有很强的抗干扰能力,单部干扰机所发射干扰信号的干涉相位在不同快时间是完全相同的,不同慢时间也近似相等,不能产生具有高程信息的干扰图像。基于此,提出了一种利用双（多）干扰机产生InSAR三维图像欺骗干扰的方法,分析了InSAR的成像机理,给出了假目标模板设置方法,讨论了聚焦后复图像和干涉相位要求的干扰信号调制参数以及干涉相位的估计方法。产生的干扰信号在雷达接收机中可独立实现SAR二维像干扰,经干涉后能生成虚假高程信息,理论分析和仿真结果表明,该方法能实现对SAR二维成像和InSAR三维成像的有效干扰。     

Varieties of Average Monopulse Responses to Multiple Targets

A monopulse receiver exhibits three apparently distinct types of average response when the radar sees two jammers, two passive targets, or one of each. This variety of response types is analyzed and shown to be consistent, i.e., the responses are shown to be special cases of a general formula which applies to two independent targets with uniformly distributed phase difference.     

Application of the Normalized LMS Algorithm to MSLC

For some conditions, the convergence time of the conventional LMS algorithm is longer than the radar dwell time so that the MSLC technique does not cancel jammers. The convergence time depends upon the power and angular locations of the jammers. The normalized LMS technique can decrease convergence times by several orders of magnitude. It causes the convergence time to be essentially independent of the jammer powers and decreases the convergence time dependence upon location. The derivation of an exact first moment analysis of the weights for the normalized LMS algorithm is given. Simulation results are also given. There is excellent agreement between the two.     

一种利用功率反演和线性约束最小方差算法的自适应天线

介绍了一种新的基于功率反演和线性约束最小方差的算法,以高度抑制GPS接收机的干扰信号。这种结构通过提调整天线阵列的权值,实时地接收并改变来自各方向的GPS信号,同时对不同方向的干扰信号有高的抑制比。对固定和移动的干扰都做了仿真,仿真表明这种结构有很深的零点,对固定干扰信号的抑制比可达到115dB,对移动干扰信号的抑制比可达到94dB。     

The effects of IF bandpass mismatch errors on adaptive cancellation

The effects of IF bandpass mismatch errors on adaptive cancellers are investigated. Frequency mismatch errors occur because of errors in the synthesis process of the bandpass filters which are designed to be identical and are in each input channel. Tapped-delay line transversal filters can be used to compensate for these frequency mismatches and thus improve cancellation performance. A pole/zero error model of the filters is developed whereby closed-form solutions of the maximum achievable average cancellation are obtained. This cancellation is a function of the order of the ideally matched frequency filters, the number of time-delay taps in the compensating transversal filter, the bandwidth-tapped time-delay product, and the constraints on these parameters. A design procedure is outlined for optimizing the canceller with respect to these parameters and their constraints; specifically, results are presented for Butterworth-type input filters. It is shown that an arbitrarily low output noise residue cannot be achieved by arbitrarily increasing the number of time-delay taps     

A Fast Beamforming Algorithm for Large Arrays

This beamforming algorithm is written specifically for array radars in which the number of array elements K is very large compared with the number of jammers L the radar is designed to suppress. It uses a set of M noise vectors to construct a basis for the jammer component of the antenna output vectors. The component of the quiescent weight vector orthogonal to each basis vector is calculated, renormalized to unit length, and identified as the adapted weight vector. This algorithm is effective in the suppression of many types of jammers. The number of noise samples M required in the construction of the adapted weight vector is approximately equal to L. In the special case of L narrowband noise jammers, for example, a choice of M = L usually reduces the receiver output jammer power to a few dBs above the white noise background. It is permissible to have M相似文献   

STAP for GPS receiver synchronization

A space-time adaptive processing (STAP) algorithm for delay tracking and acquisition of the GPS signature sequence with interference rejection capability is developed. The interference can consist of both broadband and narrowband jammers, and is mitigated in two steps. The narrowband jammers are modelled as vector autoregressive (VAR) processes and rejected by temporal whitening. The spatial ing is implicitly achieved by estimating a sample covariance matrix and feeding its inverse into the extended Kalman filter (EKF). The EKF estimates of the code delay and the fading channel are used for a t-test for acquisition detection. Computer simulations demonstrate robust performance of the algorithm in severe jamming, and also show that the algorithm outperforms the conventional delay-locked loop (DLL).     

Adaptive Arrays for Multiple Simultaneous Desired Signals

Steered beam adaptive arrays for multiple simultaneous desired signals are discussed. It is shown that the performance of a steered beam adaptive array depends upon the range of input signal strengths and the choice of the steering vector. Optimum steering vectors for various input signal strengths are given. All choices of steering vectors are equally effective in the rejection of jammers.     

高灵敏GPS接收机抗干扰特性研究

采用圆环阵列天线,利用最小规范算法和线性约束最小方差算法对弱GPS信号的干扰信号进行了抑制,并分别针对固定和可变天线阵元数目以及固定和可变干扰信号等多种情况进行了仿真和分析.GPS信号的功率电平假设为-175dBW,干扰信号的功率值在-100dBW～-140dBW范围内可变.仿真结果表明,圆环天线阵列能精确地判定干扰信号的来波方向,该方法能很好地改善对来波干扰信号的赋零深度.     

两种自适应方向图峰值副瓣控制方法比较

自适应阵列（或称自适应波束形成）目前已广泛应用到雷达、声纳和通信领域中用来抑制各种干扰（有意的干扰，杂波干扰和多用户干扰等）。在雷达应用中，为了减轻脉冲欺骗式干扰或旁瓣目标并利用单脉冲雷达来准确测量目标波达方向．要求自适应方向图具有低副瓣和稳定的主瓣形状。在实际应用中，各种失配误差将降低自适应阵列的性能．这些误差包括由于目标的波达方向不精确引起的信号指向误差，由通道失配和位置扰动引起的阵列校准误差和由小样本教引起的协方差矩阵估计误差。在此情况下，自适应波束形成的性能大大下降（干扰抑制性能变差。主瓣失真和高的副瓣）。已提出了一种基于二次约束的集成峰值副瓣控制（integrated peak sidelobe control，简称IPSC）方法。该方法可以精确地控制峰值副瓣电平并产生具有稳定的主瓣形状的自适应方向图。研究IPSC中目标信号的影响和信号消除方案以进一步提高IPSC的性能。并将IPSC方法和最新提出的基于二阶锥规划（second-order cone programming，简称SOCP）的分布式峰值副瓣控制（distfibuted peak sidelobe control，简称为DPSC）新方法在性能上进行了比较。仿真结果表明。在干扰抑制性能和方向图控制质量方面IPSC比DPSC性能优越。此外IPSC比DPSC计算高效。     

基于FEM-NN-MCS模拟应力集中系数的结构可靠性分析

在机械结构可靠性分析中,由于应力集中系数的预测精度直接影响可靠性分析与计算结果,可见应力集中系数(SCF)是最主要的参数之一。采用理论方法通常很难获得应力集中系数,因此目前主要采用实验方法。采用实验方法尽管可以较精确地获得应力集中系数的数值解,但不能直接给出基本随机变量和应力集中系数之间的关系,为进一步的可靠性分析带来困难。作为可供选择途径,使用有限元法(FEM)获得应力集中系数的数据库,采用神经网络方法模拟应力集中系数,用BP神经网络建立结构的输入和输出关系,在此模型上,将MonteCarlo和可靠性理论相结合,提出了解决应力集中情况下的结构可靠性问题的分析方法。     

垂直轴风力机桨叶气膜加热的数值研究

为观察风力机叶片在前缘开孔和不开孔两种情况下旋转叶片表面成膜情况,基于双向多流管理论模型,采用 MATLAB 软件编写程序及 Fluent 进行数值模拟,将程序计算结果与数值模拟结果进行比对,基于数值模拟分析两种模型在不同孔射流速度下的气动特性及流场情况。结果表明,数值模拟能够很好地反映流场特性,在来流风速及转速一定的条件下,孔射流速度过大会极大地削弱旋转叶片的气动性能,过小又不能形成很好的气膜保护。研究结果对 H 型垂直轴风力机防除冰叶片的设计具有一定的参考意义。     

Optimal weight extraction for adaptive beamforming using systolicarrays

Systolic algorithms and architectures for parallel and fully pipelined instantaneous optimal weight extraction for multiple sidelobe canceller (MSC) and minimum variance distortionless response (MVDR) beamformer are presented The proposed systolic parallelogram array processors are parallel and fully pipelined, and they can extract the optimal weights instantaneously without the need for forward or backward substitution. We also show that the square-root-free Givens method can be easily incorporated to improve the throughput rate and speed up the system. As a result these MSC and MVDR systolic array weight extraction system are suitable for real-time very large scale integration (VLSI) implementation in practical radar/sonar system     

Application of Adaptive Arrays to Suppress Strong Jammers in the Presence of Weak Signals

The purpose of this paper is to demonstrate that an adaptive array can be used to acquire weak signals, whose direction and timing are unknown, in an environment of stronger jammers. Specifically, it is shown that in an environment of one weak signal and one strong jammer, the adaptive array output suppresses the strong jammer below the weak signal by roughly the same amount that the jammer exceeded the signal before adaptation.